Author: United States. Federal Power CommissionPublisher:
ISBN:
Category : Desulfurization
Languages : en
Pages : 82
Book Description
The Status of Flue Gas Desulfurization Applications in the United States
Author: United States. Federal Power CommissionPublisher:
ISBN:
Category : Desulfurization
Languages : en
Pages : 82
Book Description
The Status of Flue Gas Desulfurization Applications in the United States
Author: Application and Development Trend of Flue Gas Desulfurization (FGD) Process
Author: Rehan JamilPublisher:
ISBN: 9783656601395
Category :
Languages : en
Pages : 20
Book Description
Scholarly Research Paper from the year 2013 in the subject Engineering - Chemical Engineering, grade: Master, course: Engineering, language: English, abstract: In 1927, the limestone desulfurization process was first applied in the Barthes and Bansside Power Plants (total 120MW) beside the Thames River in UK to protect high-rise building in London. Up to now, over 10 desulfurization processes have been launched and applied. Based on the desulfurizing agent being used, there include calcium process (limestone/lime), ammonia process, magnesium process, sodium process, alkali alumina process, copper oxide/zinc process, active carbon process, ammonium dihydrogen phosphate process, etc. The calcium process is commercially available and widely used in the world, i.e. more than 90%. Flue gas desulfurization processes, survey made by the coal research institute under the International Energy Agency shows that the wet-process desulfurization accounts for 85% of total installed capacity of flue gas desulfurization units across the world. The wet-process desulfurization is mainly applied in countries, like Japan (98%), USA (92%), Germany (90%), etc. The limestone-gypsum wet desulfurization process, the most mature technology, the most applications, the most reliable operation in the world, may have rate of desulfurization of more than 90%. Currently, the flue gas desulfurization technology used at thermal power plants at home and abroad tends to be higher rate of desulfurization, bigger installed capacity, more advanced technology, lower investment, less land acquisition, lower operation cost, higher level of automation, more excellent reliability, etc. This paper briefs current situations and trends of flue gas desulfurization technology also append short descript of different type of FDG and their category.
Flue Gas Desulfurization and Industrial Minerals
Author: M. Michael MillerPublisher:
ISBN:
Category : Flue gases
Languages : en
Pages : 720
Book Description
Contains 4,101 references on FGD [Flue Gas Desulfurization] ... primarily from 1982 through June 1993. Complements the "Flue Gas Desulfurization and Denitrification" bibliography published by the U.S. Dept. of Energy in Jan. 1985. References were located on the Energy, Science and Technology, Pollution Abstracts, and Environmental Bibliography databases. Primarily covers FGD and the use of industrial minerals in the desulfurization process or in by-product utilization and disposal. Emphasizes post-combustion removal of sulfur dioxide through processes such as in-duct injection and wet and dry scrubbing.
Sulphur Dioxide and Nitrogen Oxides in Industrial Waste Gases
Author: Daniel van VelzenPublisher: Springer Science & Business Media
ISBN: 9401136246
Category : Science
Languages : en
Pages : 281
Book Description
D. VAN VELZEN Commission of the European Communities, Joint Research Centre Ispra, Environment Institute, 1-21020 Ispra (Varese) ITAL Y 1. Introduction Worldwide, there is an ever increasing interest and concern about the destructive effects of air pollution on man's ecosystem. The growing awareness of these effects has revealed the need to take adequate measures to minimize the emission of air polluting products. The two most important contaminants, occurring in the largest concentrations and quantities, are sulphur dioxide and nitrogen oxides. Both pollutants are formed mainly during the combustion of fossil fuels, particularly by power stations and traffic. The effects of air pollution caused by these two contaminants have already been studied for several decades and measures to protect the environment against their adverse effects are now operative in many countries. The present volume contains the proceedings of a Eurocourse held in Ispra in September 1990. The course was meant to give an overview of present knowledge concerning the emission sources and quantities, to cover features of present legislation and to give a survey of the most important modern abatement techniques for S02 and NOx. It was mainly addressed to higher and medium management in the power, chemical and similar industries, particularly from those countries where the fight against air pollution is still in its infancy. Obviously, it was not possible to cover completely the whole range of subjects during the limited duration of a Eurocourse.
Flue Gas Desulfurization and Its Alternatives
Author: Arthur P. HurterPublisher:
ISBN:
Category : Flue gas
Languages : en
Pages : 136
Book Description
Flue gas desulfurization in power plants
Author: United States. Environmental Protection Agency. Division of Stationary Source EnforcementPublisher:
ISBN:
Category : Desulfurization
Languages : en
Pages : 100
Book Description
Profiles in Flue Gas Desulfurization
Author: Richard R. LuntPublisher: John Wiley & Sons
ISBN: 047093543X
Category : Technology & Engineering
Languages : en
Pages : 144
Book Description
As the need to control process emissions has increased, so have the number of FGD treatment and control strategies. The effectiveness of these treatments vary greatly, depending the types and levels of the materials, as well as the size of the facility. Profiles in Flue Gas Desulfurization will help engineers and managers identify the technologies that best fit their plant and/or processes. It’s a quick and easy reference to all “tail-end” SO2 control processes currently in commercial use or “on the brink,” providing an effective “snapshot” of where this technology stands in industry today. The technologies are divided into waste producing processes, where the end product is a “clean waste,” and byproduct processes, where the end product has market value. Each technology profile includes a schematic depicting its major equipment components and arrangement, laid out side-by-side with descriptive text on how the process works, where and how it is currently being utilized, its operational requirements, advantages and limitations for typical applications, and a brief list of principal suppliers.
Author: J. Buroff
Author: