Reduction of Cupric Oxide by Hydrogen PDF Download

Author: W. D. Bond
Publisher:
ISBN:
Category : Chemical kinetics
Languages : en
Pages : 32

View

Book Description

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :

View

Book Description
Basic studies of the kinetics of the reduction of copper oxide were made to establish the effect of the solid phase on the over-all reaction kinetics The reaction CuO + H/sub 2/ at the only rea Cu + H/sub 2/O consisted of an induction stage, an acceleration or autocatalytic stage terminating at about 35% reduction of the exide, and a decreasing-rate stage The reduction rates for each stage were dependent on the nature of the initial oxide, the degree of subdivision of the oxide, and the temperature but were independent of the mass of the oxide phase. Addition of the reaction product copper had no measurable effect on the reaction. Water vapor in concentrations of 25 mg per liter of H prevented reduction at 112 ction prod- C The inhibiting effect decreased rapidly as the temperature was increased and disappeared entirely at 190 ction prod- C. Once reduction bad started. water vapor had practically no effect The acceleration and decay stages were very closely approximated by a semiempirical equation based on the initial reaction occurring on certain active nuclei followed by a rapid growth of these nuclei by a branching-chain mechanism. The reduction rate reached a maximum and subsequentlv decreased as considerable interference occurred among the branching nuclei. Arrhenius plots gave an activation energy- of 13.5 plus or minus 1.2);cal for the reduction. (auth).

Author: W. D. Bond
Publisher:
ISBN:
Category : Copper oxide
Languages : en
Pages : 22

View

Book Description

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :

View

Book Description
The conditions under which hydrogen could be quantitatively recovered from mixtures of gases by oxidation over fixed beds of CuO were investigated. The conversion of H/sub 2/ to H/sub 2/O by reduction of CuO in fixed beds increased with in- creasing bed length, temperature, hydrogen/argon ratio, and decreasing mesh size of CuO. Residence times required for 99% conversion in a 1- in.-diam. bed were 0.6 and 1.2 sec for 30% hydrogen-70% argon and 10% hydrogen90% argon mixtures, respectively, at a total gas flow of 1 l/min. The CuO used was 25-mil-diam. wires with a surface area of 0.019 m/sup 2//g. The residence time required for a given value of conversion decreased about 10% when the total flow rate was increased from 1 to 1.7 liters/min, which indicates that the reduction is mass-transfer controlled to a slight extent under the experimental conditions used. (auth).

Author: Zuhair A. Munir
Publisher: Wiley-VCH
ISBN:
Category : Technology & Engineering
Languages : en
Pages : 536

View

Book Description

Author: Reuben Esselstyn Wood
Publisher:
ISBN:
Category :
Languages : en
Pages :

View

Book Description

Author: Victor E. Henrich
Publisher: Cambridge University Press
ISBN: 9780521566872
Category : Science
Languages : en
Pages : 484

View

Book Description
Publisher Description

Author: H.H. Kung
Publisher: Elsevier
ISBN: 0080887422
Category : Science
Languages : en
Pages : 299

View

Book Description
In this book the author presents an up-to-date summary of existing information on the structure, electronic properties, chemistry and catalytic properties of transition metal oxides. The subjects covered in the book can be divided into three sections. The first (chapters 1 to 3) covers the structural, physical, magnetic, and electronic properties of transition metal oxides. Although the emphasis is on surface properties, relevant bulk properties are also discussed. The second section (chapters 4 to 7) covers surface chemical properties. It includes topics that describe the importance of surface coordinative unsaturation in adsorption, the formation of surface acidity and the role of acidity in determining surface chemical properties, the nature and reactivities of adsorbed oxygen, and the surface chemistry in the reduction of oxides. The third section (chapters 8 to 14) is on the catalytic properties. Various catalytic reactions including decomposition, hydrogenation, isomerization, metathesis, selective oxidation, and reactions involving carbon oxides are discussed. Emphasis is placed more on reaction mechanisms and the role of catalysts than on kinetics and processes. Chapters on the preparation of oxide catalysts and on photo-assisted processes are also included. Whenever appropriate, relationships between various topics are indicated. Written for surface physicists, chemists, and catalytic engineers, the book will serve as a useful source of information for investigators and as a comprehensive overview of the subject for graduate students.

Author: Oleg D Neikov
Publisher: Elsevier
ISBN: 0080559409
Category : Technology & Engineering
Languages : en
Pages : 644

View

Book Description
The manufacture and use of the powders of non-ferrous metals has been taking place for many years in what was previously Soviet Russia, and a huge amount of knowledge and experience has built up in that country over the last forty years or so. Although accounts of the topic have been published in the Russian language, no English language account has existed until now. Six prominent academics and industrialists from the Ukraine and Russia have produced this highly-detailed account which covers the classification, manufacturing methods, treatment and properties of the non-ferrous metals ( aluminium, titanium, magnesium, copper, nickel, cobalt, zinc, cadmium, lead, tin, bismuth, noble metals and earth metals). The result is a formidable reference source for those in all aspects of the metal powder industry. Covers the manufacturing methods, properties and importance of the following metals: aluminium, titanium, magnesium, copper, nickel, cobalt, zinc, cadmium, noble metals, rare earth metals, lead, tin and bismuth Expert Russian team of authors, all very experienced English translation and update of book previously published in Russian

Author: Thomas Carlson
Publisher: Springer Science & Business Media
ISBN: 1475701187
Category : Science
Languages : en
Pages : 427

View

Book Description
In 1970 when I first seriously contemplated writing a book on electron spectroscopy, I recognized the impossibility of completely reaching my desired goals. First, the field was expanding (and still is) at such a rate that a definitive statement of the subject is not possible. The act of following the literature comprehensively and summarizing its essential content proved to be a diver gent series. On the other hand, the field has increased to such a size that violent changes in its basic makeup no longer occur with the frequency that was present in its early days. Furthermore, the excitement of electron spectro scopy lies in its many-faceted interrelationships. In the era of specialization, electron spectroscopy is an open-ended subject continually bringing together new aspects of science. I wished to discuss not just one type of electron spectro scopy, but as many as would be possible. The book as it stands concentrates its attention on x-ray photoelectron spectroscopy, but also presents the basis of Auger electron spectroscopy and uv photoelectron spectroscopy, as well as mentioning many of the other branches of the field. A large, many-author volume might be an answer to some of these problems. However, though anyone person possesses only a limited amount of expertise, I have always enjoyed books by a single author since what they lack in detailed knowledge they gain in a unified viewpoint. I hope the final product, though limited in its attainment of these goals, will still be of some merit.