Author: Fasteners Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and quality requirements for two grades of carbon steel, slotted, and recessed, 82 degrees flat countersunk, 82 degrees oval countersunk, pan, fillister, hex, and hex washer head machine screws in sizes No. 4 through 3/4 in for use automotive and related industries. The dimensions of these screws are covered in ASME B18.6.3. Current requirements for Machine Screws are contained in ASME B18.6.3 - Machine Screws, Tapping Screws, and Metallic Drive Screws (Inch Series). SAE J82 contains useful information and may have current users.
Mechanical and Quality Requirements for Machine Screws
Author: Fasteners Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and quality requirements for two grades of carbon steel, slotted, and recessed, 82 degrees flat countersunk, 82 degrees oval countersunk, pan, fillister, hex, and hex washer head machine screws in sizes No. 4 through 3/4 in for use automotive and related industries. The dimensions of these screws are covered in ASME B18.6.3. Current requirements for Machine Screws are contained in ASME B18.6.3 - Machine Screws, Tapping Screws, and Metallic Drive Screws (Inch Series). SAE J82 contains useful information and may have current users.
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and quality requirements for two grades of carbon steel, slotted, and recessed, 82 degrees flat countersunk, 82 degrees oval countersunk, pan, fillister, hex, and hex washer head machine screws in sizes No. 4 through 3/4 in for use automotive and related industries. The dimensions of these screws are covered in ASME B18.6.3. Current requirements for Machine Screws are contained in ASME B18.6.3 - Machine Screws, Tapping Screws, and Metallic Drive Screws (Inch Series). SAE J82 contains useful information and may have current users.
Mechanical and Quality Requirements for Tapping Screws
Author: Fasteners Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Recommended Practice covers the mechanical and quality requirements for steel tapping screws used in automotive and related industries. It does not apply to corrosion resistant (stainless) steel screws. (Dimensional requirements for most types of screws mentioned herein are covered in ASME B 18.6.4, Thread Forming and Thread Cutting Tapping Screws and Metallic Drive Screws'.) Current requirements for Tapping Screws are contained in ASME B18.6.3 - Machine Screws, Tapping Screws, and Metallic Drive Screws (Inch Series) and SAE J2596 - Fastener Part Standard - Tapping Screws and Metallic Drive Screws (Inch Dimensioned). SAE J933 contains useful information and may have current users.
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Recommended Practice covers the mechanical and quality requirements for steel tapping screws used in automotive and related industries. It does not apply to corrosion resistant (stainless) steel screws. (Dimensional requirements for most types of screws mentioned herein are covered in ASME B 18.6.4, Thread Forming and Thread Cutting Tapping Screws and Metallic Drive Screws'.) Current requirements for Tapping Screws are contained in ASME B18.6.3 - Machine Screws, Tapping Screws, and Metallic Drive Screws (Inch Series) and SAE J2596 - Fastener Part Standard - Tapping Screws and Metallic Drive Screws (Inch Dimensioned). SAE J933 contains useful information and may have current users.
MECHANICAL AND QUALITY REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS
Author: Fasteners Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and quality requirements for steel bolts, screws, studs, and sems used in automotive and related industries in sizes to 1 in, inclusive. This standard does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For certain type, size, and length of products this may be done by the statement: "Surface discontinuities shall not exceed the limits shown in SAE J123."NOTE: Previous issues of this standard also covered nuts, now covered separately in SAE J995.
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and quality requirements for steel bolts, screws, studs, and sems used in automotive and related industries in sizes to 1 in, inclusive. This standard does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For certain type, size, and length of products this may be done by the statement: "Surface discontinuities shall not exceed the limits shown in SAE J123."NOTE: Previous issues of this standard also covered nuts, now covered separately in SAE J995.
NBS Special Publication
Author:
Publisher:
ISBN:
Category : Weights and measures
Languages : en
Pages : 1064
Book Description
Publisher:
ISBN:
Category : Weights and measures
Languages : en
Pages : 1064
Book Description
Mechanical and Material Requirements for Externally Threaded Fasteners
Author: Fasteners Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 in sizes to 1-1/2 in. inclusive.The term "stud" as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing. Other properties such as fatigue behavior, corrosion resistance, impact properties, etc., are beyond the scope of this document and responsibility for ensuring the acceptability of the product for applications where conditions warrant consideration of these other properties shall be borne by the end user. Allow higher S and P percentages in alloy steel than allowed in Table 2 for manufacturing Grade 8 screws and bolts by hot forging or machining from bar. As an example, this enables producers of Grade 8 bolts and screws to use SAE 4140 steel that might not otherwise be acceptable for hot forging and machining from bar. The S and P values in Table 2 must be adhered to for all cold formed fasteners.
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 in sizes to 1-1/2 in. inclusive.The term "stud" as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing. Other properties such as fatigue behavior, corrosion resistance, impact properties, etc., are beyond the scope of this document and responsibility for ensuring the acceptability of the product for applications where conditions warrant consideration of these other properties shall be borne by the end user. Allow higher S and P percentages in alloy steel than allowed in Table 2 for manufacturing Grade 8 screws and bolts by hot forging or machining from bar. As an example, this enables producers of Grade 8 bolts and screws to use SAE 4140 steel that might not otherwise be acceptable for hot forging and machining from bar. The S and P values in Table 2 must be adhered to for all cold formed fasteners.
Mechanical and Material Requirements for Metric Externally Threaded Steel Fasteners
Author: Fasteners Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications. Current requirements for Mechanical and Quality Requirements for Metric Externally Threaded Steel Fasteners are contained in ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel - Bolts, screws, and studs. SAE J1199 contains useful information and may have current users. However, several of the references have been cancelled or superseded.
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications. Current requirements for Mechanical and Quality Requirements for Metric Externally Threaded Steel Fasteners are contained in ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel - Bolts, screws, and studs. SAE J1199 contains useful information and may have current users. However, several of the references have been cancelled or superseded.
American National Standard
Author: American Society of Mechanical Engineers
Publisher:
ISBN:
Category :
Languages : en
Pages : 74
Book Description
Publisher:
ISBN:
Category :
Languages : en
Pages : 74
Book Description
An Index of U.S. Voluntary Engineering Standards
Author: United States. National Bureau of Standards
Publisher:
ISBN:
Category : Standards, Engineering
Languages : en
Pages : 1038
Book Description
Publisher:
ISBN:
Category : Standards, Engineering
Languages : en
Pages : 1038
Book Description
American Standard Screw Threads for Bolts, Machine Screws, Nuts, and Commercially Tapped Holes
Author: Society of Automotive Engineers
Publisher:
ISBN:
Category : Bolts and nuts
Languages : en
Pages : 34
Book Description
Publisher:
ISBN:
Category : Bolts and nuts
Languages : en
Pages : 34
Book Description
An Index of U.S. Voluntary Engineering Standards
Author: William J. Slattery
Publisher:
ISBN:
Category : Standards, Engineering
Languages : en
Pages : 1016
Book Description
Publisher:
ISBN:
Category : Standards, Engineering
Languages : en
Pages : 1016
Book Description