Author: Guy Bellows
Publisher:
ISBN:
Category : Grinding and polishing
Languages : en
Pages : 124
Book Description
It has been known for many centuries that grinding can 'burn' metal and reduce its strength. Beginning in the 1940's this knowledge was quantified as seen by the example of the fatigue strengths produced by grinding AISI 4340 steel, quenched and tempered to 50 r sub c: (1) Low stress grinding 102 KSI; (2) Conventional grinding 75 KSI; and (3) High stress grinding 62 KSI. The values shown represent the fatigue strength at ten to the 7th power cycles at room temperature for flat cantilever specimens run at full reverse bending. The specimens were prepared with three different levels of grinding intensity. The substantial strength reduction, even with conventional grinding parameters, is of concern where the ground components are to be used in highly stressed applications.
Low Stress Grinding for Quality Production
Author: Guy Bellows
Publisher:
ISBN:
Category : Grinding and polishing
Languages : en
Pages : 124
Book Description
It has been known for many centuries that grinding can 'burn' metal and reduce its strength. Beginning in the 1940's this knowledge was quantified as seen by the example of the fatigue strengths produced by grinding AISI 4340 steel, quenched and tempered to 50 r sub c: (1) Low stress grinding 102 KSI; (2) Conventional grinding 75 KSI; and (3) High stress grinding 62 KSI. The values shown represent the fatigue strength at ten to the 7th power cycles at room temperature for flat cantilever specimens run at full reverse bending. The specimens were prepared with three different levels of grinding intensity. The substantial strength reduction, even with conventional grinding parameters, is of concern where the ground components are to be used in highly stressed applications.
Publisher:
ISBN:
Category : Grinding and polishing
Languages : en
Pages : 124
Book Description
It has been known for many centuries that grinding can 'burn' metal and reduce its strength. Beginning in the 1940's this knowledge was quantified as seen by the example of the fatigue strengths produced by grinding AISI 4340 steel, quenched and tempered to 50 r sub c: (1) Low stress grinding 102 KSI; (2) Conventional grinding 75 KSI; and (3) High stress grinding 62 KSI. The values shown represent the fatigue strength at ten to the 7th power cycles at room temperature for flat cantilever specimens run at full reverse bending. The specimens were prepared with three different levels of grinding intensity. The substantial strength reduction, even with conventional grinding parameters, is of concern where the ground components are to be used in highly stressed applications.
Metals Handbook: Machining
Tool and Manufacturing Engineers Handbook: Machining
Author: Thomas J. Drozda
Publisher: Society of Manufacturing Engineers
ISBN: 0872630854
Category : Technology & Engineering
Languages : en
Pages : 1434
Book Description
Part of the renowned Tool and Manufacturing Engineers Handbook Series, the Machining Vol. 1 helps you apply cost-effective techniques to achieve the best results for over 100 traditional and nontraditional machining processes. Chapters include: Principles of Metalcutting and Machinability, Tolerance Control, Cutting Tool Materials, Sawing, Broaching, Planing, Shaping, and Slotting, Turning and Boring, Milling, Grinding, Threading Gear and Spline Production, Nontraditional Machining, Machine Loading and Unloading, Machine Rebuilding, and much more!
Publisher: Society of Manufacturing Engineers
ISBN: 0872630854
Category : Technology & Engineering
Languages : en
Pages : 1434
Book Description
Part of the renowned Tool and Manufacturing Engineers Handbook Series, the Machining Vol. 1 helps you apply cost-effective techniques to achieve the best results for over 100 traditional and nontraditional machining processes. Chapters include: Principles of Metalcutting and Machinability, Tolerance Control, Cutting Tool Materials, Sawing, Broaching, Planing, Shaping, and Slotting, Turning and Boring, Milling, Grinding, Threading Gear and Spline Production, Nontraditional Machining, Machine Loading and Unloading, Machine Rebuilding, and much more!
Nondestructive Characterization of Materials II
Author: Jean F. Bussière
Publisher: Springer Science & Business Media
ISBN: 1468453386
Category : Technology & Engineering
Languages : en
Pages : 750
Book Description
The possibility of nondestructively characterizing the microstruc ture, morphology or mechanical properties of materials is certainly a fascinating subject. In principle, such techniques can be used at all stages of a material's life - from the early stages of processing, to the end of a structural component's useful life. Interest in the subject thus arises not only from a purely scientific point of view but is also strongly motivated by economic pressures to improve productivity and quality in manufacturing, to insure the reliability and extend the life of existing structures. The present volume represents the edited papers presented at the Second International Symposium on the Nondestructive Characterization of Materials, held in Montreal, Canada, July 21-23, 1986. The Proceedings are divided into eight sections, which reflect the multidisciplinary nature of characterizing materials nondestructively: Polymers and Composites, Ceramics and Powder Metallurgy, Metals, Layered Structures/Adhesive Bonds/Welding, Degradation/Aging, Texture/ Anisotropy, Stress, and New Techniques. Invited papers by R. Hadcock of Grumman Aircraft Systems, R. Cannon of Rutgers University, H. Yada of Nippon Steel and R. Bridenbaugh of Alcoa review respectively the processing of polymer matrix composites, ceramics, steel and aluminum, emphasizing the need for material property sensors to improve process and quality control. Two other invited papers, one by A. Wedgwood of Harwell and the other by P. Holler of the IzFP in Saarbrucken review state of the art techniques to characterize particulate matter and metals respectively.
Publisher: Springer Science & Business Media
ISBN: 1468453386
Category : Technology & Engineering
Languages : en
Pages : 750
Book Description
The possibility of nondestructively characterizing the microstruc ture, morphology or mechanical properties of materials is certainly a fascinating subject. In principle, such techniques can be used at all stages of a material's life - from the early stages of processing, to the end of a structural component's useful life. Interest in the subject thus arises not only from a purely scientific point of view but is also strongly motivated by economic pressures to improve productivity and quality in manufacturing, to insure the reliability and extend the life of existing structures. The present volume represents the edited papers presented at the Second International Symposium on the Nondestructive Characterization of Materials, held in Montreal, Canada, July 21-23, 1986. The Proceedings are divided into eight sections, which reflect the multidisciplinary nature of characterizing materials nondestructively: Polymers and Composites, Ceramics and Powder Metallurgy, Metals, Layered Structures/Adhesive Bonds/Welding, Degradation/Aging, Texture/ Anisotropy, Stress, and New Techniques. Invited papers by R. Hadcock of Grumman Aircraft Systems, R. Cannon of Rutgers University, H. Yada of Nippon Steel and R. Bridenbaugh of Alcoa review respectively the processing of polymer matrix composites, ceramics, steel and aluminum, emphasizing the need for material property sensors to improve process and quality control. Two other invited papers, one by A. Wedgwood of Harwell and the other by P. Holler of the IzFP in Saarbrucken review state of the art techniques to characterize particulate matter and metals respectively.
Tool and Manufacturing Engineers Handbook: Quality Control and Assembly
Author: Thomas J. Drozda
Publisher: Society of Manufacturing Engineers
ISBN: 087263177X
Category : Technology & Engineering
Languages : en
Pages : 828
Book Description
Quality Control and Assembly helps you meet today's competitive pressures for measuring quality, making continuous quality improvements, streamlining assembly, and making the transition to automated assembly systems and applications.
Publisher: Society of Manufacturing Engineers
ISBN: 087263177X
Category : Technology & Engineering
Languages : en
Pages : 828
Book Description
Quality Control and Assembly helps you meet today's competitive pressures for measuring quality, making continuous quality improvements, streamlining assembly, and making the transition to automated assembly systems and applications.
Residual Stresses
Author: A. Niku-Lari
Publisher: Elsevier
ISBN: 1483191001
Category : Science
Languages : en
Pages : 587
Book Description
Residual Stresses presents a collection of articles that provides information regarding the use of surface treatment systems. It discusses the developments in the technology and application of surface treatment. It addresses the influence of minor stresses on the performance of materials. Some of the topics covered in the book are the introduction to self-equilibrating stresses existing in materials, the stresses that form as a consequence of welding, the stresses made by machining, and the mechanical generation of self-stresses. The analysis of the stresses caused by thermal and thermochemical surface treatments is covered. The minor stresses in composite materials are discussed. The text describes the stresses in uranium and uranium alloys. The Trepan or ring core method, centre-hole method, and Sach's method are presented. A chapter of the volume is devoted to the measurement of residual stresses. Another section of the book focuses on the application of shot peened plates to residual stress distribution. The book will provide useful information to mechanics, engineers, students, and researchers.
Publisher: Elsevier
ISBN: 1483191001
Category : Science
Languages : en
Pages : 587
Book Description
Residual Stresses presents a collection of articles that provides information regarding the use of surface treatment systems. It discusses the developments in the technology and application of surface treatment. It addresses the influence of minor stresses on the performance of materials. Some of the topics covered in the book are the introduction to self-equilibrating stresses existing in materials, the stresses that form as a consequence of welding, the stresses made by machining, and the mechanical generation of self-stresses. The analysis of the stresses caused by thermal and thermochemical surface treatments is covered. The minor stresses in composite materials are discussed. The text describes the stresses in uranium and uranium alloys. The Trepan or ring core method, centre-hole method, and Sach's method are presented. A chapter of the volume is devoted to the measurement of residual stresses. Another section of the book focuses on the application of shot peened plates to residual stress distribution. The book will provide useful information to mechanics, engineers, students, and researchers.
Manufacturing Engineering Explores Grinding Technology
Author: Tom Drozda
Publisher:
ISBN:
Category : Technology & Engineering
Languages : en
Pages : 216
Book Description
Publisher:
ISBN:
Category : Technology & Engineering
Languages : en
Pages : 216
Book Description
Nanocosmetics
Author: Jean Cornier
Publisher: Springer
ISBN: 3030165736
Category : Science
Languages : en
Pages : 365
Book Description
This book addresses the application of nanotechnology to cosmetics. Edited by three respected experts in the field, the book begins with a general overview of the science behind cosmetics and skin care today, and of the status quo of nanotechnology in cosmetics. Subsequent chapters provide detailed information on the different nanoparticles currently used in cosmetics; the production and characterization of nanoparticles and nanocosmetics; and regulatory, safety and commercialization aspects. Given its scope, the book offers an indispensable guide for scientists in academia and industry, technicians and students, as well as a useful resource for decision-makers in the field and consumer organizations. Chapter 6 of this book is available open access under a CC BY 4.0 licence at link.springer.com.
Publisher: Springer
ISBN: 3030165736
Category : Science
Languages : en
Pages : 365
Book Description
This book addresses the application of nanotechnology to cosmetics. Edited by three respected experts in the field, the book begins with a general overview of the science behind cosmetics and skin care today, and of the status quo of nanotechnology in cosmetics. Subsequent chapters provide detailed information on the different nanoparticles currently used in cosmetics; the production and characterization of nanoparticles and nanocosmetics; and regulatory, safety and commercialization aspects. Given its scope, the book offers an indispensable guide for scientists in academia and industry, technicians and students, as well as a useful resource for decision-makers in the field and consumer organizations. Chapter 6 of this book is available open access under a CC BY 4.0 licence at link.springer.com.
Tribology of Abrasive Machining Processes
Author: Ioan D. Marinescu
Publisher: William Andrew
ISBN: 1437734685
Category : Technology & Engineering
Languages : en
Pages : 601
Book Description
This book draws upon the science of tribology to understand, predict and improve abrasive machining processes. Pulling together information on how abrasives work, the authors, who are renowned experts in abrasive technology, demonstrate how tribology can be applied as a tool to improve abrasive machining processes. Each of the main elements of the abrasive machining system are looked at, and the tribological factors that control the efficiency and quality of the processes are described. Since grinding is by far the most commonly employed abrasive machining process, it is dealt with in particular detail. Solutions are posed to many of the most commonly experienced industrial problems, such as poor accuracy, poor surface quality, rapid wheel wear, vibrations, work-piece burn and high process costs. This practical approach makes this book an essential tool for practicing engineers. - Uses the science of tribology to improve understanding and of abrasive machining processes in order to increase performance, productivity and surface quality of final products - A comprehensive reference on how abrasives work, covering kinematics, heat transfer, thermal stresses, molecular dynamics, fluids and the tribology of lubricants - Authoritative and ground-breaking in its first edition, the 2nd edition includes 30% new and updated material, including new topics such as CMP (Chemical Mechanical Polishing) and precision machining for micro-and nano-scale applications
Publisher: William Andrew
ISBN: 1437734685
Category : Technology & Engineering
Languages : en
Pages : 601
Book Description
This book draws upon the science of tribology to understand, predict and improve abrasive machining processes. Pulling together information on how abrasives work, the authors, who are renowned experts in abrasive technology, demonstrate how tribology can be applied as a tool to improve abrasive machining processes. Each of the main elements of the abrasive machining system are looked at, and the tribological factors that control the efficiency and quality of the processes are described. Since grinding is by far the most commonly employed abrasive machining process, it is dealt with in particular detail. Solutions are posed to many of the most commonly experienced industrial problems, such as poor accuracy, poor surface quality, rapid wheel wear, vibrations, work-piece burn and high process costs. This practical approach makes this book an essential tool for practicing engineers. - Uses the science of tribology to improve understanding and of abrasive machining processes in order to increase performance, productivity and surface quality of final products - A comprehensive reference on how abrasives work, covering kinematics, heat transfer, thermal stresses, molecular dynamics, fluids and the tribology of lubricants - Authoritative and ground-breaking in its first edition, the 2nd edition includes 30% new and updated material, including new topics such as CMP (Chemical Mechanical Polishing) and precision machining for micro-and nano-scale applications
Manufacturing Process Selection Handbook
Author: K. G. Swift
Publisher: Butterworth-Heinemann
ISBN: 0080993575
Category : Technology & Engineering
Languages : en
Pages : 457
Book Description
Manufacturing Process Selection Handbook provides engineers and designers with process knowledge and the essential technological and cost data to guide the selection of manufacturing processes early in the product development cycle. Building on content from the authors' earlier introductory Process Selection guide, this expanded handbook begins with the challenges and benefits of identifying manufacturing processes in the design phase and appropriate strategies for process selection. The bulk of the book is then dedicated to concise coverage of different manufacturing processes, providing a quick reference guide for easy comparison and informed decision making. For each process examined, the book considers key factors driving selection decisions, including: - Basic process descriptions with simple diagrams to illustrate - Notes on material suitability - Notes on available process variations - Economic considerations such as costs and production rates - Typical applications and product examples - Notes on design aspects and quality issues Providing a quick and effective reference for the informed selection of manufacturing processes with suitable characteristics and capabilities, Manufacturing Process Selection Handbook is intended to quickly develop or refresh your experience of selecting optimal processes and costing design alternatives in the context of concurrent engineering. It is an ideal reference for those working in mechanical design across a variety of industries and a valuable learning resource for advanced students undertaking design modules and projects as part of broader engineering programs. - Provides manufacturing process information maps (PRIMAs) provide detailed information on the characteristics and capabilities of 65 processes in a standard format - Includes process capability charts detailing the processing tolerance ranges for key material types - Offers detailed methods for estimating costs, both at the component and assembly level
Publisher: Butterworth-Heinemann
ISBN: 0080993575
Category : Technology & Engineering
Languages : en
Pages : 457
Book Description
Manufacturing Process Selection Handbook provides engineers and designers with process knowledge and the essential technological and cost data to guide the selection of manufacturing processes early in the product development cycle. Building on content from the authors' earlier introductory Process Selection guide, this expanded handbook begins with the challenges and benefits of identifying manufacturing processes in the design phase and appropriate strategies for process selection. The bulk of the book is then dedicated to concise coverage of different manufacturing processes, providing a quick reference guide for easy comparison and informed decision making. For each process examined, the book considers key factors driving selection decisions, including: - Basic process descriptions with simple diagrams to illustrate - Notes on material suitability - Notes on available process variations - Economic considerations such as costs and production rates - Typical applications and product examples - Notes on design aspects and quality issues Providing a quick and effective reference for the informed selection of manufacturing processes with suitable characteristics and capabilities, Manufacturing Process Selection Handbook is intended to quickly develop or refresh your experience of selecting optimal processes and costing design alternatives in the context of concurrent engineering. It is an ideal reference for those working in mechanical design across a variety of industries and a valuable learning resource for advanced students undertaking design modules and projects as part of broader engineering programs. - Provides manufacturing process information maps (PRIMAs) provide detailed information on the characteristics and capabilities of 65 processes in a standard format - Includes process capability charts detailing the processing tolerance ranges for key material types - Offers detailed methods for estimating costs, both at the component and assembly level