Experimental Measurement of Overall Effectiveness and Internal Coolant Temperatures for a Film Cooled Gas Turbine Airfoil with Internal Impingement Cooling PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Experimental Measurement of Overall Effectiveness and Internal Coolant Temperatures for a Film Cooled Gas Turbine Airfoil with Internal Impingement Cooling PDF full book. Access full book title Experimental Measurement of Overall Effectiveness and Internal Coolant Temperatures for a Film Cooled Gas Turbine Airfoil with Internal Impingement Cooling by Randall Paul Williams. Download full books in PDF and EPUB format.
Author: Randall Paul Williams Publisher: ISBN: Category : Languages : en Pages : 258
Book Description
A scaled-up gas turbine vane model was constructed in such a way to achieve a Biot number (Bi) representative of an actual engine component, and experiments were performed to collect temperature data which may be used to validate computational fluid dynamics (CFD) codes used in the design of gas turbine cooling schemes. The physical model incorporated an internal impingement plate to provide cooling on the inner wall surface, and film cooling over the external surface was provided by a single row of holes located on the suction side of the vane. A single row of holes was chosen to simplify the operating condition and test geometry for the purpose of evaluating CFD predictions. Thermocouples were used to measure internal gas temperatures and internal surface temperatures over a range of coolant flow rates, while infra-red thermography was used to measure external surface temperatures. When Bi is matched to an actual engine component, these measured temperatures may be normalized relative to the coolant temperature and mainstream gas temperature to determine the overall cooling effectiveness, which will be representative of the real engine component. Measurements were made to evaluate the overall effectiveness resulting from internal impingement cooling alone, and then with both internal impingement cooling and external film cooling as the coolant flow rate was increased. As expected, with internal impingement cooling alone, both internal and external wall surfaces became colder as the coolant flow rate was increased. The addition of film cooling further increased the overall effectiveness, particularly at the lower and intermediate flow rates tested, but provided little benefit at the highest flow rates. An optimal jet momentum flux ratio of I=1.69 resulted in a peak overall effectiveness, although the film effectiveness was shown to be low under these conditions. The effect of increasing the coolant-to-mainstream density ratio was evaluated at one coolant flow rate and resulted in higher values of overall cooling effectiveness and normalized internal temperatures, throughout the model. Finally, a 1-dimensional heat transfer analysis was performed (using a resistance analogy) in which overall effectiveness with film cooling was predicted from measurements of film effectiveness and overall effectiveness without film cooling. This analysis tended to over-predict overall effectiveness, at the lowest values of the jet momentum flux ratio, while under-predicting it at the highest values.
Author: Randall Paul Williams Publisher: ISBN: Category : Languages : en Pages : 258
Book Description
A scaled-up gas turbine vane model was constructed in such a way to achieve a Biot number (Bi) representative of an actual engine component, and experiments were performed to collect temperature data which may be used to validate computational fluid dynamics (CFD) codes used in the design of gas turbine cooling schemes. The physical model incorporated an internal impingement plate to provide cooling on the inner wall surface, and film cooling over the external surface was provided by a single row of holes located on the suction side of the vane. A single row of holes was chosen to simplify the operating condition and test geometry for the purpose of evaluating CFD predictions. Thermocouples were used to measure internal gas temperatures and internal surface temperatures over a range of coolant flow rates, while infra-red thermography was used to measure external surface temperatures. When Bi is matched to an actual engine component, these measured temperatures may be normalized relative to the coolant temperature and mainstream gas temperature to determine the overall cooling effectiveness, which will be representative of the real engine component. Measurements were made to evaluate the overall effectiveness resulting from internal impingement cooling alone, and then with both internal impingement cooling and external film cooling as the coolant flow rate was increased. As expected, with internal impingement cooling alone, both internal and external wall surfaces became colder as the coolant flow rate was increased. The addition of film cooling further increased the overall effectiveness, particularly at the lower and intermediate flow rates tested, but provided little benefit at the highest flow rates. An optimal jet momentum flux ratio of I=1.69 resulted in a peak overall effectiveness, although the film effectiveness was shown to be low under these conditions. The effect of increasing the coolant-to-mainstream density ratio was evaluated at one coolant flow rate and resulted in higher values of overall cooling effectiveness and normalized internal temperatures, throughout the model. Finally, a 1-dimensional heat transfer analysis was performed (using a resistance analogy) in which overall effectiveness with film cooling was predicted from measurements of film effectiveness and overall effectiveness without film cooling. This analysis tended to over-predict overall effectiveness, at the lowest values of the jet momentum flux ratio, while under-predicting it at the highest values.
Author: John W. McClintic Publisher: ISBN: Category : Languages : en Pages : 300
Book Description
This study focused on experimentally measuring the performance of a fully cooled, scaled up C3X turbine vane. Experimental measurements focused on investigating row-to-row interactions of coolant jets and the contributions of external film cooling and internal impingement cooling to overall cooling effectiveness. Overall effectiveness was experimentally measured using a thermally scaled, matched Biot number vane model featuring a realistic internal impingement scheme and had normalized surface temperatures that were representative of those found on engine components. A geometrically identical vane was also constructed out of low conductivity polystyrene foam to measure the normalized adiabatic wall temperature, or adiabatic effectiveness of the film cooling configuration. The vanes featured a full coverage film-cooling scheme with a five-row showerhead and 13 total rows of holes containing 149 total coolant holes. This study was the first study to make highly detailed measurements of overall effectiveness on a fully-cooled vane model and expands on previous studies of adiabatic and overall effectiveness on the showerhead and single rows of holes on a matched Biot vane by considering a fully cooled configuration to determine if the results from these previous studies also hold for a fully cooled configuration. Additionally, velocity and thermal fields were measured just upstream of two different suction side rows of holes in order to study the effect of introducing upstream coolant injection. The effects of mainstream turbulence and span-wise location were examined and at the downstream row of holes, the contributions of different rows of holes to the approach flow were compared. This study was the first to measure mean and fluctuating velocity data on the suction side of a turbine vane with upstream coolant injection. Understanding the effects of how upstream injection affects the performance of downstream rows of holes is critical to understanding the film cooling performance on a fully cooled turbine airfoil.
Author: Chaitanya D Ghodke Publisher: SAE International ISBN: 0768095026 Category : Technology & Engineering Languages : en Pages : 238
Book Description
Gas turbines play an extremely important role in fulfilling a variety of power needs and are mainly used for power generation and propulsion applications. The performance and efficiency of gas turbine engines are to a large extent dependent on turbine rotor inlet temperatures: typically, the hotter the better. In gas turbines, the combustion temperature and the fuel efficiency are limited by the heat transfer properties of the turbine blades. However, in pushing the limits of hot gas temperatures while preventing the melting of blade components in high-pressure turbines, the use of effective cooling technologies is critical. Increasing the turbine inlet temperature also increases heat transferred to the turbine blade, and it is possible that the operating temperature could reach far above permissible metal temperature. In such cases, insufficient cooling of turbine blades results in excessive thermal stress on the blades causing premature blade failure. This may bring hazards to the engine's safe operation. Gas Turbine Blade Cooling, edited by Dr. Chaitanya D. Ghodke, offers 10 handpicked SAE International's technical papers, which identify key aspects of turbine blade cooling and help readers understand how this process can improve the performance of turbine hardware.
Author: Je-Chin Han Publisher: CRC Press ISBN: 1439855684 Category : Science Languages : en Pages : 892
Book Description
A comprehensive reference for engineers and researchers, Gas Turbine Heat Transfer and Cooling Technology, Second Edition has been completely revised and updated to reflect advances in the field made during the past ten years. The second edition retains the format that made the first edition so popular and adds new information mainly based on selected published papers in the open literature. See What’s New in the Second Edition: State-of-the-art cooling technologies such as advanced turbine blade film cooling and internal cooling Modern experimental methods for gas turbine heat transfer and cooling research Advanced computational models for gas turbine heat transfer and cooling performance predictions Suggestions for future research in this critical technology The book discusses the need for turbine cooling, gas turbine heat-transfer problems, and cooling methodology and covers turbine rotor and stator heat-transfer issues, including endwall and blade tip regions under engine conditions, as well as under simulated engine conditions. It then examines turbine rotor and stator blade film cooling and discusses the unsteady high free-stream turbulence effect on simulated cascade airfoils. From here, the book explores impingement cooling, rib-turbulent cooling, pin-fin cooling, and compound and new cooling techniques. It also highlights the effect of rotation on rotor coolant passage heat transfer. Coverage of experimental methods includes heat-transfer and mass-transfer techniques, liquid crystal thermography, optical techniques, as well as flow and thermal measurement techniques. The book concludes with discussions of governing equations and turbulence models and their applications for predicting turbine blade heat transfer and film cooling, and turbine blade internal cooling.
Author: R.S. Amano Publisher: WIT Press ISBN: 1845649060 Category : Science Languages : en Pages : 253
Book Description
Due to the requirement for enhanced cooling technologies on modern gas turbine engines, advanced research and development has had to take place in field of thermal engineering. Among the gas turbine cooling technologies, impingement jet cooling is one of the most effective in terms of cooling effectiveness, manufacturability and cost. The chapters contained in this book describe research on state-of-the-art and advanced cooling technologies that have been developed, or that are being researched, with a variety of approaches from theoretical, experimental, and CFD studies. The authors of the chapters have been selected from some of the most active researchers and scientists on the subject. This is the first to book published on the topics of gas turbines and heat transfer to focus on impingement cooling alone.
Author: Bengt Sundén Publisher: Witpress ISBN: Category : Medical Languages : en Pages : 544
Book Description
This title presents and reflects current active research on various heat transfer topics and related phenomena in gas turbine systems. It begins with a general introduction to gas turbine heat transfer, before moving on to specific areas.
Author: Thomas Earl Dyson Publisher: ISBN: Category : Languages : en Pages : 576
Book Description
This study focused on the improvement of film cooling for gas turbine vanes using both computational and experimental techniques. The experimental component used a matched Biot number model to measure scaled surface temperature (overall effectiveness) distributions representative of engine conditions for two new configurations. One configuration consisted of a single row of holes on the pressure surface while the other used numerous film cooling holes over the entire vane including a showerhead. Both configurations used internal impingement cooling representative of a 1st vane. Adiabatic effectiveness was also measured. No previous studies had shown the effect of injection on the mean and fluctuating velocity profiles for the suction surface, so measurements were made at two locations immediately upstream of film cooling holes from the fully cooled cooling configuration. Different blowing conditions were evaluated. Computational tools are increasingly important in the design of advanced gas turbine engines and validation of these tools is required prior to integration into the design process. Two film cooling configurations were simulated and compared to past experimental work. Data from matched Biot number experiments was used to validate the overall effectiveness from conjugate simulations in addition to adiabatic effectiveness. A simulation of a single row of cooling holes on the suction side also gave additional insight into the interaction of film cooling jets with the thermal boundary layer. A showerhead configuration was also simulated. The final portion of this study sought to evaluate the performance of six RANS models (standard, realizable, and renormalization group k-[epsilon]; standard k-[omega]; k-[omega] SST; and Transition SST) with respect to the prediction of thermal boundary layers. The turbulent Prandtl number was varied to test a simple method for improvement of the thermal boundary layer predictions.
Author: Randall Paul Williams
Author: Randall Paul Williams
Author: John W. McClintic
Author: Chaitanya D Ghodke
Author: Je-Chin Han
Author: R.S. Amano
Author: Bengt Sundén
Author: Thomas Earl Dyson
Author: 
Author: Ramakrishnan Pudupatty
Author: