End-region Behavior of Precast, Prestressed Concrete I-girders Employing 0.7-inch Diameter Prestressing Strands PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download End-region Behavior of Precast, Prestressed Concrete I-girders Employing 0.7-inch Diameter Prestressing Strands PDF full book. Access full book title End-region Behavior of Precast, Prestressed Concrete I-girders Employing 0.7-inch Diameter Prestressing Strands by Jessica Lauren Salazar. Download full books in PDF and EPUB format.
Author: Jessica Lauren Salazar Publisher: ISBN: Category : Languages : en Pages : 352
Book Description
Pretensioned concrete girders are currently fabricated using 0.5- or 0.6-in. diameter prestressing strands. In recent years, however, it has become of interest to employ larger-diameter 0.7-in. diameter strands to reduce the number of strands and improve the efficiency of pretensioned concrete members. Such a transition requires a considerable initial investment that needs to be justified based on the benefits obtained. Furthermore, the use of 0.7-in. strands would increase the stresses within the end-region of pretensioned elements, which could lead to undesirable cracking and impact the serviceability of the girders. The work presented in this thesis consists of 1) a comprehensive parametric investigation to evaluate the benefits and limitations of using 0.7-in. strands in pretensioned bridge girders, and 2) a full-scale experimental study to investigate the behavior of pretensioned concrete girders with 0.7-in. strands at the time of prestress transfer. The parametric investigation was accomplished by designing thousands of bridge girders with different span lengths, concrete release strengths, and transverse spacings. The results showed that the most noticeable benefit of 0.7-in. strands over 0.6-in. strands was a reduction of up to 35 percent in the number of strands. However, the difference in the total weight of prestressing steel was insignificant. Increasing the release strength of concrete, at least to 7.5 ksi, was found essential to observe benefits in design aspects other than the number of strands. The experimental investigation involved the fabrication of two Tx46 and two Tx70 specimens at the Ferguson Structural Engineering Laboratory. All specimens employed 0.7-in. strands on a 2- by 2-in. grid and the standard detailing currently used for girders with smaller-diameter strands. The observed crack widths in the specimens upon prestress transfer did not exceed those typically observed in Tx-girders with smaller-diameter strands. Therefore, the use of 0.7-in. strands does not seem to trigger a need to modify the end-region detailing in Tx-girders. However, noticeably greater bursting and spalling forces were observed in the end regions of the specimens compared to the demands predicted by AASHTO LRFD provisions. The measured 24-hour transfer length from the specimens also exceeded estimates by AASHTO LRFD and ACI 318-14 provisions.
Author: Jessica Lauren Salazar Publisher: ISBN: Category : Languages : en Pages : 352
Book Description
Pretensioned concrete girders are currently fabricated using 0.5- or 0.6-in. diameter prestressing strands. In recent years, however, it has become of interest to employ larger-diameter 0.7-in. diameter strands to reduce the number of strands and improve the efficiency of pretensioned concrete members. Such a transition requires a considerable initial investment that needs to be justified based on the benefits obtained. Furthermore, the use of 0.7-in. strands would increase the stresses within the end-region of pretensioned elements, which could lead to undesirable cracking and impact the serviceability of the girders. The work presented in this thesis consists of 1) a comprehensive parametric investigation to evaluate the benefits and limitations of using 0.7-in. strands in pretensioned bridge girders, and 2) a full-scale experimental study to investigate the behavior of pretensioned concrete girders with 0.7-in. strands at the time of prestress transfer. The parametric investigation was accomplished by designing thousands of bridge girders with different span lengths, concrete release strengths, and transverse spacings. The results showed that the most noticeable benefit of 0.7-in. strands over 0.6-in. strands was a reduction of up to 35 percent in the number of strands. However, the difference in the total weight of prestressing steel was insignificant. Increasing the release strength of concrete, at least to 7.5 ksi, was found essential to observe benefits in design aspects other than the number of strands. The experimental investigation involved the fabrication of two Tx46 and two Tx70 specimens at the Ferguson Structural Engineering Laboratory. All specimens employed 0.7-in. strands on a 2- by 2-in. grid and the standard detailing currently used for girders with smaller-diameter strands. The observed crack widths in the specimens upon prestress transfer did not exceed those typically observed in Tx-girders with smaller-diameter strands. Therefore, the use of 0.7-in. strands does not seem to trigger a need to modify the end-region detailing in Tx-girders. However, noticeably greater bursting and spalling forces were observed in the end regions of the specimens compared to the demands predicted by AASHTO LRFD provisions. The measured 24-hour transfer length from the specimens also exceeded estimates by AASHTO LRFD and ACI 318-14 provisions.
Author: Roya Alirezaei Abyaneh Publisher: ISBN: Category : Languages : en Pages : 190
Book Description
Prestressed concrete girders are commonly fabricated with 0.5-in. (12.7-mm) or 0.6-in. (15.2-mm) diameter prestressing strands. Recent interest in the use of larger (0.7-in. (17.8-mm) diameter) strands has been driven by potential benefits associated with reduction of the required number of strands and fabrication time, or potential increases in the workable range of prestressed concrete girders (i.e., greater capacities and span capabilities). A limited number of experiments on full-scale specimens with 0.7-in. (17.8-mm) diameter strands have shown that the load-carrying capacity and strand transfer length of specimens with 0.7-in. (17.8-mm) diameter strands can be conservatively estimated using existing AASHTO LRFD provisions. However, performance at prestress transfer requires further investigation to ensure that application of the strands with standard 2-in. (50-mm) spacing and conventional concrete release strength does not increase the end-region cracking that is characteristic of prestressed girders. It must be verified that the development of such cracks does not stimulate anchorage-driven or premature shear failures prior to yielding of the shear reinforcement. Previous research lacks in monitoring of reinforcement stresses and evaluation of end-region cracking which has long been a durability concern. A reliable finite element model that captures the behavior of the specimen at prestress transfer with consideration of performance from construction stages, over the course of the service life, and up to the ultimate limit state can provide key insight into the suitability of using of 0.7-in. (17.8-mm) diameter strands. Further, it could serve as an economical tool for the investigation and proposal of efficient end-region reinforcing details to reduce concrete cracking and enhance durability. Finite element analyses of prestressed I-girder end-regions encompassing cracking and long-term creep- and shrinkage-induced damage, especially in girders fabricated with large diameter strands, have been limited. This research program assessed the limitations of 0.7-in. (17.8-mm) diameter strands at prestress transfer up to limit state response and investigated measures for enhancing the serviceability of the girders through finite element analyses using the commercial software, ATENA 3D. The finite element study was complemented with a full-scale experimental program which was used to validate the numerical results. This paper lays out a validated procedure for modeling the construction stages of prestressed girders and load testing. The model was then used as a tool for investigating alternative end-region reinforcement details for improved end-region serviceability. The most promising options are presented for consideration in further experimental studies and future implementation
Author: Alex Tyler Katz Publisher: ISBN: Category : Languages : en Pages : 500
Book Description
The majority of precast, pretensioned concrete elements are currently fabricated using 0.5- or 0.6-in. diameter prestressing strands. However, in recent years, potential benefits such as reduced fabrication costs and extended span capabilities have led to an interest in using larger-diameter 0.7-in. strands in the pretensioning industry. Such an increase in the diameter of strands might impact the shear strength of pretensioned girders due to the possibility of atypical failure modes that are not considered in current design provisions. An experimental program was conducted to study the effects of using 0.7-in. prestressing strands on the performance of precast, prestressed concrete I-girders under shear-critical loading conditions. Four full-scale pretensioned Texas bulb-tee girders (Tx-girders) employing 0.7-in. strands were fabricated and tested at Ferguson Structural Engineering Laboratory at the University of Texas at Austin. The mild steel reinforcement in the specimens was detailed according to standard drawings by the Texas Department of Transportation for girders employing 0.6-in. strands. The test program investigated the shear failure in girders with different concrete release strengths, overall member depths, shear span-to-depth ratios, and strand patterns. Analysis of the results revealed clear signs of atypical shear failure mechanisms in all specimens. Considerable strand slip was recorded at both ends of the specimens prior to peak load. In three of the specimens, the shear failure resulted in prominent horizontal cracks at the interface between the web and the bottom flange. However, all specimens demonstrated significant diagonal cracking prior to failure. Yielding of the stirrups was also confirmed in all specimens, indicating a shear-tension failure. The capacities of all specimens were conservatively estimated using the general procedure in AASHTO LRFD Bridge Design Specifications and the detailed method in ACI 318-14. The findings of this study reveal no concerns regarding the performance of existing design provisions in predicting the shear strength of Tx-girders that employ 0.7-in. diameter prestressing strands.
Author: Maher K. Tadros Publisher: Transportation Research Board ISBN: 0309118352 Category : Technology & Engineering Languages : en Pages : 76
Book Description
This report establishes a user's manual for the acceptance, repair, or rejection of precast/prestressed concrete girders with longitudinal web cracking. The report also proposes revisions to the AASHTO LRFD Bridge Design Specifications and provides recommendations to develop improved crack control reinforcement details for use in new girders. The material in this report will be of immediate interest to bridge engineers.
Author: Publisher: ISBN: Category : Languages : en Pages : 398
Book Description
Hundreds of prestressed concrete girders are used each year for building bridges. Prestressed concrete girders are preferred due to their effective span to depth ratios, and higher durability characteristics. The prestress transfer from the prestressing strands to concrete takes place at the girder ends. Characteristic cracks form in this end region during or immediately after detensioning. These cracks are more severe for the heavily prestressed deep bulb tee girders with thin webs, creating durability concerns. The problem can be structurally hazardous if cracks form paths for corrosion agents to reach the steel strands. Cracks in the bottom flange closer to the strands can easily form such paths. This research primarily focused on the analyses of nonlinear prestressed girder end regions to understand and recommend control methods for girder end cracking. The behavior of the pretensioned girder ends was simulated using nonlinear finite element analysis. The accuracy of the models was ensured by including the concrete nonlinearity, strain softening and stress redistribution upon cracking. The finite element modeling techniques were verified by test data. The principal tensile strain patterns correlating with cracking were used to explain the reasons behind each type of crack. Potential solutions to control end cracking were examined via finite element models. The impact of end zone reinforcement pattern, debonding of strands, strand cutting order, draped strand pattern, and lifting of the girder on the cracks were evaluated. The reduction in principal tensile strains associated with cracking was quantified for each crack control method. The analysis results showed that debonding strands can effectively control cracking. Other methods improve the end zone strains however are not sufficient to eliminate cracking alone. Combining the solutions involving debonding, extra reinforcing in the web, and a controlled sequence of strand detensioning should lead to elimination of end cracking.
Author: Richard A. Miller (Professional engineer) Publisher: Transportation Research Board ISBN: 0309087937 Category : Concrete beams Languages : en Pages : 202
Book Description
Introduction and Research Approach -- Findings -- Interpretation, Appraisal, and Application -- Interpretation, Appraisal, and Application -- References -- Appendixes.
Author: Alistair Thornton Longshaw Publisher: ISBN: Category : Languages : en Pages : 270
Book Description
Although 0.5- and 0.6-in. diameter strands are commonly used in the prestressing industry, there is a growing interest in the implementation of 0.7-in. diameter strands. However, the greater prestressing force induced poses several potential implications, particularly when the strands are placed on a 2- by 2-in. grid. One such issue is end-region cracking, an occurrence that is common in pretensioned girders, regardless of strand size. These cracks tend to grow in width, length, and number over time due to time-dependent effects such as shrinkage or creep. Additionally, the cracks tend to close under an applied load when placed in a service-state condition. End-region crack widths are often used to evaluate the condition of pretensioned girders, so a thorough understanding of the development of these cracks is essential to applying crack width criteria appropriately. A multifaceted experimental program was conducted at the Ferguson Structural Engineering Laboratory at the University of Texas at Austin. A series of seven Texas bulb-tee girders employing 0.7-in. diameter strands was fabricated, monitored, and load tested under shear-critical conditions. The end-region cracks of three specimens were measured immediately after prestress transfer and monitored for at least 28 days, showing that the crack widths grew significantly over time. This growth corresponded closely with the shrinkage strain measured at midspan of each girder, indicating that shrinkage is the primary cause of end-region crack growth. A significant amount of transverse reinforcement is placed in end-regions to restrict cracks immediately after prestress transfer, but this same reinforcement also provides a large amount of restraint against concrete shrinkage, exacerbating crack growth. End-region cracks were also measured during the shear-critical load test for two specimens. Although they closed in a linear manner, they were not completely closed at an expected service load. At ultimate load, the cracks never closed entirely, as the imperfect concrete surfaces bore against each other shortly after initial diagonal shear cracking. Based on both of these findings, future end-region crack widths can be more accurately predicted from any point in the lifespan of a pretensioned girder, allowing for more appropriate applications of permissible crack width limits.
Author: Maher K. Tadros Publisher: Transportation Research Board ISBN: 030908766X Category : Technology & Engineering Languages : en Pages : 73
Book Description
"The HCM includes three printed volumes (Volumes 1-3) that can be purchased from the Transportation Research Board in print and electronic formats. Volume 4 is a free online resource that supports the rest of the manual. It includes: Supplemental chapters 25-38, providing additional details of the methodologies described in the Volume 1-3 chapters, example problems, and other resources; A technical reference library providing access to a significant portion of the research supporting HCM methods; Two applications guides demonstrating how the HCM can be applied to planning-level analysis and a variety of traffic operations applications; Interpretations, updates, and errata for the HCM (as they are developed);A discussion forum allowing HCM users to ask questions and collaborate on HCM-related matters; and Notifications of chapter updates, active discussions, and more via an optional e-mail notification feature."--Publisher.
Author: Jessica Lauren Salazar
Author: Jessica Lauren Salazar
Author: Roya Alirezaei Abyaneh
Author: Hossein Yousefpour
Author: Alex Tyler Katz
Author: Maher K. Tadros
Author: 
Author: Richard A. Miller (Professional engineer)
Author: Alistair Thornton Longshaw
Author: Maher K. Tadros
Author: Maher K. Tadros