Author: W. C. ThurberPublisher:
ISBN:
Category : Nuclear reactions
Languages : en
Pages : 58
Book Description
Dispersions of Uranium Carbides in Aluminum Plate-type Research Reactor Fuel Elements
Author: W. C. ThurberPublisher:
ISBN:
Category : Nuclear reactions
Languages : en
Pages : 58
Book Description
Dispersions of Uranium in Aluminum Plate-type Research Reactor Fuel Elements
Author: William Clarence ThurberPublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
DISPERSIONS OF URANIUM CARBIDES IN ALUMINUM PLATE-TYPE RESEARCH REACTOR FUEL ELEMENTS.
Author: Publisher:
ISBN:
Category :
Languages : en
Pages :
Book Description
The technical feasibility of employing uranium carbide aluminun dispersions in aluminum-base research reactor fuel elements was investigated This study was motivated by the need to obtain higher uranium loadings in these fuel elements. Although toe MTR-type unit, containing a 13 18 wt% U-Al alloy is a proven reactor component, fabrication problems of considerable magnitude arise when attempts are made to increase the uranium investment in the alloy to more than 25 wt.%. Au approach to these fabrication difficulties is to select a compound with significantly higher density tban UAl4 or UAl3 compounds of the alloy system which when dispersed in aluminum powder, will reduce the volume occupied by the brittle, fissile phase. The uranium carbides, with densities ranging from 11.68 to 13.63 g/cm3), appear to be suited for this application and were selected for development as a fuel material for aluminum-base dispersions. Studies were conducted at 580 to 620 deg C to determine the chemical compatibility of carbides with aluminum in sub-size cold- pressed comparts as well as in full-size fabricated fuel plates. Procedures were also developed to prepare uranium carbides, homogernously disperse the compounds in aluminum, roll clad the dispersions to form composite plates, and braze the plates into fuel assemblies. Corrosion tests of the fuel material were conducted in 20 and 60 deg C water to determine the integrity of the fuel material in the event of sin inadventent cladding failure. In addition, specimens were prepared to evaluate penformance under extensive irradiation Prior to studying the uranium carbide-aluminum system, methods for preparing the carbides were investigated. Are melting uranium and carnon was satisfactory for obtaining small quantities of various carbides. Later, reaction of graphite with UO2 was successfully employed in the preparation of large quantities of UC2, Studies of the chemical compatibility of cold-pressed compacts containing 50 wt% uranium carbide dispersed in aluminum revealed a marked trend toward stebifity as the carbon content of the uranium carbide increased from 446 to 9.20% C. Severe volume increases occurred in monocarbide dispersions with attendant formation of large quantities of the uranium-allumnim inter-metallic compounds. Dicarbide dispersions, on the other band, exhibited negligible reaction with aluminum after extended periods at 580 and 620 deg C. However, it was demonstrated that hydrogen can promote a reaction in UC2-Al compacts. The hydrogen appears to reduce the UC2 to UC which can subsequently react with aluminum producing the previously noted deleterious effects. A growth study at 605 deg C of composite fuel plates containing 59 wt.% UC2 revealed insignificant changes within processing periods envisioned for fuel element processing. However, plate elongations as high as 2.5% were observed after 100 hr at this temperature. Severe blistering which occurred on fuel plates fabricated in the initial stages of the investigation was attributed to gaseous hydrocarbons, and the condition was ellminated by vacuum degasification of cold-pressed compacts. With the exception of the degasification requirement, procedures for manufacturing UC- bearing fuel elements were identical to those specified for the Geneva Conference Reactor fuel elements. Dispersions of uranium dicarbide corroded catastrophically in 20 and 60 deg C water, thus limiting the application of this material However, spocimens were prepared and insented in the MTR to evaluate the irradiation behavior of this fuel because of its potential application in onganic- cooled reactors. (auth).
Nuclear Science Abstracts
Author: An Evaluation of the Uranium Contamination on the Surfaces of Alclad Uranium-aluminum Alloy Research Reactor Fuel Plates
Author: R. J. BeaverPublisher:
ISBN:
Category : Aluminum-uranium alloys
Languages : en
Pages : 38
Book Description
Specifications and Procedures Used in Manufacturing U$sub 3$O$sub 8$- Aluminum Dispersion Fuel Elements for Core I of the Puerto Rico Research Reactor
Author: Publisher:
ISBN:
Category :
Languages : en
Pages :
Book Description
A thin plate-type element containing a dispersion of 20% enriched U/sub 3/O/sub 8/ was developed and successfully used in the 5-Mw pool-type research reactor at the Puerto Rico Nuclear Center. The underlying criteria that guided the design are presented. The technological factors, such as compatibility, corrosion resistance, and irradiation behavior, which led to the selection of U/ sub 3/O/sub 8/ as the fissile compound and aluminum as the cladding and matrix material, are reviewed. The fabrication procedures developed and adopted for manufacturing the component are presented. The scheme involves incorporation of 55 wt% U/sub 3/O/sub 8/ into aluminum compacts by powder metallurgy techniques, preparation of composite fuel plates by roll cladding, assembly of fuel plates into an integral unit by either the roll-swaging or pinning techniques, and corrosion protection of the element by an anodizing treatment to increase service life. Quality control measures adopted to ensure dimensional tolerances are described. Mechanical joining proved to be an economical method for assembling the pool-type fuel elements within dimensional specifications. (auth).
Dispersion Fuel Elements
Author: Abe Noel HoldenPublisher:
ISBN:
Category : Nuclear fuel elements
Languages : en
Pages : 276
Book Description
Nuclear Regulatory Commission Issuances
Author: U.S. Nuclear Regulatory CommissionPublisher:
ISBN:
Category : Nuclear energy
Languages : en
Pages : 950
Book Description
Author: 
Author: