An Evaluation of Turbulence Models for the Numerical Study of Forced and Natural Convective Flow in Atria PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download An Evaluation of Turbulence Models for the Numerical Study of Forced and Natural Convective Flow in Atria PDF full book. Access full book title An Evaluation of Turbulence Models for the Numerical Study of Forced and Natural Convective Flow in Atria by . Download full books in PDF and EPUB format.
Author: Publisher: ISBN: Category : Languages : en Pages :
Book Description
A demand for methods that can be used in the numerical analysis of three dimensional air flow in large buildings has developed as more buildings are being designed with large atriums using a solar loading that leads to complex flow. The flow in such buildings is almost always turbulent which means that turbulence models that are accurate but which do not require undue computer resources have to be selected. As a result, a numerical study of natural convective heat transfer and turbulent flows in large atria, specifically part of the Atria in the EV building at Concordia University, has been completed. Experimental work on turbulence modeling and atria design has been studied and compared with the numerical results obtained here to gain confidence in the modeling techniques used in the study. The flow has been assumed to be steady, and the Boussinesq approximation has been used. The governing equations have been numerically solved using the CFD solver FLUENT. The three-dimensional air flow in the Concordia-like atria used the following parameters: forced flow vent inlet angle; forced flow vent velocity; date and time (for solar radiation purposes). The case with adiabatic floor and ceiling conditions was examined and compared to the case with isothermal floor and ceiling conditions. Several models were studied to compare the effect of turbulent modeling in the atria, including the following: (1) K-Epsilon; (2) K-Omega; (3) Detached Eddy Simulation (DES) model; (4) Large Eddy Simulation (LES) model. Further study was completed after it was noted the flow was completely based on natural convection when the velocity of the inlet flow was set to zero. In addition, experimental results were available and this situation was modeled using similar parameters to the work explained above. Comparing these results supported the accuracy of the work done on the Concordia Atrium. Experimental work on the Annex 26 Atrium in Yokohama Japan was also compared to numerical results to g.
Author: Publisher: ISBN: Category : Languages : en Pages :
Book Description
A demand for methods that can be used in the numerical analysis of three dimensional air flow in large buildings has developed as more buildings are being designed with large atriums using a solar loading that leads to complex flow. The flow in such buildings is almost always turbulent which means that turbulence models that are accurate but which do not require undue computer resources have to be selected. As a result, a numerical study of natural convective heat transfer and turbulent flows in large atria, specifically part of the Atria in the EV building at Concordia University, has been completed. Experimental work on turbulence modeling and atria design has been studied and compared with the numerical results obtained here to gain confidence in the modeling techniques used in the study. The flow has been assumed to be steady, and the Boussinesq approximation has been used. The governing equations have been numerically solved using the CFD solver FLUENT. The three-dimensional air flow in the Concordia-like atria used the following parameters: forced flow vent inlet angle; forced flow vent velocity; date and time (for solar radiation purposes). The case with adiabatic floor and ceiling conditions was examined and compared to the case with isothermal floor and ceiling conditions. Several models were studied to compare the effect of turbulent modeling in the atria, including the following: (1) K-Epsilon; (2) K-Omega; (3) Detached Eddy Simulation (DES) model; (4) Large Eddy Simulation (LES) model. Further study was completed after it was noted the flow was completely based on natural convection when the velocity of the inlet flow was set to zero. In addition, experimental results were available and this situation was modeled using similar parameters to the work explained above. Comparing these results supported the accuracy of the work done on the Concordia Atrium. Experimental work on the Annex 26 Atrium in Yokohama Japan was also compared to numerical results to g.
Author: Akhyar Publisher: Springer Nature ISBN: 9811607362 Category : Technology & Engineering Languages : en Pages : 525
Book Description
This book gathers a selection of peer-reviewed papers presented at the 2nd International Conference on Experimental and Computational Mechanics in Engineering (ICECME 2020), held as a virtual conference and organized by Universitas Syiah Kuala, Banda Aceh, Indonesia, on 13–14 October 2020. The contributions, prepared by international scientists and engineers, cover the latest advances in computational mechanics, metallurgy and material science, energy systems, manufacturing processing systems, industrial and system engineering, biomechanics, artificial intelligence, micro/nano-engineering, micro-electro-mechanical system, machine learning, mechatronics, and engineering design. The book is intended for academics, including graduate students and researchers, as well as industrial practitioners working in the areas of experimental and computational mechanics.
Author: Tomás Chacón Rebollo Publisher: Springer ISBN: 1493904558 Category : Mathematics Languages : en Pages : 530
Book Description
With applications to climate, technology, and industry, the modeling and numerical simulation of turbulent flows are rich with history and modern relevance. The complexity of the problems that arise in the study of turbulence requires tools from various scientific disciplines, including mathematics, physics, engineering and computer science. Authored by two experts in the area with a long history of collaboration, this monograph provides a current, detailed look at several turbulence models from both the theoretical and numerical perspectives. The k-epsilon, large-eddy simulation and other models are rigorously derived and their performance is analyzed using benchmark simulations for real-world turbulent flows. Mathematical and Numerical Foundations of Turbulence Models and Applications is an ideal reference for students in applied mathematics and engineering, as well as researchers in mathematical and numerical fluid dynamics. It is also a valuable resource for advanced graduate students in fluid dynamics, engineers, physical oceanographers, meteorologists and climatologists.
Author: W. Rodi Publisher: Elsevier ISBN: 008053094X Category : Mathematics Languages : en Pages : 1029
Book Description
Turbulence is one of the key issues in tackling engineering flow problems. As powerful computers and accurate numerical methods are now available for solving the flow equations, and since engineering applications nearly always involve turbulence effects, the reliability of CFD analysis depends increasingly on the performance of the turbulence models. This series of symposia provides a forum for presenting and discussing new developments in the area of turbulence modelling and measurements, with particular emphasis on engineering-related problems. The papers in this set of proceedings were presented at the 5th International Symposium on Engineering Turbulence Modelling and Measurements in September 2002. They look at a variety of areas, including: Turbulence modelling; Direct and large-eddy simulations; Applications of turbulence models; Experimental studies; Transition; Turbulence control; Aerodynamic flow; Aero-acoustics; Turbomachinery flows; Heat transfer; Combustion systems; Two-phase flows. These papers are preceded by a section containing 6 invited papers covering various aspects of turbulence modelling and simulation as well as their practical application, combustion modelling and particle-image velocimetry.
Author: Tuncer Cebeci Publisher: Springer Science & Business Media ISBN: 9783540402886 Category : Science Languages : en Pages : 140
Book Description
After a brief review of the more popular turbulence models, the author presents and discusses accurate and efficient numerical methods for solving the boundary-layer equations with turbulence models based on algebraic formulas (mixing length, eddy viscosity) or partial-differential transport equations. A computer program employing the Cebeci-Smith model and the k-e model for obtaining the solution of two-dimensional incompressible turbulent flows without separation is discussed in detail and is presented in the accompanying CD.
Author: Jean Piquet Publisher: Springer Science & Business Media ISBN: 3662035596 Category : Technology & Engineering Languages : en Pages : 767
Book Description
obtained are still severely limited to low Reynolds numbers (about only one decade better than direct numerical simulations), and the interpretation of such calculations for complex, curved geometries is still unclear. It is evident that a lot of work (and a very significant increase in available computing power) is required before such methods can be adopted in daily's engineering practice. I hope to l"Cport on all these topics in a near future. The book is divided into six chapters, each· chapter in subchapters, sections and subsections. The first part is introduced by Chapter 1 which summarizes the equations of fluid mechanies, it is developed in C~apters 2 to 4 devoted to the construction of turbulence models. What has been called "engineering methods" is considered in Chapter 2 where the Reynolds averaged equations al"C established and the closure problem studied (§1-3). A first detailed study of homogeneous turbulent flows follows (§4). It includes a review of available experimental data and their modeling. The eddy viscosity concept is analyzed in §5 with the l"Csulting ~alar-transport equation models such as the famous K-e model. Reynolds stl"Css models (Chapter 4) require a preliminary consideration of two-point turbulence concepts which are developed in Chapter 3 devoted to homogeneous turbulence. We review the two-point moments of velocity fields and their spectral transforms (§ 1), their general dynamics (§2) with the particular case of homogeneous, isotropie turbulence (§3) whel"C the so-called Kolmogorov's assumptions are discussed at length.
Author: Weiran Xu Publisher: ISBN: Category : Languages : en Pages : 170
Book Description
It is important to predict indoor environment in order to design thermally comfortable and healthy indoor spaces. Heating, Ventilating and Air Conditioning (HVAC) design engineers and architects widely use the Computational Fluid Dynamics (CFD) technique for indoor environment predictions. The CFD technique requires a turbulence model to correctly calculate indoor air distribution. However, the currently available turbulence models in the literature are either inaccurate or inefficient for the indoor environment predictions. To solve the problem, this thesis proposes two two-layer turbulence models and a zero-equation turbulence model. The two-layer models use a one-equation (k) model for the near wall region and the "standard" k -£ model in the outer region. The zero-equation model calculates turbulent viscosity based on local velocity and a length-scale. The near wall models have been developed with the aid of the data of natural and forced convection flows by Direct Numerical Simulation (DNS), while the zero-equation model has been proposed empirically. One of the two-layer turbulence models is used for predicting natural convection in rooms. The other two-layer model and the zero-equation model can be used to predict forced, natural, and mixed convection in rooms. These three new models have been applied to predict different types of indoor airflows. The corresponding DNS or experimental data were used to validate the models. This study concludes that the two-layer models can predict airflows most accurately, better than many k -E models. The computing cost is significantly lower than that of the low Reynolds number k-E models and is only slightly higher than that of the "standard" k-E models. The zero-equation model is at least ten times faster than the "standard" k-E model and it is numerically stable and can predict indoor airflow with acceptable accuracy.
Author: G. Biswas Publisher: CRC Press ISBN: 9780849310140 Category : Technology & Engineering Languages : en Pages : 478
Book Description
This book allows readers to tackle the challenges of turbulent flow problems with confidence. It covers the fundamentals of turbulence, various modeling approaches, and experimental studies. The fundamentals section includes isotropic turbulence and anistropic turbulence, turbulent flow dynamics, free shear layers, turbulent boundary layers and plumes. The modeling section focuses on topics such as eddy viscosity models, standard K-E Models, Direct Numerical Stimulation, Large Eddy Simulation, and their applications. The measurement of turbulent fluctuations experiments in isothermal and stratified turbulent flows are explored in the experimental methods section. Special topics include modeling of near wall turbulent flows, compressible turbulent flows, and more.
Author: Manuel D. Salas Publisher: Springer Science & Business Media ISBN: 9401147248 Category : Science Languages : en Pages : 385
Book Description
Turbulence modeling both addresses a fundamental problem in physics, 'the last great unsolved problem of classical physics,' and has far-reaching importance in the solution of difficult practical problems from aeronautical engineering to dynamic meteorology. However, the growth of supercom puter facilities has recently caused an apparent shift in the focus of tur bulence research from modeling to direct numerical simulation (DNS) and large eddy simulation (LES). This shift in emphasis comes at a time when claims are being made in the world around us that scientific analysis itself will shortly be transformed or replaced by a more powerful 'paradigm' based on massive computations and sophisticated visualization. Although this viewpoint has not lacked ar ticulate and influential advocates, these claims can at best only be judged premature. After all, as one computational researcher lamented, 'the com puter only does what I tell it to do, and not what I want it to do. ' In turbulence research, the initial speculation that computational meth ods would replace not only model-based computations but even experimen tal measurements, have not come close to fulfillment. It is becoming clear that computational methods and model development are equal partners in turbulence research: DNS and LES remain valuable tools for suggesting and validating models, while turbulence models continue to be the preferred tool for practical computations. We believed that a symposium which would reaffirm the practical and scientific importance of turbulence modeling was both necessary and timely.
Author: Paul Durbin Publisher: Elsevier ISBN: 0128208902 Category : Technology & Engineering Languages : en Pages : 554
Book Description
Advanced Approaches in Turbulence: Theory, Modeling, Simulation and Data Analysis for Turbulent Flows focuses on the updated theory, simulation and data analysis of turbulence dealing mainly with turbulence modeling instead of the physics of turbulence. Beginning with the basics of turbulence, the book discusses closure modeling, direct simulation, large eddy simulation and hybrid simulation. The book also covers the entire spectrum of turbulence models for both single-phase and multi-phase flows, as well as turbulence in compressible flow. Turbulence modeling is very extensive and continuously updated with new achievements and improvements of the models. Modern advances in computer speed offer the potential for elaborate numerical analysis of turbulent fluid flow while advances in instrumentation are creating large amounts of data. This book covers these topics in great detail. Covers the fundamentals of turbulence updated with recent developments Focuses on hybrid methods such as DES and wall-modeled LES Gives an updated treatment of numerical simulation and data analysis
Author: 
Author: 
Author: Akhyar
Author: Tomás Chacón Rebollo
Author: W. Rodi
Author: Tuncer Cebeci
Author: Jean Piquet
Author: Weiran Xu
Author: G. Biswas
Author: Manuel D. Salas
Author: Paul Durbin