Three-dimensional Aspects of Plasticity-induced Fatigue Crack Closure PDF Download

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 40

View

Book Description

Author: Jeffrey David Skinner
Publisher:
ISBN:
Category : Finite element method
Languages : en
Pages :

View

Book Description
[3] The finite element predicted opening levels were in all cases significantly lower than those reported experimentally, however, similar trends in both crack opening level profile along the crack front, and opening level variations with crack growth were shown.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :

View

Book Description
Elastic-plastic finite element analyses were performed to predict the crack opening level profiles in semi-elliptical surface cracks. A script was written to use the commercial finite element code ANSYS to predict opening levels in cracked geometries. The functionality of the scripts was verified by comparing predicted opening levels in two and three-dimensional center-cracked geometries to experimental results. In addition, a parameter study was performed in which various aspects of the modeling routine were modified. This included a mesh refinement study as well as a study into the effect of a strain hardening material. The main focus of the current research, however, is to compare finite element predicted opening levels with published opening levels determined experimentally. Due to the complexities and long run-times involved with these models, no attempt was made at growing the cracks from initial length to final length. Instead, discrete crack lengths at which experimental opening levels were published were instead used. Also, no attempt was made to predict the crack aspect ratio evolution. The finite element predicted opening levels were in all cases significantly lower than those reported experimentally, however, similar trends in both crack opening level profile along the crack front, and opening level variations with crack growth were shown.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :

View

Book Description
Finite element analyses are frequently used to model growing fatigue cracks and the associated plasticity-induced crack closure. Two-dimensional, elastic-perfectly plastic finite element analyses of middle-crack tension (M(T)), bend (SEB), and compact tension (C(T)) geometries were conducted to study fatigue crack closure and to calculate the crack opening values under plane-strain and plane-stress conditions. The loading was selected to give the same maximum stress intensity factor in both geometries, and thus similar initial forward plastic zone sizes. Mesh refinement studies were performed on all geometries with various element types. For the C(T) geometry, negligible crack opening loads under plane-strain conditions were observed. In contrast, for the M(T) specimen, the plane-strain crack opening stresses were found to be significantly larger. This difference was shown to be a consequence of in-plane constraint. Under plane-stress conditions, it was found that the in-plane constraint has negligible effect, such that the opening values are approximately the same for the C(T), SEB, and M(T) specimens. Next, the crack opening values of the C(T), SEB and M(T) specimens were compared under various stress levels and load ratios. The effect of a highly refined mesh on crack opening values was noted and significantly lower crack opening values than those reported in literature were found. A new methodology is presented to calculate crack opening values in planar geometries using the crack surface nodal force distribution under minimum loading as determined from finite element analyses. The calculated crack opening values are compared with values obtained using finite element analysis and more conventional crack opening assessment methodologies. It is shown that the new method is independent of loading increment, integration method (normal and reduced integration), and crack opening assessment location. The compared opening values were in good agreement with strip-yield.

Author: RH. Dodds
Publisher:
ISBN:
Category : Contact
Languages : en
Pages : 19

View

Book Description
In ductile metals, plasticity-induced closure of fatigue cracks often retards significantly measured crack growth rates in the Paris regime and contributes strongly to the observed R-ratio effect in experimental data. This work describes a similarity scaling relationship based on the 3D small-scale yielding framework wherein the thickness, B, defines the only geometric length-scale of the model. Dimensional analysis suggests a scaling relationship for the crack opening loads relative to the maximum cyclic loads (Kop/Kmax) governed by the non-dimensional load parameter ̄K=Kmax/?0 ?B, i.e., a measure of the in-plane plastic zone size normalized by the thickness. Both Kop and Kmax refer to remotely applied values of the mode I stress-intensity factor. Large-scale, 3D finite element analyses described here demonstrate that Kop/Kmax values vary strongly across the crack front in thin sheets but remain unchanged when Kmax, B, and ?0 vary to maintain ̄K = constant. The paper also includes results to demonstrate that the scaling relationship holds for non-zero values of the T-stress (which affect the Kop/Kmax values) and for an overload interspersed in the otherwise constant amplitude cycles. The present results focus on R = Kmin/Kmax = 0 loading, although the scaling relationship has been demonstrated to hold for other R > 0 loadings as well. The new similarity scaling relationship makes possible more realistic estimates of crack closure loads for a very wide range of practical conditions from just a few analyses of the type described here.

Author: R. Craig McClung
Publisher: ASTM International
ISBN: 0803126115
Category : Fracture mechanics
Languages : en
Pages : 487

View

Book Description

Author: Wolf Elber
Publisher: ASTM International
ISBN: 0803109962
Category : Fracture mechanics
Languages : en
Pages : 671

View

Book Description

Author: Steven R. Daniewicz
Publisher: ASTM International
ISBN: 0803134878
Category : Fatigue
Languages : en
Pages : 591

View

Book Description

Author: K.S. Ravichandran
Publisher: Elsevier
ISBN: 0080569706
Category : Technology & Engineering
Languages : en
Pages : 511

View

Book Description
This book contains the fully peer-reviewed papers presented at the Third Engineering Foundation Conference on Small Fatigue Cracks, held under the chairmanship of K.S. Ravichandran and Y. Murakami during December 6-11, 1998, at the Turtle Bay Hilton, Oahu, Hawaii. This book presents a state-of-the-art description of the mechanics, mechanisms and applications of small fatigue cracks by most of the world's leading experts in this field. Topics ranging from the mechanisms of crack initiation, small crack behavior in metallic, intermetallic, ceramic and composite materials, experimental measurement, mechanistic and theoretical models, to the role of small cracks in fretting fatigue and the application of small crack results to the aging aircraft and high-cycle fatigue problems, are covered.

Author: Stephen Riley Johnston
Publisher:
ISBN:
Category : Aluminum alloys
Languages : en
Pages :

View

Book Description
This thesis discusses plasticity-induced crack closure based finite element simulations of small fatigue cracks in three dimensions utilizing crystal plasticity theory. Previously, modeling has been performed in two dimensions using a double-slip crystal plasticity material model. The goal of this work is to extend that research using a full three-dimensional FCC crystal plasticity material model implementation that accounts for all twelve FCC slip systems. Discussions of Python scripts that were written to perform analyses with the commercial finite element code ABAQUS are given. A detailed description of the modeling methodology is presented along with results for single crystals and bicrystals. The results are compared with finite element and experimental results from the literature. A discussion of preliminary work for the analysis of crack growth around an intermetallic particle is also presented.