Space Shuttle Main Engine Structural Analysis and Data Reduction/Evaluation. Volume 2 PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Space Shuttle Main Engine Structural Analysis and Data Reduction/Evaluation. Volume 2 PDF full book. Access full book title Space Shuttle Main Engine Structural Analysis and Data Reduction/Evaluation. Volume 2 by National Aeronautics and Space Administration (NASA). Download full books in PDF and EPUB format.
Author: National Aeronautics and Space Administration (NASA) Publisher: Createspace Independent Publishing Platform ISBN: 9781722755027 Category : Languages : en Pages : 86
Book Description
The high-pressure oxidizer turbopump (HPOTP) consists of two centrifugal pumps, on a common shaft, that are directly driven by a hot-gas turbine. Pump shaft axial thrust is balanced in that the double-entry main inducer/impeller is inherently balanced and the thrusts of the preburner pump and turbine are nearly equal but opposite. Residual shaft thrust is controlled by a self-compensating, non-rubbing, balance piston. Shaft hang-up must be avoided if the balance piston is to perform properly. One potential cause of shaft hang-up is contact between the Phase 2 bearing support and axial spring cartridge of the HPOTP main pump housing. The status of the bearing support/axial spring cartridge interface is investigated under current loading conditions. An ANSYS version 4.3, three-dimensional, finite element model was generated on Lockheed's VAX 11/785 computer. A nonlinear thermal analysis was then executed on the Marshall Space Flight Center Engineering Analysis Data System (EADS). These thermal results were then applied along with the interference fit and bolt preloads to the model as load conditions for a static analysis to determine the gap status of the bearing support/axial spring cartridge interface. For possible further analysis of the local regions of HPOTP main pump housing assembly, detailed ANSYS submodels were generated using I-DEAS Geomod and Supertab (Appendix A). Sisk, Gregory A. Unspecified Center...
Author: National Aeronautics and Space Administration (NASA) Publisher: Createspace Independent Publishing Platform ISBN: 9781722755027 Category : Languages : en Pages : 86
Book Description
The high-pressure oxidizer turbopump (HPOTP) consists of two centrifugal pumps, on a common shaft, that are directly driven by a hot-gas turbine. Pump shaft axial thrust is balanced in that the double-entry main inducer/impeller is inherently balanced and the thrusts of the preburner pump and turbine are nearly equal but opposite. Residual shaft thrust is controlled by a self-compensating, non-rubbing, balance piston. Shaft hang-up must be avoided if the balance piston is to perform properly. One potential cause of shaft hang-up is contact between the Phase 2 bearing support and axial spring cartridge of the HPOTP main pump housing. The status of the bearing support/axial spring cartridge interface is investigated under current loading conditions. An ANSYS version 4.3, three-dimensional, finite element model was generated on Lockheed's VAX 11/785 computer. A nonlinear thermal analysis was then executed on the Marshall Space Flight Center Engineering Analysis Data System (EADS). These thermal results were then applied along with the interference fit and bolt preloads to the model as load conditions for a static analysis to determine the gap status of the bearing support/axial spring cartridge interface. For possible further analysis of the local regions of HPOTP main pump housing assembly, detailed ANSYS submodels were generated using I-DEAS Geomod and Supertab (Appendix A). Sisk, Gregory A. Unspecified Center...
Author: National Aeronautics and Space Adm Nasa Publisher: ISBN: 9781730942747 Category : Languages : en Pages : 86
Book Description
The high-pressure oxidizer turbopump (HPOTP) consists of two centrifugal pumps, on a common shaft, that are directly driven by a hot-gas turbine. Pump shaft axial thrust is balanced in that the double-entry main inducer/impeller is inherently balanced and the thrusts of the preburner pump and turbine are nearly equal but opposite. Residual shaft thrust is controlled by a self-compensating, non-rubbing, balance piston. Shaft hang-up must be avoided if the balance piston is to perform properly. One potential cause of shaft hang-up is contact between the Phase 2 bearing support and axial spring cartridge of the HPOTP main pump housing. The status of the bearing support/axial spring cartridge interface is investigated under current loading conditions. An ANSYS version 4.3, three-dimensional, finite element model was generated on Lockheed's VAX 11/785 computer. A nonlinear thermal analysis was then executed on the Marshall Space Flight Center Engineering Analysis Data System (EADS). These thermal results were then applied along with the interference fit and bolt preloads to the model as load conditions for a static analysis to determine the gap status of the bearing support/axial spring cartridge interface. For possible further analysis of the local regions of HPOTP main pump housing assembly, detailed ANSYS submodels were generated using I-DEAS Geomod and Supertab (Appendix A). Sisk, Gregory A. Unspecified Center...
Author: National Aeronautics and Space Administration (NASA) Publisher: Createspace Independent Publishing Platform ISBN: 9781722755317 Category : Languages : en Pages : 100
Book Description
The analysis performed on the Space Shuttle Main Engine (SSME) High Pressure Fuel Turbopump (HPFTP) inlet housings is summarized. Three DIAL finite element models were build to aid in assessing the structural life of the welds and fillets at the vanes. Complete results are given. Pool, Kirby V. Unspecified Center...
Author: National Aeronautics and Space Administration (NASA) Publisher: Createspace Independent Publishing Platform ISBN: 9781722788834 Category : Languages : en Pages : 32
Book Description
The analysis performed on the Main Injector LOX Inlet Assembly located on the Space Shuttle Main Engine is summarized. An ANSYS finite element model of the inlet assemably was built and executed. Static stress analysis was also performed. Violett, Rebeca S. Unspecified Center NAS8-37282...
Author: National Aeronautics and Space Administration (NASA) Publisher: Createspace Independent Publishing Platform ISBN: 9781722754990 Category : Languages : en Pages : 86
Book Description
Using the ANSYS finite element program, a global model of the aft skirt and a detailed nonlinear model of the failure region was made. The analysis confirmed the area of failure in both STA-2B and STA-3 tests as the forging heat affected zone (HAZ) at the aft ring centerline. The highest hoop strain in the HAZ occurs in this area. However, the analysis does not predict failure as defined by ultimate elongation of the material equal to 3.5 percent total strain. The analysis correlates well with the strain gage data from both the Wyle influence test of the original design aft sjirt and the STA-3 test of the redesigned aft skirt. it is suggested that the sensitivity of the failure area material strength and stress/strain state to material properties and therefore to small manufacturing or processing variables is the most likely cause of failure below the expected material ultimate properties. Berry, David M. and Stansberry, Mark Unspecified Center...
Author: National Aeronautics and Space Administration (NASA) Publisher: Createspace Independent Publishing Platform ISBN: 9781722755201 Category : Languages : en Pages : 54
Book Description
The model generation and structural analysis performed for the High Pressure Oxidizer Turbopump (HPOTP) preburner pump volute housing located on the main pump end of the HPOTP in the space shuttle main engine are summarized. An ANSYS finite element model of the volute housing was built and executed. A static structural analysis was performed on the Engineering Analysis and Data System (EADS) Cray-XMP supercomputer Shannon, Robert V., Jr. Unspecified Center...
Author: National Aeronautics and Space Administration (NASA) Publisher: Createspace Independent Publishing Platform ISBN: 9781722788650 Category : Languages : en Pages : 42
Book Description
The analysis performed on the High Pressure Oxidizer Turbopump (HPOTP) preburner pump bearing assembly located on the Space Shuttle Main Engine (SSME) is summarized. An ANSYS finite element model for the inlet assembly was built and executed. Thermal and static analyses were performed. Power, Gloria B. and Violett, Rebeca S. Unspecified Center NAS8-37282...
Author: National Aeronautics and Space Administration (NASA)
Author: National Aeronautics and Space Administration (NASA)
Author: National Aeronautics and Space Adm Nasa
Author: National Aeronautics and Space Administration (NASA)
Author: National Aeronautics and Space Administration (NASA)
Author: 
Author: 
Author: 
Author: National Aeronautics and Space Administration (NASA)
Author: National Aeronautics and Space Administration (NASA)
Author: National Aeronautics and Space Administration (NASA)