Remote Field Eddy Current Probes for the Detection of Stress Corrosion in Transmission Pipelines PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Remote Field Eddy Current Probes for the Detection of Stress Corrosion in Transmission Pipelines PDF full book. Access full book title Remote Field Eddy Current Probes for the Detection of Stress Corrosion in Transmission Pipelines by . Download full books in PDF and EPUB format.
Author: Publisher: ISBN: Category : Languages : en Pages :
Book Description
Magnetic flux leakage (MFL) is a technique used widely in non-destructive testing (NDT) of natural gas and petroleum transmission pipelines. This inspection method relies on magnetizing the pipe-wall in axial direction. The MFL inspection tool is equipped with an array of Hall sensors located around the circumference of the pipe, which registers the flux leakage caused by any defects present in the pipe-wall. Currently, the tool magnetizes the pipewall in axial direction making it largely insensitive to axially oriented defects. One type of defect, which is of a growing concern in the gas and petroleum industry is the stress corrosion crack (SCC). The SCCs are a result of aging, corrosion, fatigue and thermal stresses. SCCs are predominantly axially oriented and are extremely tight, which makes them impossible to be detected using current inspection technology. A possible solution to this problem is to utilize the remote field eddy current (RFEC) effect to detect axially oriented defects. The RFEC method has been widely used in industry in the inspection of tubular products. The method uses a pair of excitation and pick-up coils. The pick-up coil located in the remote field region, usually two, three pipe-diameters away from the excitation coil. With RFEC the presence of defects is detected by the disturbance in the phase of the signal measured by the pick-up coil relative to that of the excitation coil. Unlike conventional eddy current testing the RFEC method is sensitive to defects on the exterior of the inspected product, which makes it a good candidate for the development of in-line inspection technology. This work focuses on the development of non-destructive testing technique, which uses remote field eddy currents induced by rotating magnetic field (RMF). A major advantage of the RMF is that it makes possible to not only detect a defect but also localize its position in circumferential direction. Also, it could potentially allow detection of defects, regardless of their shape and orientation. In this work the RFEC-RMF technique is investigated and is shown to be a useful tool in the detection of axially oriented, circumferentially oriented and skewed notches, SCCs and round defects. Finally, a data acquisition system is designed, capable of performing the RFEC-RMF measurements automatically.
Author: Publisher: ISBN: Category : Languages : en Pages :
Book Description
Magnetic flux leakage (MFL) is a technique used widely in non-destructive testing (NDT) of natural gas and petroleum transmission pipelines. This inspection method relies on magnetizing the pipe-wall in axial direction. The MFL inspection tool is equipped with an array of Hall sensors located around the circumference of the pipe, which registers the flux leakage caused by any defects present in the pipe-wall. Currently, the tool magnetizes the pipewall in axial direction making it largely insensitive to axially oriented defects. One type of defect, which is of a growing concern in the gas and petroleum industry is the stress corrosion crack (SCC). The SCCs are a result of aging, corrosion, fatigue and thermal stresses. SCCs are predominantly axially oriented and are extremely tight, which makes them impossible to be detected using current inspection technology. A possible solution to this problem is to utilize the remote field eddy current (RFEC) effect to detect axially oriented defects. The RFEC method has been widely used in industry in the inspection of tubular products. The method uses a pair of excitation and pick-up coils. The pick-up coil located in the remote field region, usually two, three pipe-diameters away from the excitation coil. With RFEC the presence of defects is detected by the disturbance in the phase of the signal measured by the pick-up coil relative to that of the excitation coil. Unlike conventional eddy current testing the RFEC method is sensitive to defects on the exterior of the inspected product, which makes it a good candidate for the development of in-line inspection technology. This work focuses on the development of non-destructive testing technique, which uses remote field eddy currents induced by rotating magnetic field (RMF). A major advantage of the RMF is that it makes possible to not only detect a defect but also localize its position in circumferential direction. Also, it could potentially allow detection of defects, regardless of their shape and orientation. In this work the RFEC-RMF technique is investigated and is shown to be a useful tool in the detection of axially oriented, circumferentially oriented and skewed notches, SCCs and round defects. Finally, a data acquisition system is designed, capable of performing the RFEC-RMF measurements automatically.
Author: Plamen Alexandrov Ivanov Publisher: ISBN: Category : Languages : en Pages : 164
Book Description
Magnetic flux leakage (MFL) is a technique used widely in non-destructive testing (NDT) of natural gas and petroleum transmission pipelines. This inspection method relies on magnetizing the pipe-wall in axial direction. The MFL inspection tool is equipped with an array of Hall sensors located around the circumference of the pipe, which registers the flux leakage caused by any defects present in the pipe-wall. In general, the tool is constructed such that the magnetization occurs in axial direction as a result of which this method is not sensitive to axially oriented defects. One type of defect, which is of a growing concern for the gas and petroleum industry is the stress corrosion crack (SCC). The SCCs are a result of aging, corrosion, fatigue and thermal stresses. SCCs are predominantly axially oriented and are extremely tight, which makes them impossible to detect using the current inspection technology. One possible solution to this problem is to utilize the remote field eddy current (RFEC) effect to detect axially oriented defects. The RFEC method has been widely used in the industry in the inspection of tubular products. The method uses a pair of excitation and pick-up coils. The pick-up coil is located in the remote field region, usually two, three pipe-diameters away from the excitation coil. With RFEC the presence of defects is detected by the disturbance in the phase of the signal measured by the pick-up coil. Unlike conventional eddy current testing the RFEC method is sensitive to defects on the exterior of the inspected product, which makes it a good candidate for the development of in-line inspection technology. This work focuses on the development of non-destructive testing technique, which uses remote field eddy currents induced by rotating magnetic field (RMF). A major advantage of the RMF is that it makes possible to not only detect a defect but also localize its position in circumferential direction. Also, it could potentially allow detection of defects, regardless of their shape and orientation. In this work the RFEC-RMF technique is investigated and is shown to be useful tool in the detection of axially oriented, circumferentially oriented and skewed notches, SCCs and round defects. A data acquisition system capable of performing the RFEC-RMF measurements automatically was designed.
Author: Donald O. Thompson Publisher: Springer Science & Business Media ISBN: 146151987X Category : Technology & Engineering Languages : en Pages : 2462
Book Description
These Proceedings, consisting of Parts A and B, contain the edited versions of most of the papers presented at the annual Review of Progress in Quantitative Nondestructive Evaluation held at Snowmass Village, Colorado, on July 31 to August 4, 1994. The Review was organized by the Center for NDE at Iowa State University, in cooperation with the Ames Laboratory of the US DOE, the Materials Directorate of the Wright Laboratory, Wright-Patterson Air Force Base, the American Society of Nondestructive Testing, the Department of Energy, the National Institute of Standards and Technology, the Federal Aviation Administration, the National Science Foundation Industry/University Cooperative Research Centers, and the Working Group in Quantitative NDE. This year's Review of Progress in QNDE was attended by approximately 450 participants from the U.S. and many foreign countries who presented over 360 papers. The meeting was divided into 36 sessions, with as many as four sessions running concurrently. The Review covered all phases of NDE research and development from fundamental investigations to engineering applications or inspection systems, and it included many important methods of inspection science from acoustics to x-rays. In the last eight to ten years, the Review has stabilized at about its current size, which most participants seem to agree is large enough to permit a full-scale overview of the latest developments, but still small enough to retain the collegial atmosphere which has marked the Review since its inception.
Author: Publisher: ISBN: Category : Languages : en Pages :
Book Description
The U.S. Department of Energy, National Energy Technology Laboratory funded a Natural Gas Infrastructure Reliability program directed at increasing and enhancing research and development activities in topics such as remote leak detection, pipe inspection, and repair technologies and materials. The Albany Research Center (ARC), U.S. Department of Energy was funded to study the use of electrochemical noise sensors for detection of localized and general corrosion of natural gas transmission pipelines. As part of this, ARC entered into a collaborative effort with the corrosion sensor industry to demonstrate the capabilities of commercially available remote corrosion sensors for use with the Nation's Gas Transmission Pipeline Infrastructure needs. The goal of the research was to develop an emerging corrosion sensor technology into a monitor for the type and degree of corrosion occurring at key locations in gas transmission pipelines.
Author: 
Author: 
Author: Plamen Alexandrov Ivanov
Author: Dr. Bruce J. Nestleroth
Author: Dr. Bruce J. Nestleroth
Author: 
Author: 
Author: Donald O. Thompson
Author: 
Author: 
Author: