Author: Nicholas John Hoff
Publisher:
ISBN:
Category : Monocoque construction
Languages : en
Pages : 696
Book Description
Formulas for the calculation of influence coefficients of curved beams of constant radius of curvature are presented corresponding to displacements in the plane of curvature. Moreover, numerical values are given in tabular and graphicform for a limited number of values of the parameters involved.
Numerical Procedures for the Calculation of Stresses in Monocoques
Author: Nicholas John Hoff
Publisher:
ISBN:
Category : Monocoque construction
Languages : en
Pages : 696
Book Description
Formulas for the calculation of influence coefficients of curved beams of constant radius of curvature are presented corresponding to displacements in the plane of curvature. Moreover, numerical values are given in tabular and graphicform for a limited number of values of the parameters involved.
Publisher:
ISBN:
Category : Monocoque construction
Languages : en
Pages : 696
Book Description
Formulas for the calculation of influence coefficients of curved beams of constant radius of curvature are presented corresponding to displacements in the plane of curvature. Moreover, numerical values are given in tabular and graphicform for a limited number of values of the parameters involved.
Numerical Procedures for the Calculation of the Stresses in Monocoques
Author: N. J. Hoff
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 80
Book Description
Experiments were carried out at the Polytechnic Institute of Brooklyn with both curved and flat reinforced sheet models the longitudinals of which were loaded axially. The stress distribution in longitudinals and sheet was measured with electric strain gages. The stresses then were calculated with the aid of a procedure of successive approximations based upon simplifying assumptions concerning the state of stress in a simple reinforced panel. The agreement between calculations and experiment was found to be reasonably good.
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 80
Book Description
Experiments were carried out at the Polytechnic Institute of Brooklyn with both curved and flat reinforced sheet models the longitudinals of which were loaded axially. The stress distribution in longitudinals and sheet was measured with electric strain gages. The stresses then were calculated with the aid of a procedure of successive approximations based upon simplifying assumptions concerning the state of stress in a simple reinforced panel. The agreement between calculations and experiment was found to be reasonably good.
Numerical Procedures for the Calculation of the Stresses in Monocoques. 3 - Calculation of the Bending Moments in Fuselage Frames
Numerical Procedures for the Calculation of the Stresses in Monocoques
Author: Nicholas John Hoff
Publisher:
ISBN:
Category : Bending moment
Languages : en
Pages : 105
Book Description
This report deals with the calculation of the bending moments and the distortions of fuselage rings upon which known concentrated and distributed loads are acting. In the procedure suggested, the ring is divided into a number of beams each having a constant radius of curvature. The forces and moments caused in the end sections of the beams by individual unit displacements of the end sections are listed in a table designated as the operations table in conformity with Southwell's nomenclature.
Publisher:
ISBN:
Category : Bending moment
Languages : en
Pages : 105
Book Description
This report deals with the calculation of the bending moments and the distortions of fuselage rings upon which known concentrated and distributed loads are acting. In the procedure suggested, the ring is divided into a number of beams each having a constant radius of curvature. The forces and moments caused in the end sections of the beams by individual unit displacements of the end sections are listed in a table designated as the operations table in conformity with Southwell's nomenclature.
Technical Note - National Advisory Committee for Aeronautics
Author: United States. National Advisory Committee for Aeronautics
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 958
Book Description
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 958
Book Description
Report
Author: United States. National Advisory Committee for Aeronautics
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 34
Book Description
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 34
Book Description
Investigation of Bonding Between Metals and Ceramics
Author: H. J. Hamjian
Publisher:
ISBN:
Category : Boron compounds
Languages : en
Pages : 696
Book Description
The experiments conducted with boron carbide and each of four metals showed that nickel, cobalt, and iron formed a bonding zone between the metal and the ceramic and that chromium showed satisfactory physical wetting characteristics on the ceramic.
Publisher:
ISBN:
Category : Boron compounds
Languages : en
Pages : 696
Book Description
The experiments conducted with boron carbide and each of four metals showed that nickel, cobalt, and iron formed a bonding zone between the metal and the ceramic and that chromium showed satisfactory physical wetting characteristics on the ceramic.
United States Government Publications Monthly Catalog
Author:
Publisher:
ISBN:
Category : Government publications
Languages : en
Pages : 1718
Book Description
Publisher:
ISBN:
Category : Government publications
Languages : en
Pages : 1718
Book Description
Index of NACA Technical Publications
Author: United States. National Advisory Committee for Aeronautics
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 1370
Book Description
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 1370
Book Description