Author: Arnold Engineering Development CenterPublisher:
ISBN:
Category : Magnetohydrodynamic generators
Languages : en
Pages :
Book Description
MHD High Performance Demonstration Experiment
Author: Arnold Engineering Development CenterPublisher:
ISBN:
Category : Magnetohydrodynamic generators
Languages : en
Pages :
Book Description
MHD high performance demonstration experiment
Author: Arnold Engineering Development CenterPublisher:
ISBN:
Category : Magnetohydrodynamic generators
Languages : en
Pages : 24
Book Description
The assembly of the magnet continued, the generator channel assembly was completed, and burner testing was resumed. Channel assembly operations were completed approximately two weeks ahead of schedule, even though the operation was approximately four weeks behind schedule at the start of the quarter. At the close of the quarter, seven of the nine upper coil pancakes had been installed and the eighth pancake was in position for final placement on the magnet. Burner testing was resumed; however, only one firing with the traversing pressure probe and electrode test assembly installed was performed.
MHD High Performance Demonstration Experiment
Author: Annual Report on the MHD High Performance Demonstration Experiment for the Period November 15, 1973 - April 30, 1975
Author: Arnold Engineering Development CenterPublisher:
ISBN:
Category : Magnetohydrodynamic generators
Languages : en
Pages : 176
Book Description
Analytical Investigation of Critical Phenomena in MHD Power Generators
Author: Publisher:
ISBN:
Category : Electric power production
Languages : en
Pages : 380
Book Description
MHD High Performance Demonstration Experiment. Quarterly Progress Report, April 1, 1979-June 30, 1979
Author: Publisher:
ISBN:
Category :
Languages : en
Pages :
Book Description
The objective of this experimental research, started late in 1973, is to demonstrate the attainment of MHD performance ona sufficiently large scale to verify that the projected efficiency of the commercial MHD concept is attainable. To perform the experiment, an existing facility at the Arnold Engineering Development Center (USAF) was refurbished and the new systems required for performing the experiment have been designed and built. In particular, the largest systems which have required the greatest expenditure of resources are the generator channel and the 6 Tesla (T) cryogenically cooled magnet. Both of these systems are now complete and the magnet has been tested at low field strengths. During the period between April 1, 1979, and June 30, 1979, the assembly operations on the magnet and its cryogenic cooling system were completed. The pressure testing of the generator channel was completed and the channel was installed in the magnet to facilitate final alignment of the burner. The diffuser assembly operations were completed. The magnet was retested in the warm mode, repeating the tests performed in December 1978 during wich an arc-over occurred. No problems were encountered in the latest tests and the magnet was subsequently cooled to 165°K and pulsed to a peak field strength of 2.9 T. Analytic studies of the operation of the generator with supersonic flow at low magnetic fields were started and are continuing.
MHD Performance Demonstration Experiment, October 1, 1080-September 30, 1981
Author: Publisher:
ISBN:
Category :
Languages : en
Pages :
Book Description
The Arnold Engineering Development Center (AEDC) has been under contract with the Department of Energy (DOE) since December 1973 to conduct a magnetohydrodynamic (MHD) High Performance Demonstration Experiment (HPDE). The objective of this experimental research is to demonstrate the attainment of MHD performance on a sufficiently large scale to verify that projected commercial MHD objectives are possible. This report describes the testing of the system under power-producing conditions during the period from October 1, 1980 to September 30, 1981. Experimental results have been obtained with the channel configured in the Faraday mode. Test conditions were selected to produce low supersonic velocity along the entire channel length. Tests have been conducted at magnetic fields up to 4.1 Tesla (T) (70% of design). Up to 30.5 MW of power has been produced to date (60% of design) for an enthalpy extraction of approximately 11%. The high Hall voltage transient, observed during the previous series of tests has been reduced. The reduction is mostly probably due to the fuel and seed being introduced simultaneously. The replacement of the ATJ graphite caps on the electrode walls with pyrolytic graphite caps has resulted in significantly higher surface temperature. As a result, the voltage drop is some 60% of the cold wall voltage drop during the previous series of tests. However, the absolute value of the present voltage drop is still greater than the original design predictions. Test results indicate, however, that the overall enthalpy extraction objective can be achieved.
Development of Design Criteria, Cost Estimates, and Schedules for an MHD High Performance Demonstration Experiment
Author: Arnold Engineering Development CenterPublisher:
ISBN:
Category : Magnetohydrodynamic generators
Languages : en
Pages : 124
Book Description
MHD High Performance Demonstration Experiment. Interagency Agreement No. ET-78-I-01-2895. Quarterly Progress Report, October 1-December 31, 1978
Author: Publisher:
ISBN:
Category :
Languages : en
Pages :
Book Description
The objective of this experimental research, initiated in December 1973, is to demonstrate the attainment of MHD performance on a sufficiently large scale to verify that the projected efficiency of the commercial MHD concept is viable. To perform the experiment, an existing facility at the Arnold Engineering Development Center was refurbished and the new systems required for performing the experiment have been designed and built. In particular, the largest systems which have required the greatest portion of the expended effort are the generator channel and 6 Tesla (T) cryogenically cooled magnet. The generator channel is now complete and the magnet is approximately 85 percent complete. Proof testing of various components has been performed to the extent possible and extensive testing of the plasma generator with its ancillary systems in particular has been completed. During the period between October 1, 1978 and December 31, 1978, the assembly of the magnet continued with the installation of the force containment structure (FCS) and upper pole steel being completed. Final placement of the magnet was accomplished and initial testing of the magnet performance was started. In the course of this testing, an arc over occurred in the outlet end coolant tubes and the testing was terminated to effect remedial repairs. Prior to the arc over, three successful powered tests with a peak field strength slightly greater than 2 T were performed. Fabrication of the components for the subsonic diffuser and alignment of the generator channel sections on the channel cart were also completed in this period.
Author: