Author: Fasteners Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications. Current requirements for Mechanical and Quality Requirements for Metric Externally Threaded Steel Fasteners are contained in ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel - Bolts, screws, and studs. SAE J1199 contains useful information and may have current users. However, several of the references have been cancelled or superseded.
Mechanical and Material Requirements for Metric Externally Threaded Steel Fasteners
Author: Fasteners Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications. Current requirements for Mechanical and Quality Requirements for Metric Externally Threaded Steel Fasteners are contained in ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel - Bolts, screws, and studs. SAE J1199 contains useful information and may have current users. However, several of the references have been cancelled or superseded.
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications. Current requirements for Mechanical and Quality Requirements for Metric Externally Threaded Steel Fasteners are contained in ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel - Bolts, screws, and studs. SAE J1199 contains useful information and may have current users. However, several of the references have been cancelled or superseded.
Mechanical and Material Requirements for Metric Series Externally Threaded Steel Fasteners
Author: Industrial Fasteners Institute
Publisher:
ISBN:
Category : Fasteners
Languages : en
Pages : 24
Book Description
Publisher:
ISBN:
Category : Fasteners
Languages : en
Pages : 24
Book Description
Mechanical and Material Requirements for Metric Externally Threaded Steel Fasteners
Author: American National Standards Institute
Publisher:
ISBN:
Category : Fasteners
Languages : en
Pages : 5
Book Description
Publisher:
ISBN:
Category : Fasteners
Languages : en
Pages : 5
Book Description
Mechanical and Material Requirements for Externally Threaded Fasteners
Author: Fasteners Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 in sizes to 1-1/2 in. inclusive.The term "stud" as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing. Other properties such as fatigue behavior, corrosion resistance, impact properties, etc., are beyond the scope of this document and responsibility for ensuring the acceptability of the product for applications where conditions warrant consideration of these other properties shall be borne by the end user. Allow higher S and P percentages in alloy steel than allowed in Table 2 for manufacturing Grade 8 screws and bolts by hot forging or machining from bar. As an example, this enables producers of Grade 8 bolts and screws to use SAE 4140 steel that might not otherwise be acceptable for hot forging and machining from bar. The S and P values in Table 2 must be adhered to for all cold formed fasteners.
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 in sizes to 1-1/2 in. inclusive.The term "stud" as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing. Other properties such as fatigue behavior, corrosion resistance, impact properties, etc., are beyond the scope of this document and responsibility for ensuring the acceptability of the product for applications where conditions warrant consideration of these other properties shall be borne by the end user. Allow higher S and P percentages in alloy steel than allowed in Table 2 for manufacturing Grade 8 screws and bolts by hot forging or machining from bar. As an example, this enables producers of Grade 8 bolts and screws to use SAE 4140 steel that might not otherwise be acceptable for hot forging and machining from bar. The S and P values in Table 2 must be adhered to for all cold formed fasteners.
What Every Engineer Should Know about Threaded Fasteners
Author: Alexander Blake
Publisher: CRC Press
ISBN: 9780849383793
Category : Technology & Engineering
Languages : en
Pages : 224
Book Description
Publisher: CRC Press
ISBN: 9780849383793
Category : Technology & Engineering
Languages : en
Pages : 224
Book Description
Mechanical and Material Requirements for Externally Threaded Fasteners
Mechanical and Material Requirements for Externally Threaded Fasteners
Author: Society of Automotive Engineers
Publisher:
ISBN:
Category : Fasteners
Languages : en
Pages : 15
Book Description
Publisher:
ISBN:
Category : Fasteners
Languages : en
Pages : 15
Book Description
Mechanical and Material Requirements for Metric Threaded Fasteners
Author: JB. Belford
Publisher:
ISBN:
Category : Fasteners
Languages : en
Pages : 9
Book Description
The primary objective of the ANSI/OMFS Subcommittee on Material and Performance was to develop ways to maximize the efficient use of raw material in its conversion into metric fastener products, using simplicity and product performance concepts. The results have been the standardization of mechanical, metallurgical, and plating requirements for internally and externally threaded fasteners made from ferrous and nonferrous materials. During this study, considerable investigation of the actual and potential relationships of material to performance of the end product was conducted.
Publisher:
ISBN:
Category : Fasteners
Languages : en
Pages : 9
Book Description
The primary objective of the ANSI/OMFS Subcommittee on Material and Performance was to develop ways to maximize the efficient use of raw material in its conversion into metric fastener products, using simplicity and product performance concepts. The results have been the standardization of mechanical, metallurgical, and plating requirements for internally and externally threaded fasteners made from ferrous and nonferrous materials. During this study, considerable investigation of the actual and potential relationships of material to performance of the end product was conducted.
Mechanical and Material Requirements for Externally Threaded Fasteners
Author: Society of Automotive Engineers
Publisher:
ISBN:
Category : Fasteners
Languages : en
Pages : 6
Book Description
Publisher:
ISBN:
Category : Fasteners
Languages : en
Pages : 6
Book Description
Surface vehicle standard
Author: Society of Automotive Engineers
Publisher:
ISBN:
Category :
Languages : es
Pages : 14
Book Description
Publisher:
ISBN:
Category :
Languages : es
Pages : 14
Book Description