Author: Sadik Kakaç
Publisher: Wiley-Interscience
ISBN:
Category : Science
Languages : en
Pages : 1268

View

Book Description
Very Good,No Highlights or Markup,all pages are intact.

Author: R. K. Shah
Publisher: Academic Press
ISBN: 1483191303
Category : Technology & Engineering
Languages : en
Pages : 492

View

Book Description
Laminar Flow Forced Convection in Ducts is a sourcebook for compact heat exchanger analytical data. This book describes the analytical solutions for laminar fluid flow and forced convection heat transfer in circular and noncircular pipes, including applicable differential equations and boundary conditions involving velocity and temperature problems of fluid flow. The book also discusses fluid flow—how much power is required to pump fluids through the heat exchanger, as well as the heat transfer—the determination of q" distribution, and the temperature of fluid and walls. The text also analyzes the coolant or heat transfer fluid flows in a nuclear power reactor composed of a bundle of circular section fuel rods located inside a round tube. R.A. Axford addresses fluid flow and heat transfers results for the rod bundle geometry in "Heat Transfer in Rod Bundles." The book also provides an overview and guidelines that can be used for the designer and the applied mathematician. This book is suitable for engineers working in electronics, aerospace, instrumentation, and biomechanics that use cooling or heating exchanges or solar collection systems.

Author: Geoffrey Hewitt
Publisher: Elsevier
ISBN: 1483285235
Category : Technology & Engineering
Languages : en
Pages : 327

View

Book Description
Annular Two-Phase Flow presents the wide range of industrial applications of annular two-phase flow regimes. This book discusses the fluid dynamics and heat transfer aspects of the flow pattern. Organized into 12 chapters, this book begins with an overview of the classification of the various types of interface distribution observed in practice. This text then examines the various regimes of two-phase flow with emphasis on the regions of occurrence of the annular flow regime. Other chapters consider the single momentum and energy balances, which illustrate the differences and analogies between single- and two-phase flows. This book discusses as well the simple modes for annular flow with consideration to the calculation of the profile of shear stress in the liquid film. The final chapter deals with the techniques that are developed for the measurement of flow pattern, entrainment, and film thickness. This book is a valuable resource for chemical engineers.

Author: Salim Newaz Kazi
Publisher: IntechOpen
ISBN: 9789535108276
Category : Technology & Engineering
Languages : en
Pages : 540

View

Book Description
In the wake of energy crisis due to rapid growth of industries, urbanization, transportation, and human habit, the efficient transfer of heat could play a vital role in energy saving. Industries, household requirements, offices, transportation are all dependent on heat exchanging equipment. Considering these, the present book has incorporated different sections related to general aspects of heat transfer phenomena, convective heat transfer mode, boiling and condensation, heat transfer to two phase flow and heat transfer augmentation by different means.

Author: G. Hetsroni
Publisher: Elsevier
ISBN: 1483160505
Category : Science
Languages : en
Pages : 779

View

Book Description
Proceedings of the International Symposium on Two-Phase Systems

Author: United States. National Bureau of Standards
Publisher:
ISBN:
Category : Hydraulic engineering
Languages : en
Pages : 260

View

Book Description

Author: Afshin J. Ghajar
Publisher: Springer
ISBN: 9783030416256
Category : Science
Languages : en
Pages : 0

View

Book Description
This book provides design engineers using gas-liquid two-phase flow in different industrial applications the necessary fundamental understanding of the two-phase flow variables. Two-phase flow literature reports a plethora of correlations for determination of flow patterns, void fraction, two- phase pressure drop and non-boiling heat transfer correlations. However, the validity of a majority of these correlations is restricted over a narrow range of two -phase flow conditions. Consequently, it is quite a challenging task for the end user to select an appropriate correlation/model for the type of two-phase flow under consideration. Selection of a correct correlation also requires some fundamental understanding of the two-phase flow physics and the underlying principles/assumptions/limitations associated with these correlations. Thus, it is of significant interest for a design engineer to have knowledge of the flow patterns and their transitions and their influence on two-phase flow variables. To address some of these issues and facilitate selection of appropriate two-phase flow models, this volume presents a succinct review of the flow patterns, void fraction, pressure drop and non-boiling heat transfer phenomenon and recommend some of the well scrutinized modeling techniques.

Author: Lixin Cheng
Publisher: Springer Science & Business Media
ISBN: 3319043587
Category : Technology & Engineering
Languages : en
Pages : 215

View

Book Description
This volume presents state-of-the-art of reviews in the field of multiphase flow. In focusses on nonlinear aspects of multiphase flow networks as well as visualization experiments. The first chapter presents nonlinear aspects or deterministic chaos issues in the systems of multi-phase reactors. The second chapter reviews two-phase flow dynamics in combination with complex network theory. The third chapter discusses evaporation mechanism in the wick of copper heat pipes. The last chapter investigates numerically the flow dynamics and heat and mass transfer in the laminar and turbulent boundary layer on the flat vertical plate.

Author: Afshin J. Ghajar
Publisher: Springer Nature
ISBN: 3030872815
Category : Science
Languages : en
Pages : 280

View

Book Description
The book provides design engineers an elemental understanding of the variables that influence pressure drop and heat transfer in plain and micro-fin tubes to thermal systems using liquid single-phase flow in different industrial applications. It also provides design engineers using gas-liquid, two-phase flow in different industrial applications the necessary fundamentals of the two-phase flow variables. The author and his colleagues were the first to determine experimentally the very important relationship between inlet geometry and transition. On the basis of their results, they developed practical and easy to use correlations for the isothermal and non-isothermal friction factor (pressure drop) and heat transfer coefficient (Nusselt number) in the transition region as well as the laminar and turbulent flow regions for different inlet configurations and fin geometry. This work presented herein provides the thermal systems design engineer the necessary design tools. The author further presents a succinct review of the flow patterns, void fraction, pressure drop and non-boiling heat transfer phenomenon and recommends some of the well scrutinized modeling techniques.

Author:
Publisher:
ISBN:
Category : Weights and measures
Languages : en
Pages : 844

View

Book Description