Laboratory Evaluation of Crumb Rubber Asphalt Concrete Mixtures Using the Concepts of SMA Mixtures PDF Download

Author: Somasekhar Reddy Rebala
Publisher:
ISBN:
Category :
Languages : en
Pages : 430

View

Book Description

Author: Wade H. Shafer
Publisher: Springer Science & Business Media
ISBN: 1461303931
Category : Science
Languages : en
Pages : 427

View

Book Description
Masters Theses in the Pure and Applied Sciences was first conceived, published, and disseminated by the Center for Information and Numerical Data Analysis and Synthesis (CINDAS)* at Purdue University in 1957, starting its coverage of theses with the academic year 1955. Beginning with Volume 13, the printing and dis semination phases of the activity were transferred to University Microfilms/Xerox of Ann Arbor, Michigan, with the thought that such an arrangement would be more beneficial to the academic and general scientific and technical community. After five years of this joint undertaking we had concluded that it was in the interest of all concerned if the printing and distribution of the volumes were handled by an international publishing house to assure improved service and broader dissemination. Hence, starting with Volume 18, Masters Theses in the Pure and Applied Sciences has been disseminated on a worldwide basis by Plenum Publishing Corporation of New York, and in the same year the coverage was broadened to include Canadian universities. All back issues can also be ordered from Plenum. We have reported in Volume 39 (thesis year 1994) a total of 13,953 thesis titles from 21 Canadian and 159 United States universities. We are sure that this broader base for these titles reported will greatly enhance the value of this impor tant annual reference work. While Volume 39 reports theses submitted in 1994, on occasion, certain uni versities do report theses submitted in previous years but not reported at the time.

Author: Dimitirios G. Goulias
Publisher:
ISBN:
Category : Asphalt concrete
Languages : en
Pages : 474

View

Book Description

Author:
Publisher:
ISBN:
Category : Asphalt-rubber
Languages : en
Pages : 198

View

Book Description
This research program was based on laboratory and field studies. All work was limited to the use of a 10-mesh crumb rubber in the dry process. An evaluation of the asphalt-rubber interactions indicated that there should be a reasonable level of interaction between the crumb rubber and the asphalt cement selected for the project. A suggested criterion for defining an acceptable level of interaction would be to establish a minimum viscosity of 15 Poise (Brookfield viscosity) for a neat asphalt cement modified with 20% crumb rubber. When designing a crumb rubber modified mixture, the aggregate gradation should be substantially gapped. The target gradation used in the construction of the Babbit, Minnesota test sections should be adjusted for crumb rubber gradations volumetrically; generally, 1 gram of crumb rubber occupies the same volume as 3 grams of aggregate for a given sieve size. The optimum asphalt content for crumb rubber mixtures should be based on air voids from 1.5 to 3%.

Author: Gajanan Suresh Natu
Publisher:
ISBN:
Category : Asphalt concrete
Languages : en
Pages : 338

View

Book Description

Author: Robert W. Saxton
Publisher:
ISBN:
Category : Pavements, Asphalt
Languages : en
Pages : 246

View

Book Description
This study investigated the laboratory performance of crumb rubber modified mixtures compared to a standard bituminous mixture using performance based test procedures. This study was part of an asphalt resurfacing program for the Seattle Washington area. Laboratory analyses were used to estimate the long term pavement performance of these mixtures in the field. Six mixtures were tested: The standard Class 'A' surface mixture for the Seattle area, Plus Ride II® base course gradation (dry process) using AC 5 and AR 4000W binder types, Plus Ride II® surface course gradation (dry process) using AC 5 and AR 4000W binder types, and ARHM-GG surface course gradation using crumb rubber modified (CRM) AR 2000 (wet process). The performance based tests used on each mixture evaluated the different failure modes a pavement may encounter in the field: fatigue cracking, permanent deformation (rutting), thermal cracking, age hardening, and water sensitivity. Many of the tests used were developed by the Strategic Highway Research Program (SHRP) to test for a mixtures susceptibility in these failure modes. Test results indicate the CRM mixtures performed better than the Class 'A' surface mixture, with respect to fatigue cracking. All of the Plus Ride II® mixtures performed inadequately when tested for permanent deformation. On the other hand, the ARHM-GG surface mixture performed well, even better than the Class 'A' surface mixture with respect to permanent deformation. The ARHM-GG surface mixture showed better low temperature characteristics when compared to the Class 'A' surface and Plus Ride II® mixtures. The CRM mixtures were less susceptible to aging than the Class 'A' surface mixture. Finally, all of the mixtures demonstrated low moisture sensitivity. The final conclusions were made relative to the Class 'A' surface mixture. The ARHM-GG surface mixture performed as well as, and in some cases better than, the Class 'A' surface mixture. The ARHM-GG surface mixture may be used where the Class 'A' surface mixture was specified. The Plus Ride II® base and surface (AC 5 and AR 4000W) mixtures did perform better than the Class 'A' surface mixture in some tests, however it performed worse in others. Therefore, it was recommended that the Plus Ride II® mixture designs be re-evaluated to provide adequate performance in the failed tests.

Author: Thomas Bennert
Publisher:
ISBN:
Category : Asphalt-rubber
Languages : en
Pages : 132

View

Book Description

Author: Shanmugam Ramaswami
Publisher:
ISBN:
Category :
Languages : en
Pages : 322

View

Book Description

Author: American Association of State Highway and Transportation Officials
Publisher: AASHTO
ISBN: 1560510552
Category : Pavements
Languages : en
Pages : 622

View

Book Description
Design related project level pavement management - Economic evaluation of alternative pavement design strategies - Reliability / - Pavement design procedures for new construction or reconstruction : Design requirements - Highway pavement structural design - Low-volume road design / - Pavement design procedures for rehabilitation of existing pavements : Rehabilitation concepts - Guides for field data collection - Rehabilitation methods other than overlay - Rehabilitation methods with overlays / - Mechanistic-empirical design procedures.

Author: Chandra K. Akisetty
Publisher:
ISBN:
Category : Crumb rubber
Languages : en
Pages : 8

View

Book Description
Warm mix asphalt (WMA) refers to technologies which allow a significant reduction of mixing and compaction temperatures of asphalt mixes. From previous studies, it is observed that warm mix additives work in different ways, either in reducing the viscosity of the asphalt binder or allowing better workability of the asphalt mix at lower temperatures through volume expansion in the binder. If the technologies of WMA are incorporated into rubberized asphalt mixes, which are generally produced and compacted at higher temperature than conventional mixes, it is possible to reduce the mixing and compaction temperatures of rubberized mixes to those of conventional mixes. This paper presents a limited study that characterizes the engineering properties of crumb rubber modifier (CRM) mixtures containing warm mix additives. Six CRM mixtures (two of control mixtures and four of warm mixtures) were prepared using two aggregate sources and two additives: Aspha-min® and Sasobit®. Evaluation of all mixtures included the following testing procedures: tensile strength ratio, asphalt pavement analyzer, resilient modulus, and resilient modulus after long-term oven aging. The results from this study showed that in general, there was no significant difference between the control and warm CRM mixtures for the properties evaluated in this study, indicating that the use of WMA technologies into CRM mixes is expected to have no negative effect on the mixture's engineering properties.