Laboratory and Field Evaluation of Warm Mix Asphalt Technology to Determine Its Applicability for Massachusetts PDF Download

Author: Walaa S. Mogawer
Publisher:
ISBN:
Category : Pavements
Languages : en
Pages : 89

View

Book Description

Author: Alexander Jordan Austerman
Publisher:
ISBN:
Category :
Languages : en
Pages : 190

View

Book Description

Author: Zhanping Yuo
Publisher:
ISBN:
Category : Asphalt emulsion mixtures
Languages : en
Pages : 0

View

Book Description
Hot Mix Asphalt (HMA) has been traditionally produced at a discharge temperature of between 280° F (138° C) and 320° F (160° C), resulting in high energy (fuel) costs and generation of greenhouse gases. The goal for Warm Mix Asphalt (WMA) is to use existing HMA plants and specifications to produce quality dense graded mixtures at significantly lower temperatures. Europeans are using WMA technologies that allow the mixture to be placed at temperatures as low as 250° F (121° C). It is reported that energy savings on the order of 30%, with a corresponding reduction in CO2 emissions of 30%, are realized when WMA is used compared to conventional HMA. Although numerous studies have been conducted on WMA, only limited laboratory experiments are available and most of the current WMA laboratory test results are inconsistent and not compatible with field performance The main objectives of this study are: The main objectives of this study are: 1) review and synthesize information on the available WMA technologies; 2) measure the complex/dynamic modulus of WMA and the control mixtures (HMA) for comparison purpose and for use in mechanistic-empirical (ME) design comparison; 3) assess the rutting and fatigue potential of WMA mixtures; and 4) provide recommendation for the proper WMA for use in Michigan considering the aggregate, binder, and climatic factors. The testing results indicated that most of the WMA has higher fatigue life and TSR which indicated WMA has better fatigue cracking and moisture damage resistant; however, the rutting potential of most of the WMA tested were higher than the control HMA. In addition, the WMA design framework was developed based on the testing results, and presented in this study to allow contractors and state agencies to successfully design WMA around the state of Michigan.

Author: Faramarz Farshidi
Publisher:
ISBN: 9781267758804
Category :
Languages : en
Pages :

View

Book Description
In recent years Warm Mix Asphalt (WMA) technologies have been used to modify asphalt binders, with the following objectives: to decrease production and construction temperatures, reduce fumes and emissions, increase haul distance, and improve the workability of the mix. Reduced temperatures at the plant and during laydown and compaction are hypothesized to positively impact long-term oxidative aging behavior due to less oxidation/aging and result in less emissions during production and construction due to reduced production and construction temperatures. The purpose of this investigation was to quantify these improvements with respect to long-term oxidative aging in the field and environmental benefits with respect to volatile organic compounds, semi-volatile organic compounds and poly cyclic aromatic hydrocarbons in order to confirm or deny this hypothesis. This research evaluated the potential durability of WMA and Rubberized Warm Mix Asphalt (R-WMA) binders with respect to long-term aging through characterization of field-aged binders extracted and recovered from field cores. The results were compared to the control conventional Hot Mix Asphalt (HMA) and Rubberized Hot Mix Asphalt (R-HMA) samples. Binders were extracted and recovered from thirteen different test sections and a total of seven different WMA technologies were evaluated in this study. The Dynamic Shear Rheometer (DSR) was used to evaluate the rheological properties of the binders at high temperatures with respect to rutting performance in the field. The Bending Beam Rheometer (BBR) was used to characterize low temperature properties of the binder samples. A new testing procedure was developed to measure and characterize the rheological properties of the R-HMA and R-WMA binders with respect to performance-related properties in the field. The rheological results indicated that depending on the WMA technology used, the addition of WMA technologies and reduced production and compaction temperatures result in increase or decrease rutting resistance performance for WMA and R-WMA binders with respect to permanent deformation at high temperatures in the field. Both WMA and R-WMA binders studied meet the established thermal cracking criteria with respect to low temperature cracking in the field. The aging kinetics curves for WMA-treated binders are parallel to the control binders and the addition of WMA technologies including organic, chemical and mechanical foaming technologies studied in this research did not result in a different aging kinetics trend with respect to long-term aging in the field. A portable "flux" chamber was designed and fabricated to capture and directly measure emissions during paving operations. Emissions were collected in activated charcoal sorbent tubes for characterizing volatile organic compounds and semi-volatile organic compounds. XAD-2 resin tubes and filters were used to capture the gaseous phase and particulate phase of the PAH compounds, respectively. A reliable analytical method was developed to identify and quantify alkane emissions using gas chromatography mass spectrometry (GC/MS) in the laboratory. A separate method was developed for identification and characterization of trace level PAH compounds of the asphalt fumes. The results demonstrated that the warm mix asphalt technology type, plant mixing temperature and level of compaction significantly influence the emission characteristics throughout paving operations. Moreover, the emissions kinetics indicated that the majority of the reactive organic gases are volatilized in the first hour after sampling initiation (immediately after production and before compaction). To better understand and identify any chemical composition changes of the binder due to WMA technologies, nuclear magnetic resonance spectroscopy (NMR) was used for understanding structural complexities of HMA and WMA binder molecules. Qualitative analysis of both carbon and hydrogen atoms with HMA and WMA binders showed that the molecular structures of the binders are not significantly changed by the effect of WMA technologies.

Author: Zhanping Yuo
Publisher:
ISBN:
Category : Asphalt emulsion mixtures
Languages : en
Pages : 108

View

Book Description
Hot Mix Asphalt (HMA) has been traditionally produced at a discharge temperature of between 280° F (138° C) and 320° F (160° C), resulting in high energy (fuel) costs and generation of greenhouse gases. The goal for Warm Mix Asphalt (WMA) is to use existing HMA plants and specifications to produce quality dense graded mixtures at significantly lower temperatures. Europeans are using WMA technologies that allow the mixture to be placed at temperatures as low as 250° F (121° C). It is reported that energy savings on the order of 30%, with a corresponding reduction in CO2 emissions of 30%, are realized when WMA is used compared to conventional HMA. Although numerous studies have been conducted on WMA, only limited laboratory experiments are available and most of the current WMA laboratory test results are inconsistent and not compatible with field performance The main objectives of this study are: The main objectives of this study are: 1) review and synthesize information on the available WMA technologies; 2) measure the complex/dynamic modulus of WMA and the control mixtures (HMA) for comparison purpose and for use in mechanistic-empirical (ME) design comparison; 3) assess the rutting and fatigue potential of WMA mixtures; and 4) provide recommendation for the proper WMA for use in Michigan considering the aggregate, binder, and climatic factors. The testing results indicated that most of the WMA has higher fatigue life and TSR which indicated WMA has better fatigue cracking and moisture damage resistant; however, the rutting potential of most of the WMA tested were higher than the control HMA. In addition, the WMA design framework was developed based on the testing results, and presented in this study to allow contractors and state agencies to successfully design WMA around the state of Michigan.

Author: Haritha Malladi
Publisher:
ISBN:
Category :
Languages : en
Pages : 100

View

Book Description

Author: Nathan Bower
Publisher:
ISBN:
Category : Asphalt concrete
Languages : en
Pages : 111

View

Book Description

Author: Jianhua Yu
Publisher:
ISBN:
Category : Asphalt concrete
Languages : en
Pages : 8

View

Book Description
Warm mix asphalt (WMA) technology provides sufficient workability for asphalt mixtures at reduced mixing and compaction temperatures. Depending on the WMA technology, the typical temperature reduction range is 20 °C to 55 °C below hot mix asphalt (HMA) production temperatures. WMA involves chemical and wax additives that are added to an asphalt binder or incorporated through the use of foaming technology. The main advantages of WMA are reduced emissions and a reduction in combustible fuel consumption. Ongoing WMA research projects have documented some differences between HMA and WMA mixes, prompting numerous research projects that are investigating these concerns. The purpose of this research is to evaluate the volumetric properties by directly comparing laboratory produced WMA and HMA mixes. This study investigates the impact of WMA additives on the volumetric properties, specifically, the theoretical maximum specific gravity (Gmm). The Gmm testing followed the procedure of ASTM D2041. Two mix designs with HMA binder were produced, one without recycled asphalt pavement (RAP) and the other with 30 % RAP. After the mix designs were completed, no additional changes were made to account for the addition of the WMA technology. The mixes included the WMA technologies Sasobit and Advera, as well as an HMA control, for a total of six different laboratory produced mixes. Each mix was produced at 120 °C, 135 °C, and 150 °C, and each mix was oven cured for 1, 2, and 4 h. The test results were analyzed using statistical principles to determine whether differences in the Gmm values were statistically significant. The results show that temperature has little impact on Gmm. Gmm was not affected by curing times of 1 and 2 h, but the longer curing time of 4 h resulted in a statistically significant increase in Gmm. Further analysis revealed that the mix sensitivity to curing time depends on the amount of RAP in the mix. For the mix designs studied, the Advera Gmm values were similar to the HMA values, but the Sasobit Gmm values were statistically lower than the Advera values.

Author: Clinton Isaac Van Winkle
Publisher:
ISBN:
Category : Pavements, Asphalt
Languages : en
Pages : 39

View

Book Description
Currently in Iowa, the amount of RAP materials allowed for the surface layer is limited to 15% by weight. The objective of this project was to develop quality standards for inclusion of RAP content higher than 15% in asphalt mixtures. To meet Superpave mix design requirements, it was necessary to fractionate the RAP materials. Based on the extensive sieve-by-sieve analysis of RAP materials, the optimum sieve size to fractionate RAP materials was identified. To determine if the higher percentage of RAP materials than 15% can be used in Iowa's state highway, three test sections with 30.0%, 35.5% and 39.2% of RAP materials were constructed on Highway 6 in Iowa City. The construction of the field test sections was monitored and the cores were obtained to measure field densities of test sections. Field mixtures collected from test sections were compacted in the laboratory in order to test the moisture sensitivity using a Hamburg Wheel Tracking Device. The binder was extracted from the field mixtures with varying amounts of RAP materials and tested to determine the effects of RAP materials on the PG grade of a virgin binder. Field cores were taken from the various mix designs to determine the percent density of each test section. A condition survey of the test sections was then performed to evaluate the short-term performance.

Author: Fan Yin
Publisher:
ISBN:
Category :
Languages : en
Pages : 74

View

Book Description
Warm-Mix Asphalt (WMA) refers to the asphalt concrete paving material produced and placed at temperatures approximately 50°F lower than those used for Hot-Mix Asphalt (HMA). Economic, environmental and engineering benefits have boosted the use of WMA technology across the world during the past decade. While WMA technology has been successfully utilized as a paving material, several specifications and mix design protocols remain under development. For example, currently, there is no consistent laboratory conditioning procedure for preparing WMA specimens for performance tests, despite being essential for mix performance. Based on previous studies, several candidate conditioning protocols for WMA Laboratory Mixed Laboratory Compacted (LMLC) and off-site Plant Mixed Laboratory Compacted (PMLC) specimens were selected, and their effects on mixture properties were evaluated. Mixture stiffness evaluated in a dry condition using the Resilient Modulus (MR) test (ASTM D-7369) was the main parameter used to select a conditioning protocol to simulate pavement stiffness in its early life. The number of Superpave Gyratory Compactor (SGC) gyrations to get 7±0.5% air voids (AV) was the alternative parameter. Extracted binder stiffness and aggregate orientation of field cores and on-site PMLC specimens were evaluated using the Dynamic Shear Rheometer (DSR) (AASHTO T315) and image analysis techniques, respectively. In addition, mixture stiffness in a wet condition was evaluated using the Hamburg Wheel-Track Test (HWTT) (AASHTO T324) stripping inflection point (SIP) and rutting depth at a certain number of passes. Several conclusions are made based on test results. LMLC specimens conditioned for 2 hours at 240°F (116°C) for WMA and 275°F (135°C) for HMA had similar stiffnesses as cores collected during the early life of field pavements. For off-site PMLC specimens, different conditioning protocols are recommended to simulate stiffnesses of on-site PMLC specimens: reheat to 240°F (116°C) for WMA with additives and reheat to 275°F (135°C) for HMA and foamed WMA. Additionally, binder stiffness, aggregate orientation, and overall AV had significant effects on mixture stiffness. Mixture stiffness results for PMFC cores and on-site PMLC specimens in a wet condition as indicated by HWTT agree with those in a dry condition in MR testing. The electronic version of this dissertation is accessible from http://hdl.handle.net/1969.1/148143