High Pressure Soot Formation in Non-smoking Methane-air Laminar Diffusion Flames from 1.5 MPa to 6.0 MPa PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download High Pressure Soot Formation in Non-smoking Methane-air Laminar Diffusion Flames from 1.5 MPa to 6.0 MPa PDF full book. Access full book title High Pressure Soot Formation in Non-smoking Methane-air Laminar Diffusion Flames from 1.5 MPa to 6.0 MPa by Marie Emma Vaillancourt. Download full books in PDF and EPUB format.
Author: Marie Emma Vaillancourt Publisher: ISBN: 9780494210178 Category : Combustion Languages : en Pages : 190
Book Description
Measurements of soot concentration, flame temperature and flame geometry have been recorded for non-smoking methane-air laminar diffusion flames at pressures from P = 1.5 MPa to P = 6.0 MPa. Soot concentration and temperature profiles were obtained using the spectral soot emission diagnostic method and the Abel inversion deconvolution technique. Visual inspection and measurement of the flame revealed a slight increase in height and decrease in cross-section with increasing pressure. Soot volume fraction increased with pressure according to fv max & prop; P1.4 for 1.5 & le; P & le; 5.0 MPa. The maximum carbon conversion to soot was related to pressure following the relationship eta s, max & prop; P0.55 for 1.5 & le; P & le; 5.0 MPa. The maximum value of carbon converted to soot was etas, max = 10.1% at P = 5.0 MPa. The maximum soot concentration was always found at a height approximately half way between the burner and the flame tip. The temperature was lower in high soot loading regions of the flame. For the same height in the flame, temperature decreased with increasing pressure.
Author: Marie Emma Vaillancourt Publisher: ISBN: 9780494210178 Category : Combustion Languages : en Pages : 190
Book Description
Measurements of soot concentration, flame temperature and flame geometry have been recorded for non-smoking methane-air laminar diffusion flames at pressures from P = 1.5 MPa to P = 6.0 MPa. Soot concentration and temperature profiles were obtained using the spectral soot emission diagnostic method and the Abel inversion deconvolution technique. Visual inspection and measurement of the flame revealed a slight increase in height and decrease in cross-section with increasing pressure. Soot volume fraction increased with pressure according to fv max & prop; P1.4 for 1.5 & le; P & le; 5.0 MPa. The maximum carbon conversion to soot was related to pressure following the relationship eta s, max & prop; P0.55 for 1.5 & le; P & le; 5.0 MPa. The maximum value of carbon converted to soot was etas, max = 10.1% at P = 5.0 MPa. The maximum soot concentration was always found at a height approximately half way between the burner and the flame tip. The temperature was lower in high soot loading regions of the flame. For the same height in the flame, temperature decreased with increasing pressure.
Author: Gorngrit Intasopa Publisher: ISBN: 9780494761816 Category : Languages : en Pages : 208
Book Description
Methane-air, ethane-air, and n-heptane-air over-ventilated co-flow laminar diffusion flames were studied up to pressures of 2.03, 1.52, and 0.51 MPa, respectively, to determine the effect of pressure on flame shape, soot concentration, and temperature. A spectral soot emission optical diagnostic method was used to obtain the spatially resolved soot formation and temperature data. In all cases, soot formation was enhanced by pressure, but the pressure sensitivity decreased as pressure was increased. The maximum fuel carbon conversion to soot, etamax, was approximated by a power law dependence with the pressure exponent of 0.92 between 0.51 and 1.01 MPa, and 0.68 between 1.01 and 2.03 MPa with etamax=9.5% at 2.03 MPa for methane-air flames. For ethane-air flames, the pressure exponent was 1.57 between 0.20 and 0.51 MPa, 1.08 between 0.51 and 1.01 MPa, and 0.58 between 1.01 and 1.52 MPa where etamax=23% at 1.52 MPa. For nitrogen-diluted n-heptane-air flames, etamax=6.5% at 0.51 MPa.
Author: Hyun Il Joo Publisher: ISBN: Category : Languages : en Pages :
Book Description
An experimental study was conducted using axisymmetric co-flow laminar diffusion flames of methane-air, methane-oxygen and ethylene-air to examine the effect of pressure on soot formation and the structure of the temperature field. A liquid fuel burner was designed and built to observe the sooting behavior of methanol-air and n-heptane-air laminar diffusion flames at elevated pressures up to 50 atm. A non-intrusive, line-of-sight spectral soot emission (SSE) diagnostic technique was used to determine the temperature and the soot volume fraction of methane-air flames up to 60 atm, methane-oxygen flames up to 90 atm and ethylene-air flames up to 35 atm. The physical flame structure of the methane-air and methane-oxygen diffusion flames were characterized over the pressure range of 10 to 100 atm and up to 35 atm for ethylene-air flames. The flame height, marked by the visible soot radiation emission, remained relatively constant for methane-air and ethylene-air flames over their respected pressure ranges, while the visible flame height for the methane-oxygen flames was reduced by over 50 % between 10 and 100 atm. During methane-air experiments, observations of anomalous occurrence of liquid material formation at 60 atm and above were recorded. The maximum conversion of the carbon in the fuel to soot exhibited a strong power-law dependence on pressure. At pressures 10 to 30 atm, the pressure exponent is approximately 0.73 for methane-air flames. At higher pressures, between 30 and 60 atm, the pressure exponent is approximately 0.33. The maximum fuel carbon conversion to soot is 12.6 % at 60 atm. For methane-oxygen flames, the pressure exponent is approximately 1.2 for pressures between 10 and 40 atm. At pressures between 50 and 70 atm, the pressure exponent is about -3.8 and approximately -12 for 70 to 90 atm. The maximum fuel carbon conversion to soot is 2 % at 40 atm. For ethylene-air flames, the pressure exponent is approximately 1.4 between 10 and 30 atm. The maximum carbon conversion to soot is approximately 6.5 % at 30 atm and remained constant at higher pressures.
Author: Publisher: ISBN: Category : Languages : en Pages :
Book Description
An experimental study was conducted using axisymmetric co-flow laminar diffusion flames of methane-air, methane-oxygen and ethylene-air to examine the effect of pressure on soot formation and the structure of the temperature field. A liquid fuel burner was designed and built to observe the sooting behavior of methanol-air and n-heptane-air laminar diffusion flames at elevated pressures up to 50 atm. A non-intrusive, line-of-sight spectral soot emission (SSE) diagnostic technique was used to determine the temperature and the soot volume fraction of methane-air flames up to 60 atm, methane-oxygen flames up to 90 atm and ethylene-air flames up to 35 atm. The physical flame structure of the methane-air and methane-oxygen diffusion flames were characterized over the pressure range of 10 to 100 atm and up to 35 atm for ethylene-air flames. The flame height, marked by the visible soot radiation emission, remained relatively constant for methane-air and ethylene-air flames over their respected pressure ranges, while the visible flame height for the methane-oxygen flames was reduced by over 50 % between 10 and 100 atm. During methane-air experiments, observations of anomalous occurrence of liquid material formation at 60 atm and above were recorded. The maximum conversion of the carbon in the fuel to soot exhibited a strong power-law dependence on pressure. At pressures 10 to 30 atm, the pressure exponent is approximately 0.73 for methane-air flames. At higher pressures, between 30 and 60 atm, the pressure exponent is approximately 0.33. The maximum fuel carbon conversion to soot is 12.6 % at 60 atm. For methane-oxygen flames, the pressure exponent is approximately 1.2 for pressures between 10 and 40 atm. At pressures between 50 and 70 atm, the pressure exponent is about -3.8 and approximately -12 for 70 to 90 atm. The maximum fuel carbon conversion to soot is 2 % at 40 atm. For ethylene-air flames, the pressure exponent is approximately 1.4 between 10 and 30 atm. The maximu.
Author: Paul Michael Mandatori Publisher: ISBN: 9780494160565 Category : Combustion Languages : en Pages : 198
Book Description
Ethane-air laminar coflow non-smoking diffusion flames have been studied at pressures up to 3.34 MPa to determine the effect of pressure on soot formation, flame temperatures and physical flame properties. The spectral soot emission (SSE) diagnostic was used to obtain spatially resolved (both radially and axially) soot volume fraction and soot temperature measurements at pressures of 0.20 to 3.34 MPa. In general, temperature profiles of a given height were found to decrease with increasing pressure. Pressure was found to enhance soot formation with decreased sensitivity as pressures were increased. A power law relation between maximum soot volume fraction and pressure was found to be fvmax & prop;P 2.39 for 0.20 & le; P & le; 1.52 MPa and fvmax & prop;P 1.10 for 1.52 & le; P & le; 3.34 MPa. The integrated line-of-sight soot volume fraction was found to vary as fvline, max & prop;P 2.32 for 0.20 & le; P & le; 0.51 MPa, fvline, max & prop;P 1.44 for 0.51 & le; P & le; 1.52 MPa and fvline, max & prop;P 0.95 for 1.52 & le; P & le; 3.34 MPa. The variation of maximum carbon conversion to soot, as a percentage of the fuel's carbon, was etas, max & prop; P2.23 for 0.20 & le; P & le; 1.13 MPa, etas, max & prop; P1.12 for 0.51 & le; P & le; 1.52 MPa and etas, max & prop; P0.41 for 1.52 & le; P & le; 3.34 MPa. The maximum value of carbon conversion was found to be eta s, max = 27.61% at P = 3.34 MPa.
Author: Decio S. (Decio Santos) Bento Publisher: Library and Archives Canada = Bibliothèque et Archives Canada ISBN: 9780494024430 Category : Combustion Languages : en Pages : 158
Book Description
Laminar axisymmetric propane air diffusion flames were studied at pressures 0.1 to 0.725 MPa (1 to 7.25 atm). To investigate the effect of pressure on soot formation, radially resolved soot temperatures and soot volume fractions were deduced from soot radiation emission scans collected at various pressures using spectral soot emission (SSE). Overall flame stability was quite good as judged by the naked eye. Flame heights varied by 15% and flame axial diameters decreased by 30% over the entire pressure range.Analysis of temperature sensitivity to variations in E lambda(m) revealed that a change in E lambda(m) of +/-20% produced a change in local temperature values of about 75 to 100 K or about 5%.Temperatures decreased and soot concentration increased with increased pressure. More specifically, the peak soot volume fraction showed a power law dependence, fv ∝ Pn where n = 2.0 over the entire pressure range. The maximum integrated soot volume fraction also showed a power law relationship with pressure, f ̄v ∝ Pn where n = 3.4 for 1 ≤ P ≤ 2 atm and n = 1.4 for 2 ≤ P ≤ 7.25 atm. The percentage of fuel carbon converted to soot increased with pressure at a rate, etas ∝ Pn where n = 3.3 and n = 1.1 for 1 ≤ P ≤ 2 atm and 2 ≤ P ≤ 7.25 atm respectively.
Author: Kevin Austen Thomson Publisher: Library and Archives Canada = Bibliothèque et Archives Canada ISBN: 9780494029565 Category : Languages : en Pages : 592
Author: Marie Emma Vaillancourt
Author: Marie Emma Vaillancourt
Author: Gorngrit Intasopa
Author: Hyun Il Joo
Author: 
Author: Paul Michael Mandatori![Soot Formation in Propane-air Laminar Diffusion Flames at Elevated Pressures [microform] PDF](https://books.google.com/books/content/images/frontcover/j8uMtgAACAAJ?fife=w80-h100)
Author: Decio S. (Decio Santos) Bento![Soot Formation in Annular Non-premixed Laminar Flames of Methane-air at Pressures of 0.1 to 4.0 MPa [microform] PDF](https://books.google.com/books/content/images/frontcover/3KHKwgEACAAJ?fife=w80-h100)
Author: Kevin Austen Thomson
Author: Marc Robert Joseph Charest
Author: Arup Barua
Author: Irvin M. Miller