Author: Publisher:
ISBN:
Category :
Languages : en
Pages :
Book Description
Growth Rates and Microstructural Characteristics of 300 C Rolled Uranium Rods on Thermal Cycling. Final Report on Part of Metallurgy Program 5.1.9
Author: The Effect of Cycling Variables Upon the Growth Rate of 300C Rolled Uranium
Author: R. M. MayfieldPublisher:
ISBN:
Category : Deformation (Mechanics)
Languages : en
Pages : 0
Book Description
This report contains the results of this investigation. The variables studied included (a) heating and cooling rates, (b) cycling temperature limits, (c) temperature range, and (d) holding times at each temperature.
The Effect of Cycling Variables Upon the Growth Rate of 3000 C Rolled Uranium
Author: R. M. MayfieldPublisher:
ISBN:
Category : Heat-transfer media
Languages : en
Pages : 28
Book Description
Mechanical Properties of Rolled Uranium Rods
Author: R. M. MayfieldPublisher:
ISBN:
Category : Nuclear fuel rods
Languages : en
Pages : 46
Book Description
Effects of Rolling and Heat Treatment on Anisotropic Irradiation Growth of Uranium. Final Report-Metallurgy Program 6.1.15
Author: Publisher:
ISBN:
Category :
Languages : en
Pages :
Book Description
An investigation was made to determine the effect of rolling temperature, roll pass design, amount of reduction, and heat treatment before and after rolling on the anisotropic growth rate of uranium under irradiation. The growth rate was found to increase with decreasing rolling temperature and with increasing reduction of area at 300 deg C. The rate of elongation was proportional to the amount of (0l0) component present or, where shortening occurred, to the amount of (l00) component. Oval-edgeoval roll passes resulted in somewhat higher irradiation growth rates than did round roll passes. Recrystallization after rolling effectively reduced the irradiation growth rate of uranium rolled at temperatures of 500 deg C and lower. Irradiation caused length shortening in uranium which was beta quenched after being round-rolled at temperatures of 400 deg C and above, and which was beta quenched after being oval- rolled at temperatures of 300 deg C and above. (auth).
The Effect of Cycling Variables Upon the Growth Rate of 300C Rolled Uranium
Author: R. M. MayfieldPublisher:
ISBN:
Category : Deformation (Mechanics)
Languages : en
Pages : 52
Book Description
This report contains the results of this investigation. The variables studied included (a) heating and cooling rates, (b) cycling temperature limits, (c) temperature range, and (d) holding times at each temperature.
EFFECT OF ROLLING TEMPERATURE ON THE PREFERRED ORIENTATION IN ROLLED URANIUM RODS. Final Report-Metallurgy Program 4.1.9
Author: Mechanical Properties of Ceramics
Author: John B. WachtmanPublisher: John Wiley & Sons
ISBN: 9780470451502
Category : Technology & Engineering
Languages : en
Pages : 496
Book Description
A Comprehensive and Self-Contained Treatment of the Theory and Practical Applications of Ceramic Materials When failure occurs in ceramic materials, it is often catastrophic, instantaneous, and total. Now in its Second Edition, this important book arms readers with a thorough and accurate understanding of the causes of these failures and how to design ceramics for failure avoidance. It systematically covers: Stress and strain Types of mechanical behavior Strength of defect-free solids Linear elastic fracture mechanics Measurements of elasticity, strength, and fracture toughness Subcritical crack propagation Toughening mechanisms in ceramics Effects of microstructure on toughness and strength Cyclic fatigue of ceramics Thermal stress and thermal shock in ceramics Fractography Dislocation and plastic deformation in ceramics Creep and superplasticity of ceramics Creep rupture at high temperatures and safe life design Hardness and wear And more While maintaining the first edition's reputation for being an indispensable professional resource, this new edition has been updated with sketches, explanations, figures, tables, summaries, and problem sets to make it more student-friendly as a textbook in undergraduate and graduate courses on the mechanical properties of ceramics.
Law of Corresponding States for Fused Salts
Author: H. ReissPublisher:
ISBN:
Category : Equations of state
Languages : en
Pages : 28
Book Description
The Science and Engineering of Materials
Author: Donald R. AskelandPublisher: Springer
ISBN: 1489928952
Category : Technology & Engineering
Languages : en
Pages : 870
Book Description
The Science and Engineering of Materials, Third Edition, continues the general theme of the earlier editions in providing an understanding of the relationship between structure, processing, and properties of materials. This text is intended for use by students of engineering rather than materials, at first degree level who have completed prerequisites in chemistry, physics, and mathematics. The author assumes these stu dents will have had little or no exposure to engineering sciences such as statics, dynamics, and mechanics. The material presented here admittedly cannot and should not be covered in a one-semester course. By selecting the appropriate topics, however, the instructor can emphasise metals, provide a general overview of materials, concentrate on mechani cal behaviour, or focus on physical properties. Additionally, the text provides the student with a useful reference for accompanying courses in manufacturing, design, or materials selection. In an introductory, survey text such as this, complex and comprehensive design problems cannot be realistically introduced because materials design and selection rely on many factors that come later in the student's curriculum. To introduce the student to elements of design, however, more than 100 examples dealing with materials selection and design considerations are included in this edition.