Growth of 3C-SiC Via a Hot-wall CVD Reactor PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Growth of 3C-SiC Via a Hot-wall CVD Reactor PDF full book. Access full book title Growth of 3C-SiC Via a Hot-wall CVD Reactor by Suzie Harvey. Download full books in PDF and EPUB format.
Author: Suzie Harvey Publisher: ISBN: Category : Languages : en Pages :
Book Description
ABSTRACT: The heteroepitaxial growth of cubic silicon carbide (3C-SiC) on silicon (Si) substrates at high growth rates, via a horizontal hot-wall chemical vapor deposition (CVD) reactor, has been achieved. The final growth process was developed in three stages; an initial "baseline" development stage, an optimization stage, and a large area growth stage. In all cases the growth was conducted using a two step, carbonization plus growth, process. During carbonization, the surface of the Si is converted to 3C-SiC, which helps to minimize the stress in the growing crystal. Propane (C3H8) and silane (SiH4), diluted in hydrogen (H2), were used as the carbon and silicon source, respectively. A deposition rate of approximately 10 um/h was established during the baseline process. Once the baseline process proved to be repeatable, optimization of the process began. Through variations in temperature, pressure, and the Si/C ratio, thick 3C-SiC films (up to 22 um thick) and high deposition rates (up to 30 um/h) were obtained. The optimized process was then applied to growth on 50 mm diameter Si(100) wafers. The grown 3C-SiC films were analyzed using a variety of characterization techniques. The thickness of the films was assessed through Fourier Transform infrared (FTIR) spectroscopy, and confirmed by cross-section scanning electron microscopy (SEM). The SEM cross-sections were also used to investigate the 3C-SiC/Si interface. The surface morphology of the films was inspected via Nomarsky interference optical microscopy, atomic force microscopy (AFM), and SEM. The crystalline quality of the films was determined through X-ray diffraction (XRD) and low-temperature photoluminescence (LTPL) analysis. A mercury probe was used to make non-contact CV/IV measurements and determine the film doping.
Author: Suzie Harvey Publisher: ISBN: Category : Languages : en Pages :
Book Description
ABSTRACT: The heteroepitaxial growth of cubic silicon carbide (3C-SiC) on silicon (Si) substrates at high growth rates, via a horizontal hot-wall chemical vapor deposition (CVD) reactor, has been achieved. The final growth process was developed in three stages; an initial "baseline" development stage, an optimization stage, and a large area growth stage. In all cases the growth was conducted using a two step, carbonization plus growth, process. During carbonization, the surface of the Si is converted to 3C-SiC, which helps to minimize the stress in the growing crystal. Propane (C3H8) and silane (SiH4), diluted in hydrogen (H2), were used as the carbon and silicon source, respectively. A deposition rate of approximately 10 um/h was established during the baseline process. Once the baseline process proved to be repeatable, optimization of the process began. Through variations in temperature, pressure, and the Si/C ratio, thick 3C-SiC films (up to 22 um thick) and high deposition rates (up to 30 um/h) were obtained. The optimized process was then applied to growth on 50 mm diameter Si(100) wafers. The grown 3C-SiC films were analyzed using a variety of characterization techniques. The thickness of the films was assessed through Fourier Transform infrared (FTIR) spectroscopy, and confirmed by cross-section scanning electron microscopy (SEM). The SEM cross-sections were also used to investigate the 3C-SiC/Si interface. The surface morphology of the films was inspected via Nomarsky interference optical microscopy, atomic force microscopy (AFM), and SEM. The crystalline quality of the films was determined through X-ray diffraction (XRD) and low-temperature photoluminescence (LTPL) analysis. A mercury probe was used to make non-contact CV/IV measurements and determine the film doping.
Author: Christopher L. Frewin Publisher: ISBN: Category : Languages : en Pages :
Book Description
ABSTRACT: Silicon carbide, SiC, is a semiconductor material which has many diverse uses in many of today's leading technologies. The wide band-gap aspect of the material has been utilized to create power and high frequency electronics, its physical hardness enables its use for MEMS devices, and the biological compatibility make perfect for utilization in medical applications. SiC is not a chemical compound normally found in nature and must be artificially generated. One of the methods used for the creation of single crystal, high quality SiC material is provided through the use of a chemical vapor deposition reactor. The University of South Florida currently has a horizontal hot-wallLPCVD reactor used by Dr. S.E. Saddow and his group to grow epitaxial SiC material for research grants by ONR and ARL. These agencies have commissioned the construction of a second LPCVD reactor for the primary purpose of growing 3C-SiC, a specific SiC crystal polytype, and this work describes the fabrication of the new reactor, MF2. This reactor was designed using the first reactor, MF1, as a template, but the design was modified to better facilitate single crystalline growth. The environment of the reactor is a very important consideration for crystal growth, and slight variations can cause critical defect incorporation into the crystal lattice. Many conditioning runs were required to facilitate the epitaxial growth of the different polytypes of SiC, and constant switching of the primary hot-zone required for the growth of hexagonal 4H-SiC and 6H-SiC to the hot zone required for 3C-SiC consumed precious resources and time. The new reactor uses a single primary control to monitor the three most important environmental concerns; hot-zone temperature, gaseous flow, and chamber pressure. The new reactor has been designed to use 100 mm Si substrates instead of the 50mm Si substrate size currently in use by MF1. The construction, testing, and 3C-SiC epitaxial growth on Si substrate capability of a 200 mm 3C-SiC hot-wall LPCVD reactor are demonstrated through this work.
Author: Robin Karhu Publisher: Linköping University Electronic Press ISBN: 9176851494 Category : Languages : en Pages : 40
Book Description
Silicon Carbide (SiC) is a wide bandgap semiconductor that has attracted a lot of interest for electronic applications due to its high thermal conductivity, high saturation electron drift velocity and high critical electric field strength. In recent years commercial SiC devices have started to make their way into high and medium voltage applications. Despite the advancements in SiC growth over the years, several issues remain. One of these issues is that the bulk grown SiC wafers are not suitable for electronic applications due to the high background doping and high density of basal plane dislocations (BPD). Due to these problems SiC for electronic devices must be grown by homoepitaxy. The epitaxial growth is performed in chemical vapor deposition (CVD) reactors. In this work, growth has been performed in a horizontal hot-wall CVD (HWCVD) reactor. In these reactors it is possible to produce high-quality SiC epitaxial layers within a wide range of doping, both n- and p-type. SiC is a well-known example of polytypism, where the different polytypes exist as different stacking sequences of the Si-C bilayers. Polytypism makes polytype stability a problem during growth of SiC. To maintain polytype stability during homoepitaxy of the hexagonal polytypes the substrates are usually cut so that the angle between the surface normal and the c-axis is a few degrees, typically 4 or 8°. The off-cut creates a high density of micro-steps at the surface. These steps allow for the replication of the substrates polytype into the growing epitaxial layer, the growth will take place in a step-flow manner. However, there are some drawbacks with step-flow growth. One is that BPDs can replicate from the substrate into the epitaxial layer. Another problem is that 4H-SiC is often used as a substrate for growth of GaN epitaxial layers. The epitaxial growth of GaN has been developed on on-axis substrates (surface normal coincides with c-axis), so epitaxial 4H-SiC layers grown on off-axis substrates cannot be used as substrates for GaN epitaxial growth. In efforts to solve the problems with off-axis homoepitaxy of 4H-SiC, on-axis homoepitaxy has been developed. In this work, further development of wafer-scale on-axis homoepitaxy has been made. This development has been made on a Si-face of 4H-SiC substrates. The advances include highly resistive epilayers grown on on-axis substrates. In this thesis the ability to control the surface morphology of epitaxial layers grown on on-axis homoepitaxy is demonstrated. This work also includes growth of isotopically enriched 4H-SiC on on-axis substrates, this has been done to increase the thermal conductivity of the grown epitaxial layers. In (paper 1) on-axis homoepitaxy of 4H-SiC has been developed on 100 mm diameter substrates. This paper also contains comparisons between different precursors. In (paper 2) we have further developed on-axis homoepitaxy on 100 mm diameter wafers, by doping the epitaxial layers with vanadium. The vanadium doping of the epitaxial layers makes the layers highly resistive and thus suitable to use as a substrate for III-nitride growth. In (paper 3) we developed a method to control the surface morphology and reduce the as-grown surface roughness in samples grown on on-axis substrates. In (paper 4) we have increased the thermal conductivity of 4H-SiC epitaxial layers by growing the layers using isotopically enriched precursors. In (paper 5) we have investigated the role chlorine have in homoepitaxial growth of 4H-SiC. In (paper 6) we have investigated the charge carrier lifetime in as-grown samples and traced variations in lifetime to structural defects in the substrate. In (paper 7) we have investigated the formation mechanism of a morphological defect in homoepitaxial grown 4H-SiC.
Author: Rachael L. Myers-Ward Publisher: ISBN: Category : Languages : en Pages :
Book Description
ABSTRACT: This dissertation research focused on the growth of 4H-SiC epitaxial layers in low-pressure horizontal hot-wall chemical vapor deposition (CVD) reactors. The goal of the research was to develop a growth process that maximized the growth rate and produced films of smooth morphology. The epitaxial growth of SiC was carried out in two different reactor sizes, a 75 mm reactor and a 200 mm reactor. The maximum repeatable growth rate achieved was 30-32 um/h in the 200 mm reactor using the standard chemistry of hydrogen-propane-silane (H2-C3H8-SiH4) at growth temperatures
Author: Stephen E. Saddow Publisher: Elsevier ISBN: 0123859069 Category : Medical Languages : en Pages : 496
Book Description
Silicon Carbide (SiC) is a wide-band-gap semiconductor biocompatible material that has the potential to advance advanced biomedical applications. SiC devices offer higher power densities and lower energy losses, enabling lighter, more compact and higher efficiency products for biocompatible and long-term in vivo applications ranging from heart stent coatings and bone implant scaffolds to neurological implants and sensors. The main problem facing the medical community today is the lack of biocompatible materials that are also capable of electronic operation. Such devices are currently implemented using silicon technology, which either has to be hermetically sealed so it cannot interact with the body or the material is only stable in vivo for short periods of time. For long term use (permanent implanted devices such as glucose sensors, brain-machine-interface devices, smart bone and organ implants) a more robust material that the body does not recognize and reject as a foreign (i.e., not organic) material is needed. Silicon Carbide has been proven to be just such a material and will open up a whole new host of fields by allowing the development of advanced biomedical devices never before possible for long-term use in vivo. This book not only provides the materials and biomedical engineering communities with a seminal reference book on SiC that they can use to further develop the technology, it also provides a technology resource for medical doctors and practitioners who are hungry to identify and implement advanced engineering solutions to their everyday medical problems that currently lack long term, cost effective solutions. Discusses Silicon Carbide biomedical materials and technology in terms of their properties, processing, characterization, and application, in one book, from leading professionals and scientists Critical assesses existing literature, patents and FDA approvals for clinical trials, enabling the rapid assimilation of important data from the current disparate sources and promoting the transition from technology research and development to clinical trials Explores long-term use and applications in vivo in devices and applications with advanced sensing and semiconducting properties, pointing to new product devekipment particularly within brain trauma, bone implants, sub-cutaneous sensors and advanced kidney dialysis devices
Author: Tsunenobu Kimoto Publisher: John Wiley & Sons ISBN: 1118313550 Category : Technology & Engineering Languages : en Pages : 565
Book Description
A comprehensive introduction and up-to-date reference to SiC power semiconductor devices covering topics from material properties to applications Based on a number of breakthroughs in SiC material science and fabrication technology in the 1980s and 1990s, the first SiC Schottky barrier diodes (SBDs) were released as commercial products in 2001. The SiC SBD market has grown significantly since that time, and SBDs are now used in a variety of power systems, particularly switch-mode power supplies and motor controls. SiC power MOSFETs entered commercial production in 2011, providing rugged, high-efficiency switches for high-frequency power systems. In this wide-ranging book, the authors draw on their considerable experience to present both an introduction to SiC materials, devices, and applications and an in-depth reference for scientists and engineers working in this fast-moving field. Fundamentals of Silicon Carbide Technology covers basic properties of SiC materials, processing technology, theory and analysis of practical devices, and an overview of the most important systems applications. Specifically included are: A complete discussion of SiC material properties, bulk crystal growth, epitaxial growth, device fabrication technology, and characterization techniques. Device physics and operating equations for Schottky diodes, pin diodes, JBS/MPS diodes, JFETs, MOSFETs, BJTs, IGBTs, and thyristors. A survey of power electronics applications, including switch-mode power supplies, motor drives, power converters for electric vehicles, and converters for renewable energy sources. Coverage of special applications, including microwave devices, high-temperature electronics, and rugged sensors. Fully illustrated throughout, the text is written by recognized experts with over 45 years of combined experience in SiC research and development. This book is intended for graduate students and researchers in crystal growth, material science, and semiconductor device technology. The book is also useful for design engineers, application engineers, and product managers in areas such as power supplies, converter and inverter design, electric vehicle technology, high-temperature electronics, sensors, and smart grid technology.
Author: Govindhan Dhanaraj Publisher: Springer Science & Business Media ISBN: 3540747613 Category : Science Languages : en Pages : 1823
Book Description
Over the years, many successful attempts have been chapters in this part describe the well-known processes made to describe the art and science of crystal growth, such as Czochralski, Kyropoulos, Bridgman, and o- and many review articles, monographs, symposium v- ing zone, and focus speci cally on recent advances in umes, and handbooks have been published to present improving these methodologies such as application of comprehensive reviews of the advances made in this magnetic elds, orientation of the growth axis, intro- eld. These publications are testament to the grow- duction of a pedestal, and shaped growth. They also ing interest in both bulk and thin- lm crystals because cover a wide range of materials from silicon and III–V of their electronic, optical, mechanical, microstructural, compounds to oxides and uorides. and other properties, and their diverse scienti c and The third part, Part C of the book, focuses on - technological applications. Indeed, most modern ad- lution growth. The various aspects of hydrothermal vances in semiconductor and optical devices would growth are discussed in two chapters, while three other not have been possible without the development of chapters present an overview of the nonlinear and laser many elemental, binary, ternary, and other compound crystals, KTP and KDP. The knowledge on the effect of crystals of varying properties and large sizes. The gravity on solution growth is presented through a c- literature devoted to basic understanding of growth parison of growth on Earth versus in a microgravity mechanisms, defect formation, and growth processes environment.
Author: Publisher: Academic Press ISBN: 0080864503 Category : Technology & Engineering Languages : en Pages : 435
Book Description
This volume addresses the subject of materials science, specifically the materials aspects, device applications, and fabricating technology of SiC.
Author: Suzie Harvey
Author: Suzie Harvey
Author: Christopher Locke
Author: Christopher L. Frewin
Author: Robin Karhu
Author: Rachael L. Myers-Ward
Author: Stephen E. Saddow
Author: Tsunenobu Kimoto
Author: Govindhan Dhanaraj
Author: K. Shenai
Author: