Fatigue Crack Growth of Low-alloy Steels in Light Water Reactor Environments PDF Download

Author: E. E. Nelson
Publisher:
ISBN:
Category :
Languages : en
Pages : 51

View

Book Description

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 23

View

Book Description
Section 111 of the ASME Boiler and Pressure Vessel Code specifies fatigue design curves for structural materials. The effects of reactor coolant environments are not explicitly addressed by the Code design curves. Recent test data illustrate potentially significant effects of light water reactor (LWR) coolant environments on the fatigue resistance of carbon and low-alloy steels. Under certain loading and environmental conditions, fatigue lives of test specimens may be shorter than those in air by a factor of H"0. The crack initiation and crack growth characteristics of carbon and low-alloy steels in LWR environments are presented. Decreases in fatigue life of these steels in high-dissolved-oxygen water are caused primarily by the effect of environment on growth of short cracks

Author: William Alan Van der Sluys
Publisher: ASTM International
ISBN: 0803124082
Category : Metals
Languages : en
Pages : 304

View

Book Description

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 22

View

Book Description
Fatigue and stress corrosion cracking (SCC) for low-alloy steel used in piping and in steam generator and reactor pressure vessels have been investigated. Fatigue data were obtained on medium-sulfur-content A533-Gr B and A106-Gr B steels in high-purity (HP) deoxygenated water, in simulated pressurized water reactor water, and in air. Analytical studies focused on the behavior of carbon steels in boiling water reactor (BWR) environments. Crack-growth rates of composite fracture-mechanics specimens of A533-Gr B/Inconel-182/Inconel-600 (plated with nickel) and homogeneous specimens of A533-Gr B steel were determined under small-amplitude cyclic loading in HP water with ≈300 pbb dissolved oxygen. Radiation-induced segregation and irradiation-assisted SCC of Type 304 SS after accumulation of relatively high fluence also have been investigated. Microchemical and microstructural changes in HP and commercial-purity Type 304 SS specimens from control-blade absorber tubes used in two operating BWRs were studied by Auger electron spectroscopy and scanning electron microscopy, and slow-strain-rate tensile tests were conducted on tubular specimens in air and in simulated BWR water at 289°C.

Author: Welding Research Council (U.S.)
Publisher:
ISBN:
Category : Welding
Languages : en
Pages : 60

View

Book Description

Author: D Féron
Publisher: Woodhead Publishing
ISBN:
Category : Technology & Engineering
Languages : en
Pages : 378

View

Book Description
Stress corrosion cracking is a major problem in light water nuclear reactors, whether pressurised water reactors (PWRs) or boiling water reactors (BWRs). The nuclear industry needs to be able to predict the service life of these power plants and develop appropriate maintenance and repair practices to ensure safe long term operation. This important book sums up key recent research on corrosion in light water reactors and its practical applications. The book is divided into four parts. It begins with an overview of materials degradation due to stress corrosion, corrosion potential monitoring and passivation. Part two summarises research on susceptibility of materials to stress corrosion cracking and the ways it can be initiated. The third part of the book considers stress corrosion crack propagation processes whilst the final part includes practical case studies of corrosion in particular plants. The book reviews corrosion in a range of materials such as low alloy steels, stainless steels and nickel-based alloys. With its distinguished editor and team of contributors, Corrosion issues in light water reactors is a standard work for the nuclear industry. Summarises key recent research on corrosion in light water reactors Includes practical case studies

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :

View

Book Description

Author: WH. Cullen
Publisher:
ISBN:
Category : Aluminum alloys
Languages : en
Pages : 22

View

Book Description
This paper presents an overview of the effect of light-water reactor environments on the fatigue crack growth rate in reactor pressure vessel steels. The effect of different variables known to influence the environmental assistance--stress intensity range, load ratio, frequency, temperature, water chemistry, and irradiation--is described. The fractographic phenomena and mechanisms of fatigue crack propagation associated with environmental influence is emphasized. An analytical approach for predicting the crack growth rates based on the hydrogen embrittlement model is described. Finally, a discussion of the effect of different transients occurring in the nuclear reactors on the crack growth rate predictions is presented.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :

View

Book Description
This report summarizes work performed by Argonne National Laboratory on fatigue and environmentally assisted cracking (EAC) in light water reactors (LWRs) from July 2000 to December 2000. Topics that have been investigated include (a) environmental effects on fatigue S-N behavior of primary pressure boundary materials, (b) irradiation-assisted stress corrosion cracking (IASCC) of austenitic stainless steels (SSs), and (c) EAC of Alloys 600 and 690. The fatigue strain-vs.-life data are summarized for the effects of various material, loading, and environmental parameters on the fatigue lives of carbon and low-alloy steels and austenitic SSs. Effects of the reactor coolant environment on the mechanism of fatigue crack initiation are discussed. Two methods for incorporating the effects of LWR coolant environments into the ASME Code fatigue evaluations are presented. Slow-strain-rate tensile tests and posttest fractographic analyses were conducted on several model SS alloys irradiated to (almost equal to)0.9 x 1021 n · cm−2 (E> 1 MeV) in He at 289 C in the Halden reactor. The results were used to determine the influence of alloying and impurity elements on the susceptibility of these steels to IASCC. A fracture toughness J-R curve test was conducted on a commercial heat of Type 304 SS that was irradiated to (almost equal to)2.0 x 1021 n · cm−2 in the Halden reactor. The results were compared with the data obtained earlier on steels irradiated to 0.3 and 0.9 x 1021 n · cm−2 (E> 1 MeV) (0.45 and 1.35 dpa). Neutron irradiation at 288 C was found to decrease the fracture toughness of austenitic SSs. Tests were conducted on compact-tension specimens of Alloy 600 under cyclic loading to evaluate the enhancement of crack growth rates in LWR environments. Then, the existing fatigue crack growth data on Alloys 600 and 690 were analyzed to establish the effects of temperature, load ratio, frequency, and stress intensity range on crack growth rates in air.

Author: W. H. Cullen
Publisher:
ISBN:
Category : Fractography
Languages : en
Pages : 134

View

Book Description
Fatigue crack growth data sets, for pressure vessel and piping steels, in reactor-grade water environment have appeared in various reports and publications since about 1972. All of the results which have been published from 1972 through 1979 have been plotted and are presented in this report. Beginning with a discussion of the need for these data, and an explanation of the laboratory facilities which are required for this research, this report goes on to describe the overall trends which have evolved through consideration of the data sets and the conditions under which they were generated. A model for hydrogen assisted fatigue crack growth is described and applied to the pressurized water reactor type of environment. A complete listing of references is included in the report. (Author).