Author: Prasanna Chinnathambi Publisher: ISBN: 9781687981233 Category : Electronic dissertations Languages : en Pages : 262
Book Description
In the first part of this work, ignition of methane-air mixtures under excess air dilution is studied. When excess air is used in SI engine operation, thermal efficiency is increased due to increase in compression ratio together with reduced pumping and heat loses. However, stable operation with excess air is challenging due to poor flammability of the resulting diluted mixture. Hence in order to achieve stable and complete combustion a turbulent jet ignition (TJI) system is used to improve combustion of lean methane-air mixtures. Various nozzle designs and operating strategies for a TJI system were tested in a rapid compression machine. 10-90% burn duration measurements were useful in assessing the performance of the nozzle designs while the 0-10% burn durations indicated if optimal air-fuel ratio is achieved within the pre-chamber at the time of ignition. The results indicated that distributed-jets TJI system offered faster and stable combustion while the concentrated-jets TJI system offered better dilution tolerance.Knock in a SI engine occurs due to autoignition of the end gas mixture and typically occurs in the negative temperature coefficient (NTC) region of the fuel-air mixture. Dilution of intake charge with cold exhaust recirculation gases (EGR) reduces combustion temperatures and decreases mixture reactivity thereby reducing knocking tendency. This enables optimal spark timings to be used, thereby increasing efficiency of SI engines which would otherwise be knock limited. Effect of cold EGR dilution is studied in the RCM by measuring the autoignition delay times of gasoline and gasoline surrogate mixtures diluted with varying levels of CO2. The autoignition experiments in the RCM were performed using a novel direct test chamber (DTC) charge preparation approach. The DTC approach enabled mixture preparation directly within the combustion chamber and eliminated the need for mixing tanks. Effect of CO2 dilution in retarding the autoignition delay times was more pronounced in the NTC region, while it was weaker in the low temperature and high temperature regions. The retarding effect was found to be dependent on both the octane number and the fuel composition of the gasoline being studied.Finally, the effect of substituting ethanol(biofuel) in gasoline surrogates for up to 40% by volume is studied. Ethanol is an octane booster, but it blends antagonistically with aromatics such as toluene and synergistically with alkanes with respect to the resulting octane number of the blends. In order to study this blending effect, two gasoline surrogates containing only alkanes (PRF), and alkanes with large amounts of toluene (TRF) are blended with varying levels of ethanol. The ignition delay times of the resulting mixtures are measured in a rapid compression machine and kinetic analysis was carried out using numerical simulations. The kinetic analysis revealed that ethanol controlled the final stages of ignition for the PRF blends when more than 10% by volume of ethanol is present. However, in the TRF blends, toluene controlled the ignition until mole fractions of ethanol became higher than the toluene indicating the reason for the antagonistic blending nature. It was found that the RON values of the resulting blends matched the trend of the ignition delay times recorded at 740K and 21 bar compressed conditions. This enables qualitative assessment of the RON numbers for new biofuel blends by measuring their ignition delay times in the RCM.
Author: Publisher: ISBN: Category : Languages : en Pages : 14
Book Description
The use of gasoline in homogeneous charge compression ignition engines (HCCI) and in duel fuel diesel - gasoline engines, has increased the need to understand its compression ignition processes under engine-like conditions. These processes need to be studied under well-controlled conditions in order to quantify low temperature heat release and to provide fundamental validation data for chemical kinetic models. With this in mind, an experimental campaign has been undertaken in a rapid compression machine (RCM) to measure the ignition of gasoline mixtures over a wide range of compression temperatures and for different compression pressures. By measuring the pressure history during ignition, information on the first stage ignition (when observed) and second stage ignition are captured along with information on the phasing of the heat release. Heat release processes during ignition are important because gasoline is known to exhibit low temperature heat release, intermediate temperature heat release and high temperature heat release. In an HCCI engine, the occurrence of low-temperature and intermediate-temperature heat release can be exploited to obtain higher load operation and has become a topic of much interest for engine researchers. Consequently, it is important to understand these processes under well-controlled conditions. A four-component gasoline surrogate model (including n-heptane, iso-octane, toluene, and 2-pentene) has been developed to simulate real gasolines. An appropriate surrogate mixture of the four components has been developed to simulate the specific gasoline used in the RCM experiments. This chemical kinetic surrogate model was then used to simulate the RCM experimental results for real gasoline. The experimental and modeling results covered ultra-lean to stoichiometric mixtures, compressed temperatures of 640-950 K, and compression pressures of 20 and 40 bar. The agreement between the experiments and model is encouraging in terms of first-stage (when observed) and second-stage ignition delay times and of heat release rate. The experimental and computational results are used to gain insight into low and intermediate temperature processes during gasoline ignition.
Author: Colin Banyon Publisher: ISBN: Category : Combustion engineering Languages : en Pages :
Book Description
Rapid compression machines (RCMs) are well characterized laboratory scale devices capable of achieving internal combustion (IC) engine relevant thermodynamic environments. These machines are often used to collect ignition delay times as targets for gas-phase chemical kinetic fuel autoigntion models. Modern RCMs utilize creviced piston(s) to improve charge homogeneity and allow for an adequate validation of detailed chemistry mechanisms against experiments using computationally efficient, homogeneous reactor models (HRMs). Conventionally, experiments are preformed by introducing a premixed gas of fuel + oxidizer + diluent into the machine, which is compressed volumetrically via a piston. Experiments investigating low-vapor pressure fuels (e.g. diesels, biodiesels, jet fuels, etc.) and surrogates can be conducted by preheating both the charge as well as the machine. This method of fuel loading can lead to pretest fuel pyrolysis as well as machine seal degradation. Under some conditions loading a fuel aerosol of finely atomized liquid droplets in an oxidizer + diluent bath gas (i.e. wet compression) has been suggested to extend the capabilities of RCM experiments to involatile fuels. This work investigates phase-change effects during RCM experiments, especially for aerosol-fueling conditions, while the methodology can be applied to gas-phase fuel experiments where fuel condensation can occur at the compressed conditions within the boundary layer region. To facilitate this study a reduced-order, physics-based model is used. This work highlights important machine-scale influences not investigated in previous work, and provides additional detail concerning an aerosol RCM{u2019}s capabilities and limitations. A transient formulation is developed for the multi-phase transport within the RCM reaction chamber as well as the flow to the piston crevice region during both the compression and delay periods. The goal of this work is threefold. First, an a priori knowledge of the stratification present under various conditions can help determine an optimum machine geometry so that discrepancies between experimental data sets and 0D kinetics simulations are minimized for involatile fuels. Second, the model is computationally tractable to prescribe heat loss rates to an HRM during simulations of experiments so that physical effects can be incorporated into simulations using detailed chemistry. Finally, heat loss rates that are prescribed to the HRM are only a function of machine geometry, and are independent of ad hoc and empirically derived fits that vary between facilities. Thus a more adequate comparison of data between RCM facilities and with existing literature can be made.
Author: Ting Wang Publisher: Woodhead Publishing ISBN: 0081001851 Category : Technology & Engineering Languages : en Pages : 929
Book Description
Integrated Gasification Combined Cycle (IGCC) Technologies discusses this innovative power generation technology that combines modern coal gasification technology with both gas turbine and steam turbine power generation, an important emerging technology which has the potential to significantly improve the efficiencies and emissions of coal power plants. The advantages of this technology over conventional pulverized coal power plants include fuel flexibility, greater efficiencies, and very low pollutant emissions. The book reviews the current status and future developments of key technologies involved in IGCC plants and how they can be integrated to maximize efficiency and reduce the cost of electricity generation in a carbon-constrained world. The first part of this book introduces the principles of IGCC systems and the fuel types for use in IGCC systems. The second part covers syngas production within IGCC systems. The third part looks at syngas cleaning, the separation of CO2 and hydrogen enrichment, with final sections describing the gas turbine combined cycle and presenting several case studies of existing IGCC plants. Provides an in-depth, multi-contributor overview of integrated gasification combined cycle technologies Reviews the current status and future developments of key technologies involved in IGCC plants Provides several case studies of existing IGCC plants around the world
Author: Publisher: ISBN: Category : Automobiles Languages : en Pages : 750
Book Description
Online version: Technical papers portion of the SAE Digital Library references thousands of SAE Technical Papers covering the latest advances and research in all areas of mobility engineering including ground vehicle, aerospace, off-highway, and manufacturing technology. Sample coverage includes fuels and lubricants, emissions, electronics, brakes, restraint systems, noise, engines, materials, lighting, and more. Your SAE service includes detailed summaries, complete documents in PDF, plus document storage and maintenance
Author: National Research Council Publisher: National Academies Press ISBN: 0309216389 Category : Science Languages : en Pages : 373
Book Description
Various combinations of commercially available technologies could greatly reduce fuel consumption in passenger cars, sport-utility vehicles, minivans, and other light-duty vehicles without compromising vehicle performance or safety. Assessment of Technologies for Improving Light Duty Vehicle Fuel Economy estimates the potential fuel savings and costs to consumers of available technology combinations for three types of engines: spark-ignition gasoline, compression-ignition diesel, and hybrid. According to its estimates, adopting the full combination of improved technologies in medium and large cars and pickup trucks with spark-ignition engines could reduce fuel consumption by 29 percent at an additional cost of $2,200 to the consumer. Replacing spark-ignition engines with diesel engines and components would yield fuel savings of about 37 percent at an added cost of approximately $5,900 per vehicle, and replacing spark-ignition engines with hybrid engines and components would reduce fuel consumption by 43 percent at an increase of $6,000 per vehicle. The book focuses on fuel consumption-the amount of fuel consumed in a given driving distance-because energy savings are directly related to the amount of fuel used. In contrast, fuel economy measures how far a vehicle will travel with a gallon of fuel. Because fuel consumption data indicate money saved on fuel purchases and reductions in carbon dioxide emissions, the book finds that vehicle stickers should provide consumers with fuel consumption data in addition to fuel economy information.
Author: M.J. Pilling Publisher: Elsevier ISBN: 0080535658 Category : Science Languages : en Pages : 823
Book Description
Combustion has played a central role in the development of our civilization which it maintains today as its predominant source of energy. The aim of this book is to provide an understanding of both fundamental and applied aspects of low-temperature combustion chemistry and autoignition. The topic is rooted in classical observational science and has grown, through an increasing understanding of the linkage of the phenomenology to coupled chemical reactions, to quite profound advances in the chemical kinetics of both complex and elementary reactions. The driving force has been both the intrinsic interest of an old and intriguing phenomenon and the centrality of its applications to our economic prosperity. The volume provides a coherent view of the subject while, at the same time, each chapter is self-contained.
Author: Prasanna Chinnathambi
Author: 
Author: Colin Banyon
Author: Ting Wang
Author: 
Author: National Research Council
Author: 
Author: 
Author: Chaitanya Wadkar
Author: M.J. Pilling