Experimental Study of Acid Fracture Conductivity of Austin Chalk Formation PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Experimental Study of Acid Fracture Conductivity of Austin Chalk Formation PDF full book. Access full book title Experimental Study of Acid Fracture Conductivity of Austin Chalk Formation by Andrea Nino Penaloza. Download full books in PDF and EPUB format.
Author: Andrea Nino Penaloza Publisher: ISBN: Category : Languages : en Pages : 90
Book Description
Acid fracture conductivity and the effect of key variables in the etching process during acid fracturing can be assessed at the laboratory scale. This is accomplished by using an experimental apparatus that simulates acid injection fluxes comparable to those in actual acid fracture treatments. After acid etching, fracture conductivity is measured at different closure stresses. This research work presents a systematic study to investigate the effect of temperature, rock-acid contact time and initial condition of the fracture surfaces on acid fracture conductivity in the Austin Chalk formation. While temperature and rock-acid contact are variables normally studied in fracture conductivity tests, the effect of the initial condition of the fracture surface has not been extensively investigated. The experimental results showed that there is no significant difference in acid fracture conductivity at high closure stress using smooth or rough fracture surfaces. In addition, we analyzed the mechanisms of acid etching and resulting conductivity creation in the two types of fracture surfaces studied by using surface profiles. For smooth surfaces, the mechanism of conductivity creation seems connected to uneven etching of the rock and roughness generation. For rough surfaces, acid conductivity is related to smoothing and deepening of the initial features on the sample surface than by creating more roughness. Finally, we compared the experimental results with Nirode-Kruk correlation for acid fracture conductivity. The electronic version of this dissertation is accessible from http://hdl.handle.net/1969.1/149578
Author: Andrea Nino Penaloza Publisher: ISBN: Category : Languages : en Pages : 90
Book Description
Acid fracture conductivity and the effect of key variables in the etching process during acid fracturing can be assessed at the laboratory scale. This is accomplished by using an experimental apparatus that simulates acid injection fluxes comparable to those in actual acid fracture treatments. After acid etching, fracture conductivity is measured at different closure stresses. This research work presents a systematic study to investigate the effect of temperature, rock-acid contact time and initial condition of the fracture surfaces on acid fracture conductivity in the Austin Chalk formation. While temperature and rock-acid contact are variables normally studied in fracture conductivity tests, the effect of the initial condition of the fracture surface has not been extensively investigated. The experimental results showed that there is no significant difference in acid fracture conductivity at high closure stress using smooth or rough fracture surfaces. In addition, we analyzed the mechanisms of acid etching and resulting conductivity creation in the two types of fracture surfaces studied by using surface profiles. For smooth surfaces, the mechanism of conductivity creation seems connected to uneven etching of the rock and roughness generation. For rough surfaces, acid conductivity is related to smoothing and deepening of the initial features on the sample surface than by creating more roughness. Finally, we compared the experimental results with Nirode-Kruk correlation for acid fracture conductivity. The electronic version of this dissertation is accessible from http://hdl.handle.net/1969.1/149578
Author: Maysam Pournik Publisher: ISBN: Category : Languages : en Pages :
Book Description
Success of acid fracturing treatment depends greatly on the created conductivity under closure stress. In order to have sufficient conductivity, the fracture face must be non-uniformly etched while the fracture strength maintained to withstand the closure stress. While there have been several experimental studies conducted on acid fracturing, most of these have not scaled experiments to field conditions and did not account for the effect of rock weakening and etching pattern. Hence, acid fracture conductivity predictions based on the above works have not been able to match actual results. In order to develop a more appropriate and accurate prediction of acid fracturing treatment outcome, a laboratory facility was developed that is properly scaled to field conditions and enables analysis of etching pattern and rock strength. A systematic experimental study that covered a variety of formations, acid types, and acid contact times was conducted. An acid fracture conductivity correlation was developed based on etched volume, etched pattern, and fracture strength under closure stress. Results suggested that there is an optimal time of acid exposure resulting in maximum fracture conductivity. There were large differences in the conductivity created with the different acid systems tested due to different etching patterns and degree of rock strength weakening. There was an optimal acid system depending on formation type, contact time and overburden stress. The acid fracture conductivities measured did not agree with the predictions of the Nierode-Kruk correlation. The newly developed correlation predicts conductivity much closer as it includes the effect of rock strength and surface etching pattern on resulting conductivity.
Author: Maria Georgina Melendez Castillo Publisher: ISBN: Category : Languages : en Pages :
Book Description
The conductivity created in acid fracturing is a competition between two phenomena: etching of the rock surface and weakening of the rock. This study presents experimental results of acid fracturing conductivity experiments with polymer gelled acid, while varying contact time and rock type. The experiments were conducted in a laboratory facility properly scaled from field to laboratory conditions to account for the hydrodynamic effects that take place in the field. The rocks of study were Indiana limestone, San Andres dolomite and Texas Cream chalk. Our results illustrate that acid fracturing conductivity is governed by the etching pattern of the rock surface and influenced by the hardness of the rock. If channels are created, the fracture is more likely to retain conductivity after closure. The hardness of the rock is the dominating factor to determine the conductivity response when no channeling is present. Among the rocks tested, Texas Cream chalk had the lowest hardness measurement before and after acidizing and the fracture closed at a much lower stress compared with limestone and dolomite. Dolomite had the highest conductivity under all closure stresses even without a channeling pattern. Additionally, it was observed that a higher reduction in rock strength at the contact points for dolomite yielded lower conductivity after closure. The effects of hardness variation on conductivity are higher in dolomite than in limestone and chalk. It is apparent that longer contact times do not always provide higher conductivity after closure.
Author: Publisher: ISBN: Category : Languages : en Pages : 107
Book Description
Austin chalk core has been tested to determine the effective law for deformation of the matrix material and the stress-sensitive conductivity of the natural fractures. For deformation behavior, two samples provided data on the variations of the poroelastic parameter, [alpha], for Austin chalk, giving values around 0.4. The effective-stress-law behavior of a Saratoga limestone sample was also measured for the purpose of obtaining a comparison with a somewhat more porous carbonate rock. [alpha] for this rock was found to be near 0.9. The low [alpha] for the Austin chalk suggests that stresses in the reservoir, or around the wellbore, will not change much with changes in pore pressure, as the contribution of the fluid pressure is small. Three natural fractures from the Austin chalk were tested, but two of the fractures were very tight and probably do not contribute much to production. The third sample was highly conductive and showed some stress sensitivity with a factor of three reduction in conductivity over a net stress increase of 3000 psi. Natural fractures also showed a propensity for permanent damage when net stressed exceeded about 3000 psi. This damage was irreversible and significantly affected conductivity. [alpha] was difficult to determine and most tests were inconclusive, although the results from one sample suggested that [alpha] was near unity.
Author: Ali Mansour A. Almomen Publisher: ISBN: Category : Languages : en Pages : 92
Book Description
Fracture conductivity and the effects of treatment variables can be studied in the laboratory. We conducted experiments based on scaling down the field conditions to laboratory scale by matching Reynold's and Peclet numbers. Experiments conducted were comprised of three stages: dynamic etching, surface characterization of etched cores, and conductivity measurement. The effect of initial condition of fracture surfaces on the etching pattern and conductivity were investigated in this study. Another area of interest is the variation of conductivity along the fracture due to acid spending. We also investigated the contact time, acid system type, and treatment temperature effects on conductivity using San Andres dolomite cores. The results from these studies showed that rough-surface fractures generate higher conductivity by an order of magnitude compared with a smooth-surface fracture at low-closure stress. Also, conductivity generated on rough-surface fractures by smoothing peaks and deepening valleys which widen the gap between the fracture surfaces after closure and acid creates conductivity on smooth-surface fractures by differential etching that creates asperities. The results suggest that an increase in acid spending does not automatically result in lower conductivity; and etched volume alone is not adequate to predicate the conductivity. Conductivity results from a combination of etching pattern, etched volume, and rock compressive strength after etching. In-situ crosslinked acid was found to be more effective in etching rock and controlling acid leakoff compared with linear-gelled acid. Also, crosslinked acid reduces the number of pits and the pit diameters. Based on conductivity tests, linear-gelled acid is more favorable at higher temperatures while in-situ crosslinked acid showed higher conductivity at lower temperatures. For a rough-surface fracture, shorter contact time created high conductivity compared to longer contact while injecting the same volume of acid, suggesting the existence of an optimum contact time. The electronic version of this dissertation is accessible from http://hdl.handle.net/1969.1/151186
Author: Obadare O Awoleke Publisher: ISBN: Category : Languages : en Pages :
Book Description
This work is about fracture conductivity; how to measure and model it based on experimental data. It is also about how to determine the relative importance of the factors that affect its magnitude and how to predict its magnitude based on these factors. We dynamically placed the slurry hereby simulating the slurry placement procedure in a field-scale fracture. We also used factorial and fractional factorial designs as the basis of our experimental investigation. The analysis and interpretation of experimental results take into account the stochastic nature of the process. We found that the relative importance of the investigated factors is dependent on the presence of outliers and how they are handled. Based on our investigation we concluded that the investigated factors arranged in order of decreasing impact on conductivity are: closure stress, polymer loading, flow back rate, presence of breaker, temperature and proppant concentration. In particular, we find that at high temperatures, fracture conductivity was severely reduced due to the formation of a dense proppant-polymer cake. Also, dehydration of the residual gel in the fracture at high flow back rates appears to cause severe damage to conductivity at higher temperatures. This represents a new way of thinking about the fracture cleanup process; not only as a displacement process, but also as a displacement and evaporative process. In engineering practice, this implies that aggressive flow back schemes are not necessarily beneficial for conductivity development. Also, we find that at low proppant concentrations, there is the increased likelihood of the formation of channels and high porosity fractures resulting in high fracture conductivities. The uniqueness of this work is a focus on the development of a conductivity model using regression analysis and also the illustration of a procedure that can be used to develop a conductivity model using dimensional analysis. We reviewed both methodologies and applied them to the challenge of modeling fracture conductivity from experimental studies. The electronic version of this dissertation is accessible from http://hdl.handle.net/1969.1/149287
Author: Andres Eduardo Pieve La Rosa Publisher: ISBN: Category : Languages : en Pages :
Book Description
This investigation carried out the analysis of fracture conductivity in a tight reservoir using laboratory experiments, by applying the procedure known as the dynamic fracture conductivity test. Considering the large number of experiments necessary to evaluate the effect of each parameter and the possible interaction of their combinations, the schedules of experiments were planned using a fractional factorial design. This design is used during the initial stage of studies to identify and discharge those factors that have little or no effect. Finally, the most important factors can then be studied in more detail during subsequent experiments. The objectives of this investigation were focused on identifying the effect of formation parameters such as closure stress, and temperature and fracture fluid parameters such as proppant loading over the final conductivity of a hydraulic fracture treatment. With the purpose of estimating the relation between fracture conductivity and the design parameters, two series of experiments were performed. The first set of experiments estimated the effects of the aliases parameters. The isolated effect of each independent parameter was obtained after the culmination of the second set of experiments. The preliminary test results indicated that the parameters with major negative effect over the final conductivity were closure stress and temperature. Some additional results show that proppant distribution had a considerable role over the final fracture conductivity when a low proppant concentration was used. Channels and void spaces in the proppant pack were detected on these cases improving the conductivity of the fracture, by creating paths of high permeability. It was observed that with experiments at temperatures around 250 degrees F, the unbroken gel dried up creating permeable scales that resulted in a significant loss in conductivity. The results of this investigation demonstrated that dynamic fracture conductivity test procedure is an excellent tool to more accurately represent the effects of design parameters over the fracture conductivity. These results are also the first step in the development of a statistical model that can be used to predict dynamic fracture conductivity.
Author: Andrea Nino Penaloza
Author: Andrea Nino Penaloza
Author: Maysam Pournik
Author: Maria Georgina Melendez Castillo
Author: 
Author: Ali Mansour A. Almomen
Author: 
Author: Obadare O Awoleke
Author: Andres Eduardo Pieve La Rosa
Author: Kevin Corbett
Author: