Experimental Investigation of Turbine Blade Platform Film Cooling and Rotational Effect on Trailing Edge Internal Cooling PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Experimental Investigation of Turbine Blade Platform Film Cooling and Rotational Effect on Trailing Edge Internal Cooling PDF full book. Access full book title Experimental Investigation of Turbine Blade Platform Film Cooling and Rotational Effect on Trailing Edge Internal Cooling by Lesley Mae Wright. Download full books in PDF and EPUB format.
Author: Lesley Mae Wright Publisher: ISBN: Category : Languages : en Pages :
Book Description
The present work has been an experimental investigation to evaluate the applicability of gas turbine cooling technology. With the temperature of the mainstream gas entering the turbine elevated above the melting temperature of the metal components, these components must be cooled, so they can withstand prolonged exposure to the mainstream gas. Both external and internal cooling techniques have been studied as a means to increase the life of turbine components. Detailed film cooling effectiveness distributions have been obtained on the turbine blade platform with a variety of cooling configurations. Because the newly developed pressure sensitive paint (PSP) technique has proven to be the most suitable technique for measuring the film effectiveness, it was applied to a variety of platform seal configurations and discrete film flows. From the measurements it was shown advanced seals provide more uniform protection through the passage with less potential for ingestion of the hot mainstream gases into the engine cavity. In addition to protecting the outer surface of the turbine components, via film cooling, heat can also be removed from the components internally. Because the turbine blades are rotating within the engine, it is important to consider the effect of rotation on the heat transfer enhancement within the airfoil cooling channels. Through this experimental investigation, the heat transfer enhancement has been measured in narrow, rectangular channels with various turbulators. The present experimental investigation has shown the turbulators, coupled with the rotation induced Coriolis and buoyancy forces, result in non-uniform levels of heat transfer enhancement in the cooling channels. Advanced turbulator configurations can be used to provide increased heat transfer enhancement. Although these designs result in increased frictional losses, the benefit of the heat transfer enhancement outweighs the frictional losses.
Author: Lesley Mae Wright Publisher: ISBN: Category : Languages : en Pages :
Book Description
The present work has been an experimental investigation to evaluate the applicability of gas turbine cooling technology. With the temperature of the mainstream gas entering the turbine elevated above the melting temperature of the metal components, these components must be cooled, so they can withstand prolonged exposure to the mainstream gas. Both external and internal cooling techniques have been studied as a means to increase the life of turbine components. Detailed film cooling effectiveness distributions have been obtained on the turbine blade platform with a variety of cooling configurations. Because the newly developed pressure sensitive paint (PSP) technique has proven to be the most suitable technique for measuring the film effectiveness, it was applied to a variety of platform seal configurations and discrete film flows. From the measurements it was shown advanced seals provide more uniform protection through the passage with less potential for ingestion of the hot mainstream gases into the engine cavity. In addition to protecting the outer surface of the turbine components, via film cooling, heat can also be removed from the components internally. Because the turbine blades are rotating within the engine, it is important to consider the effect of rotation on the heat transfer enhancement within the airfoil cooling channels. Through this experimental investigation, the heat transfer enhancement has been measured in narrow, rectangular channels with various turbulators. The present experimental investigation has shown the turbulators, coupled with the rotation induced Coriolis and buoyancy forces, result in non-uniform levels of heat transfer enhancement in the cooling channels. Advanced turbulator configurations can be used to provide increased heat transfer enhancement. Although these designs result in increased frictional losses, the benefit of the heat transfer enhancement outweighs the frictional losses.
Author: Zhihong Gao Publisher: ISBN: Category : Languages : en Pages :
Book Description
The hot gas temperature in gas turbine engines is far above the permissible metal temperatures. Advanced cooling technologies must be applied to cool the blades, so they can withstand the extreme conditions. Film cooling is widely used in modern high temperature and high pressure blades as an active cooling scheme. In this study, the film cooling effectiveness in different regions of gas turbine blades was investigated with various film hole/slot configurations and mainstream flow conditions. The study consisted of four parts: 1) effect of upstream wake on blade surface film cooling, 2) effect of upstream vortex on platform purge flow cooling, 3) influence of hole shape and angle on leading edge film cooling and 4) slot film cooling on trailing edge. Pressure sensitive paint (PSP) technique was used to get the conduction-free film cooling effectiveness distribution. For the blade surface film cooling, the effectiveness from axial shaped holes and compound angle shaped holes were examined. Results showed that the compound angle shaped holes offer better film effectiveness than the axial shaped holes. The upstream stationary wakes have detrimental effect on film effectiveness in certain wake rod phase positions. For platform purge flow cooling, the stator-rotor gap was simulated by a typical labyrinth-like seal. Delta wings were used to generate vortex and modeled the passage vortex generated by the upstream vanes. Results showed that the upstream vortex reduces the film cooling effectiveness on the platform. For the leading edge film cooling, two film cooling designs, each with four film cooling hole configurations, were investigated. Results showed that the shaped holes provide higher film cooling effectiveness than the cylindrical holes at higher average blowing ratios. In the same range of average blowing ratio, the radial angle holes produce better effectiveness than the compound angle holes. The seven-row design results in much higher effectiveness than the three-row design. For the trailing edge slot cooling, the effect of slot lip thickness on film effectiveness under the two mainstream conditions was investigated. Results showed thinner lips offer higher effectiveness. The film effectiveness on the slots reduces when the incoming mainstream boundary layer thickness decreases.
Author: Jungho Choi Publisher: ISBN: Category : Languages : en Pages :
Book Description
This experimental study contains two points; part 1 - turbine blade heat transfer under low Reynolds number flow conditions, and part 2 - trailing edge cooling and heat transfer. The effect of unsteady wake and free stream turbulence on heat transfer and pressure coefficients of a turbine blade was investigated in low Reynolds number flows. The experiments were performed on a five blade linear cascade in a low speed wind tunnel. A spoked wheel type wake generator and two different turbulence grids were employed to generate different levels of the Strouhal number and turbulence intensity, respectively. The cascade inlet Reynolds number based on blade chord length was varied from 15,700 to 105,000, and the Strouhal number was varied from 0 to 2.96 by changing the rotating wake passing frequency (rod speed) and cascade inlet velocity. A thin foil thermocouple instrumented blade was used to determine the surface heat transfer coefficient. A Liquid crystal technique based on hue value detection was used to measure the heat transfer coefficient on a trailing edge film cooling model and internal model of a gas turbine blade. It was also used to determine the film effectiveness on the trailing edge. For the internal model, Reynolds numbers based on the hydraulic diameter of the exit slot and exit velocity were 5,000, 10,000, 20,000, and 30,000 and corresponding coolant-to-mainstream velocity ratios were 0.3, 0.6, 1.2, and 1.8 for the external models, respectively. The experiments were performed at two different designs and each design has several different models such as staggered / inline exit, straight / tapered entrance, and smooth / rib entrance. The compressed air was used in coolant air. A circular turbulence grid was employed to upstream in the wind tunnel and square ribs were employed in the inlet chamber to generate turbulence intensity externally and internally, respectively.
Author: Ernst Rudolf Georg Eckert Publisher: ISBN: Category : Aerodynamics Languages : en Pages : 44
Book Description
Summary: Transpiration and film cooling promise to be effective methods of cooling gas-turbine blades; consequently, analytical and experimental investigations are being conducted to obtain a better understanding of these processes. This report serves as an introduction to these cooling methods, explains the physical processes, and surveys the information available for predicting blade temperatures and heat-transfer rates. In addition, the difficulties encountered in obtaining a uniform blade temperature are discussed, and the possibilities of correcting these difficulties are indicated. Air is the only coolant considered in the application of these cooling methods.
Author: Shiou-Jiuan Li Publisher: ISBN: Category : Languages : en Pages : 158
Book Description
High turbine inlet temperature becomes necessary for increasing thermal efficiency of modern gas turbines. To prevent failure of turbine components, advance cooling technologies have been applied to different portions of turbine blades. The detailed film cooling effectiveness distributions along a rotor blade has been studied under combined effects of upstream trailing edge unsteady wake with coolant ejection by the pressure sensitive paint (PSP). The experiment is conducted in a low speed wind tunnel with a five blade linear cascade and exit Reynolds number is 370,000. The density ratios for both blade and trailing edge coolant ejection range from 1.5 to 2.0. Blade blowing ratios are 0.5 and 1.0 on suction surface and 1.0 and 2.0 on pressure surface. Trailing edge jet blowing ratio and Strouhal number are 1.0 and 0.12, respectively. Results show the unsteady wake reduces overall effectiveness. However, the unsteady wake with trailing edge coolant ejection enhances overall effectiveness. Results also show that the overall effectiveness increases by using heavier coolant for ejection and blade film cooling. Leading edge film cooling has been investigated using PSP. There are two test models: seven and three-row of film holes for simulating vane and blade, respectively. Four film holes' configurations are used for both models: radial angle cylindrical holes, compound angle cylindrical holes, radial angle shaped holes, and compound angle shaped holes. Density ratios are 1.0 to 2.0 while blowing ratios are 0.5 to 1.5. Experiments were conducted in a low speed wind tunnel with Reynolds number 100,900. The turbulence intensity near test model is about 7%. The results show the shaped holes have overall higher effectiveness than cylindrical holes for both designs. As increasing density ratio, density effect on shaped holes becomes evident. Radial angle holes perform better than compound angle holes as increasing blowing and density ratios. Increasing density ratio generally increases overall effectiveness for all configurations and blowing ratios. One exception occurs for compound angle and radial angle shaped hole of three-row design at lower blowing ratio. Effectiveness along stagnation row reduces as increasing density ratio due to coolant jet with insufficient momentum caused by heavier density coolant, shaped hole, and stagnation row. The electronic version of this dissertation is accessible from http://hdl.handle.net/1969.1/148288
Author: Akhilesh P. Rallabandi Publisher: ISBN: Category : Languages : en Pages :
Book Description
Gas turbine engines are extensively used in the aviation and power generation industries. They are used as topping cycles in combined cycle power plants, or as stand alone power generation units. Gains in thermodynamic efficiency can be realized by increasing the turbine inlet temperatures. Since modern turbine inlet temperatures exceed the melting point of the constituent superalloys, it is necessary to provide an aggressive cooling system. Relatively cool air, ducted from the compressor of the engine is used to remove heat from the hot turbine blade. This air flows through passages in the hollow blade (internal cooling), and is also ejected onto the surface of the blade to form an insulating film (film cooling). Modern land-based gas turbine engines use high Reynolds number internal flow to cool their internal passages. The first part of this study focuses on experiments pertaining to passages with Reynolds numbers of up to 400,000. Common turbulator designs (45degree parallel sharp-edged and round-edged) ribs are studied. Older correlations are found to require corrections in order to be valid in the high Reynolds number parameter space. The effect of rotation on heat transfer in a typical three-pass serpentine channel is studied using a computational model with near-wall refinement. Results from this computational study indicate that the hub experiences abnormally high heat transfer under rotation. An experimental study is conducted at Buoyancy numbers similar to an actual engine on a wedge shaped model trailing edge, roughened with pin-fins and equipped with slot ejection. Results show an asymmetery between the leading and trailing surfaces due to rotation - a difference which is subdued due to the provision of pin-fins. Film cooling effectiveness is measured by the PSP mass transfer analogy technique in two different configurations: a flat plate and a typical high pressure turbine blade. Parameters studied include a step immediately upstream of a row of holes; the Strouhal number (quantifying rotor-stator interaction) and coolant to mainstream density ratio. Results show a deterioration in film cooling effectiveness with on increasing the Strouhal number. Using a coolant with a higher density results in higher film cooling effectiveness.
Author: Lesley Mae Wright
Author: Lesley Mae Wright
Author: Zhihong Gao
Author: Vernon L. Arne
Author: Jungho Choi
Author: Ernst Rudolf Georg Eckert
Author: Herman H. Ellerbrock (Jr.)
Author: Shiou-Jiuan Li
Author: Akhilesh P. Rallabandi
Author: James D. Heidmann
Author: Eugene F. Schum