Experimental and Computational Analysis of Evaporative Spray Cooling for Gas Turbine Exhaust Ejectors PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Experimental and Computational Analysis of Evaporative Spray Cooling for Gas Turbine Exhaust Ejectors PDF full book. Access full book title Experimental and Computational Analysis of Evaporative Spray Cooling for Gas Turbine Exhaust Ejectors by Nathon Begg. Download full books in PDF and EPUB format.
Author: Nathon Begg Publisher: ISBN: Category : Languages : en Pages : 346
Book Description
This research studied the effects of evaporative spray cooling on air-air ejector performance. Experimental data was collected for the purpose of validating computational simulations. This was done by modifying an existing air-air ejector to accommodate four spray flow nozzles which were used to atomize cooling water. The only parameter that was varied throughout the study was the mass flow rate of cooling water. One single phase (air) case and four spray flow cases where performed and analyzed. The purpose of the single phase experiment was to have a baseline for the air-air ejector performance and isolate the sources of experimental error contributed by spray flow. Three specialized multiphase flow instruments were designed and fabricated by the author to measure, gas phase temperatures, spray mass flow rates, and mixture total pressures. A computational study was performed using the collected experimental data for inlet continuous phase and spray mass flow as boundary conditions for equivalent simulations. A temperature gradient modified turbulence model was written by the author to better predict the mixing rates found experimentally which was used for the duration of this research. Secondary droplet breakup was modeled by the author using empirical correlations following preliminary simulations recognizing the deficiencies of commercially available breakup models. Comparison of experimental and computational cases produced mixed results. It was found that the experimental gas temperature instrument performed poorly for the local droplet fluxes encountered during testing. The spray sampling probe showed more promising results with two integrated mass flows agreeing within 6% of computational simulations. The total pressure probe solved the issue of pressure port clogging, but measurements were representative of mixture density which made an inferred velocity calculation difficult. It was found that evaporation of spray flow before the nozzle exit plane caused a reduction in dynamic pressure and a reduction in back pressure. A full scale simulation was performed to determine the effects of scaling on evaporative spray cooling performance. It was found that for the geometrically similar full scale model, the total droplet surface area and particle residence times scaled up with the model which increased cooling performance.
Author: Nathon Begg Publisher: ISBN: Category : Languages : en Pages : 346
Book Description
This research studied the effects of evaporative spray cooling on air-air ejector performance. Experimental data was collected for the purpose of validating computational simulations. This was done by modifying an existing air-air ejector to accommodate four spray flow nozzles which were used to atomize cooling water. The only parameter that was varied throughout the study was the mass flow rate of cooling water. One single phase (air) case and four spray flow cases where performed and analyzed. The purpose of the single phase experiment was to have a baseline for the air-air ejector performance and isolate the sources of experimental error contributed by spray flow. Three specialized multiphase flow instruments were designed and fabricated by the author to measure, gas phase temperatures, spray mass flow rates, and mixture total pressures. A computational study was performed using the collected experimental data for inlet continuous phase and spray mass flow as boundary conditions for equivalent simulations. A temperature gradient modified turbulence model was written by the author to better predict the mixing rates found experimentally which was used for the duration of this research. Secondary droplet breakup was modeled by the author using empirical correlations following preliminary simulations recognizing the deficiencies of commercially available breakup models. Comparison of experimental and computational cases produced mixed results. It was found that the experimental gas temperature instrument performed poorly for the local droplet fluxes encountered during testing. The spray sampling probe showed more promising results with two integrated mass flows agreeing within 6% of computational simulations. The total pressure probe solved the issue of pressure port clogging, but measurements were representative of mixture density which made an inferred velocity calculation difficult. It was found that evaporation of spray flow before the nozzle exit plane caused a reduction in dynamic pressure and a reduction in back pressure. A full scale simulation was performed to determine the effects of scaling on evaporative spray cooling performance. It was found that for the geometrically similar full scale model, the total droplet surface area and particle residence times scaled up with the model which increased cooling performance.
Author: Grant Armitage Publisher: ISBN: Category : Languages : en Pages : 292
Book Description
The research performed in this work investigated evaporative spray cooling systems using water near a 45 degree bends in gas turbine exhaust piping systems. Both experimental data and numerical data were generated with the goal of evaluating the ability of Fluent 6.3.26 to predict the performance of these systems for the purpose of design using only modest computational resources. Three cases were investigated in this research: single phase exhaust flow with no water injection, injecting water before the bend and injecting water after the bend. Various probes were used to measure dry bulb temperature, total pressure and water mass flux of the two phase flow at the exit of the pipe. Seven hole probes and pitot static probes were used to measure single phase flow properties. Numerical simulations were performed using mass flow boundary conditions which were generated from experimental results. A turbulence model was selected for the simulations based on comparisons of single phase simulations with experimental data and convergence ability. Using Fluent's discrete phase model, different wall boundary conditions for the discrete phase were used in order to find the model which would best match the evaporation rates of the experimental data. Mass flux values through the exit plane of the pipe were found to be the most reliable of all the two phase data collected. Results from numerical simulations revealed the shortcomings of the available discrete phase wall boundary conditions to accurately predict the interaction of the liquid phase with the wall. Experimental results for both cases showed extensive areas of the wall which had liquid film layers running down the length of the pipe. Simulations resulted in particles either failing to impact the wall and create a liquid film, or creating a liquid film which was much smaller than the film present in experimental results. This led to 8% and 15% discrepancy in evaporation amounts between numerical and experimental results for water injection upstream and downstream of the bend respectively. Under-prediction of areas wetted with a wall film in the simulations also led to gross over predictions of wall temperature in numerical results.
Author: Thomas Earl Dyson Publisher: ISBN: Category : Languages : en Pages : 576
Book Description
This study focused on the improvement of film cooling for gas turbine vanes using both computational and experimental techniques. The experimental component used a matched Biot number model to measure scaled surface temperature (overall effectiveness) distributions representative of engine conditions for two new configurations. One configuration consisted of a single row of holes on the pressure surface while the other used numerous film cooling holes over the entire vane including a showerhead. Both configurations used internal impingement cooling representative of a 1st vane. Adiabatic effectiveness was also measured. No previous studies had shown the effect of injection on the mean and fluctuating velocity profiles for the suction surface, so measurements were made at two locations immediately upstream of film cooling holes from the fully cooled cooling configuration. Different blowing conditions were evaluated. Computational tools are increasingly important in the design of advanced gas turbine engines and validation of these tools is required prior to integration into the design process. Two film cooling configurations were simulated and compared to past experimental work. Data from matched Biot number experiments was used to validate the overall effectiveness from conjugate simulations in addition to adiabatic effectiveness. A simulation of a single row of cooling holes on the suction side also gave additional insight into the interaction of film cooling jets with the thermal boundary layer. A showerhead configuration was also simulated. The final portion of this study sought to evaluate the performance of six RANS models (standard, realizable, and renormalization group k-[epsilon]; standard k-[omega]; k-[omega] SST; and Transition SST) with respect to the prediction of thermal boundary layers. The turbulent Prandtl number was varied to test a simple method for improvement of the thermal boundary layer predictions.
Author: Publisher: ISBN: Category : Languages : en Pages : 31
Book Description
The thermal efficiency of gas turbine systems depends largely on the turbine inlet temperature. Recent decades have seen a steady rise in the inlet temperature and a resulting reduction in fuel consumption. At the same time, it has been necessary to employ intensive cooling of the hot components. Among various cooling methods, film cooling has become a standard method for cooling of the turbine airfoils and combustion chamber walls. The University of Minnesota program is a combined experimental and computational study of various film-cooling configurations. Whereas a large number of parameters influence film cooling processes, this research focuses on compound angle injection through a single row and through two rows of holes. Later work will investigate the values of contoured hole designs. An appreciation of the advantages of compound angle injection has risen recently with the demand for more effective cooling and with improved understanding of the flow; this project should continue to further this understanding. Approaches being applied include: (1) a new measurement system that extends the mass/heat transfer analogy to obtain both local film cooling and local mass (heat) transfer results in a single system, (2) direct measurement of three-dimensional turbulent transport in a highly-disturbed flow, (3) the use of compound angle and shaped holes to optimize film cooling performance, and (4) an exploration of anisotropy corrections to turbulence modeling of film cooling jets.
Author: Nathon Begg
Author: Nathon Begg
Author: Grant Armitage
Author: Grant Armitage
Author: Roy A. McKinnon
Author: C.F.E. Regnier
Author: R.E. Marquardt
Author: Thomas Earl Dyson
Author: Marion John Balcerzak
Author: 
Author: