Evaluation of Reynolds Number and Tunnel Wall Porosity Effects on Nozzle Afterbody Drag at Transonic Mach Numbers PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Evaluation of Reynolds Number and Tunnel Wall Porosity Effects on Nozzle Afterbody Drag at Transonic Mach Numbers PDF full book. Access full book title Evaluation of Reynolds Number and Tunnel Wall Porosity Effects on Nozzle Afterbody Drag at Transonic Mach Numbers by C. E. Robinson. Download full books in PDF and EPUB format.
Author: C. E. Robinson Publisher: ISBN: Category : Aerodynamics, Transonic Languages : en Pages : 38
Book Description
An experimental investigation was conducted to study the effects of Reynolds number variation on isolated nozzle afterbody performance. A strut-mounted cone-cylinder model with three separate afterbody configurations for Aerospace Research and Development (AGARD) was used for this investigation. This program was conducted in two phases distinguished by the model size and the wind tunnels used to obtain the experimental results. The effect of tunnel wall porosity on nozzle afterbody (NAB) performance was investigated.
Author: C. E. Robinson Publisher: ISBN: Category : Aerodynamics, Transonic Languages : en Pages : 38
Book Description
An experimental investigation was conducted to study the effects of Reynolds number variation on isolated nozzle afterbody performance. A strut-mounted cone-cylinder model with three separate afterbody configurations for Aerospace Research and Development (AGARD) was used for this investigation. This program was conducted in two phases distinguished by the model size and the wind tunnels used to obtain the experimental results. The effect of tunnel wall porosity on nozzle afterbody (NAB) performance was investigated.
Author: L. L. Galigher Publisher: ISBN: Category : Aerodynamics, Transonic Languages : en Pages : 144
Book Description
An experimental program was conducted to investigate the interaction effects which occur between the nozzle exhaust flow and the external flow field associated with isolated nozzle afterbody configurations at transonic Mach numbers. Pressure data were obtained from three afterbody geometries with boattail angles of 10, 15, and 25 deg at Mach numbers from 0.6 to 1.5 at zero angles of attack and sideslip. Cold (High-pressure air) and hot (Air/ethylene combustion) jet test techniques were used to simulate and duplicate, respectively, the nozzle exhaust flow for a sonic jet installation. Nozzle exhaust temperature was varied from 540 to approximately 2,900 R. The most significant results pertain to those effects on boattail pressure drag caused by exhaust plume temperature and flow asymmetry (Model support strut induced). The differences obtained in boattail pressure drag between the cold jet simulation and hot jet duplication results were significant at nozzle pressure ratios representative for turbofan and turbojet engines at subsonic Mach numbers. Adjusting the cold jet nozzle pressure ratio to correct for changes in the exhaust plume specific heat ratio with temperature did not account for the differences observed. Flow asymmetry effects were Mach number and nozzle pressure ratio dependent and increased in severity as the boattail angle was increased.
Author: James L. Jacocks Publisher: ISBN: Category : Airplanes Languages : en Pages : 36
Book Description
The development of a computer program for solving the compressible, axisymmetric, mass-averaged Navier-Stokes equations is described. The basic numerical algorithm is the MacCormack explicit predictor-corrector scheme. Turbulence modeling is accomplished using an algebraic, two-layer eddy viscosity model with a novel modification dependent on the streamwise gradient of vorticity. Comparisons of computed results with experimental data are presented for several nozzle-afterbody configurations with either or simulated plumes. (Author).
Author: North Atlantic Treaty Organization. Advisory Group for Aerospace Research and Development. Propulsion and Energetics Panel Publisher: ISBN: Category : Aerodynamics, Transonic Languages : en Pages : 404
Author: F. M. Jackson Publisher: ISBN: Category : Aerodynamics, Transonic Languages : en Pages : 104
Book Description
Tests were conducted in the AEDC Propulsion Wind Tunnel (16T) to determine the tunnel test section Mach number distributions and calibration at various Reynolds numbers. The calibration was conducted at Mach numbers from 0.2 to 1.6 and at Reynolds numbers from 400,000/ft to 6,400,000/ft. The calibration was conducted using the propulsion test section (Test Section 1) and centerline pipe and wall pressure orifices to define the Mach number distributions. A quantitative evaluation of the effects of tunnel pressure ratio, test section wall angle, and Reynolds number on the centerline Mach number distributions was determined by analysis of the local Mach number deviations. The results indicate that Mach number distributions of good quality are obtained for both zero and the optimum wall angle schedule. For complete generality, the Tunnel 16T calibration must be defined as a function of test section wall angle, Reynolds number, and Mach number.
Author: C. E. Robinson
Author: C. E. Robinson
Author: 
Author: L. L. Galigher
Author: James L. Jacocks
Author: 
Author: 
Author: 
Author: North Atlantic Treaty Organization. Advisory Group for Aerospace Research and Development. Propulsion and Energetics Panel
Author: 
Author: F. M. Jackson