Author: C. K. ChowPublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
Effect of thickness on the fracture toughness of irradiated zr-2.5nb pressure tubes
Author: C. K. ChowSize, geometry and material effects in fracture toughness testing of irradiated zr-2.5nb pressure tube material
Author: P. H. DaviesRadial fracture toughness of irradiated zr-2.5nb pressure tube material
Author: D. D. HimbeaultCorrelation Between Irradiated and Unirradiated Fracture Toughness of Zr-2.5Nb Pressure Tubes
Author: CK. ChowPublisher:
ISBN:
Category : Crack growth resistance
Languages : en
Pages : 33
Book Description
Three coordinated research programs were undertaken on the fracture toughness of Zr-2.5Nb pressure tubes to determine relationships between irradiated and unirradiated values, the effect of long-term irradiation, and the causes of the variation in toughness. The present paper describes results from these programs and their implications.
Effect of Irradiation on the Fracture Properties of Zr-2.5Nb Pressure Tubes at the End of Design Life
Author: S. St LawrencePublisher:
ISBN:
Category : Delayed hydride cracking
Languages : en
Pages : 24
Book Description
To determine the fracture properties of Zr-2.5Nb pressure tubes irradiated until the end of design life, cantilever beam, curved compact toughness, and transverse tensile samples were prepared from a typical pressure tube and irradiated in the high flux reactor OSIRIS at CEA, Saclay, France. Experiments were conducted on two batches of samples mounted in two irradiation inserts. Each insert held sixteen samples of each type of specimen. The first insert was irradiated to a fluence corresponding to approximately half of the design life in a CANDU3 reactor. The experimental results were reported in [1]. Samples in the second insert were irradiated for 10.5 years in OSIRIS and received a maximum neutron fluence of 2.61 x 1026 n/m2 (E > 1 MeV), being equivalent to 2.98 x 1026 n/m2 (E > 1 MeV) in a CANDU reactor, i.e., corresponding to ~30 years operation in CANDU reactors at 80 % capacity factor. The present report describes the results of tensile, fracture toughness, and Delayed Hydride Cracking (DHC) tests and XRD microstructure analysis from the second batch of specimens. A continuous and gradual evolution in tensile, fracture, DHC properties, and dislocation densities is demonstrated without any evidence of a sudden change following the initial transitient at very low fluence. In the whole high fluence range, there is a very slow rate of increase in c-component dislocation density, strength, and DHC velocity and a slow reduction in elongation and Nb concentration in the ?-phase. The a-type dislocation density and fracture toughness remain approximately constant. The results from the second insert of specimens confirm that, following the initial transient at very low fluence, there is little further change in the fracture properties of Zr-2.5Nb pressure tube material. Therefore, material properties behave in a stable and predicable manner to the end of a 30 years design life for CANDU reactor pressure tubes.
Effect of Long-Term Irradiation on the Fracture Properties of Zr-2.5Nb Pressure Tubes
Author: S. SagatPublisher:
ISBN:
Category : Fracture
Languages : en
Pages : 17
Book Description
Results from fracture toughness and tensile and delayed hydride cracking (DHC) tests on Zr-2.5Nb pressure tubes removed from CANDU power reactors in the 1970s and 80s for surveillance showed considerable scatter. At that time, the cause of the scatter was unknown and prediction of fracture toughness to the end of the design life of a CANDU reactor using the surveillance data was difficult. To eliminate the heat-to-heat variability and to determine end-of-life mechanical properties, a program was undertaken to irradiate, in a high-flux reactor, fracture toughness, DHC, and transverse tensile specimens from a single "typical" pressure tube. Two inserts were placed in the OSIRIS reactor at CEA, Saclay, in 1988. Each insert held 16 of each type of specimen. The first insert, ERABLE 1, was designed so that half the specimens could be replaced at intervals and the properties could be measured as a function of fluence. All the specimens would be removed after a total fluence of 15 x 1025 n . m-2, E > 1 MeV. The second insert, ERABLE 2, was designed to run without interruption to a fluence of 30 x 1025 n . m-2, the fluence corresponding to 30 years' operation of a CANDU reactor at 90% capacity factor. The irradiation temperature was chosen to be 250°C, the inlet temperature of early CANDU reactors. The irradiation of ERABLE 1 has been completed and sets of specimens have been removed and tested with maximum fluences of approximately 0.7, 1.7, 2.8, 12, and 17 x 1025 n . m-2, E > 1 MeV. X-ray and TEM examinations have been performed on the material from fractured specimens to characterize the irradiation damage. Results showed that there is, initially, a large change in the mechanical properties before a fluence of 0.6 x 1025 n . m-2, E > 1 MeV (corresponding to an initial rapid increase in a-type dislocation density), followed by a gradual change. As expected, the fracture toughness decreased with fluence, whereas the yield strength, UTS, and DHC crack velocities all increased. Z-ray analysis showed that, although the a-type dislocation density remained constant after the initial increase, the number of c-component dislocations showed a steady increase, agreeing with the behavior seen in the mechanical specimens. Because the flux in OSIRIS is different from that in a CANDU reactor, specimens were also irradiated in NRU, a heavy water moderated test reactor with approximately the same flux as a CANDU reactor, to fluences of 0.3, 0.6, and 1.0 x 1025 n.m-2, E > 1 MeV for comparison. These initial results show that, once past the initial transient, one can have confidence that there will be little further degradation with fluence, with the results from the NRU specimens being similar to those from OSIRIS.
Fracture toughness study of irradiated zr-2.5nb pressure tube f316
Author: P. H. DaviesFracture Toughness of Irradiated Zr-2.5Nb Pressure Tubes from CANDU Reactors
Author: R. ChoubeyPublisher:
ISBN:
Category : Charpy
Languages : en
Pages : 30
Book Description
About 400 pressure-tubes made of cold-worked Zr-2.5Nb are used in a CANDU power reactor to contain the nuclear fuel and the heat transport fluid, heavy water, at between 250 to 310°C at a pressure of about 10 MPa. The fracture toughness of these tubes is needed to determine if they are fit for service. We have measured the fracture toughness by bursting 450 mm long tube sections and using 17 mm curved compact toughness (C(T)) specimens, employing the J-integral resistance curve method in both cases. The burst test is expensive but it simulates the stress state under which the pressure tubes operate, while the small specimen method is more economical although the interpretation of data is more difficult.
Author: D. D. Himbeault
Author: C. K. Chow