Effect of Chord Size on Weight and Cooling Characteristics of Air-cooled Turbine Blades PDF Download

Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Effect of Chord Size on Weight and Cooling Characteristics of Air-cooled Turbine Blades PDF full book. Access full book title Effect of Chord Size on Weight and Cooling Characteristics of Air-cooled Turbine Blades by Jack B. Esgar. Download full books in PDF and EPUB format.

Effect of Chord Size on Weight and Cooling Characteristics of Air-cooled Turbine Blades

Effect of Chord Size on Weight and Cooling Characteristics of Air-cooled Turbine Blades PDF Author: Jack B. Esgar
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 44

Book Description
An analysis has been made to determine the effect of chord size on the weight and cooling characteristics of shell-supported, air-cooled gas-turbine blades. In uncooled turbines with solid blades, the general practice has been to design turbines with high aspect ratio (small blade chord) to achieve substantial turbine weight reduction. With air-cooled blades, this study shows that turbine blade weight is affected to a much smaller degree by the size of the blade chord.

Effect of Chord Size on Weight and Cooling Characteristics of Air-cooled Turbine Blades

Effect of Chord Size on Weight and Cooling Characteristics of Air-cooled Turbine Blades PDF Author: Jack B. Esgar
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 44

Book Description
An analysis has been made to determine the effect of chord size on the weight and cooling characteristics of shell-supported, air-cooled gas-turbine blades. In uncooled turbines with solid blades, the general practice has been to design turbines with high aspect ratio (small blade chord) to achieve substantial turbine weight reduction. With air-cooled blades, this study shows that turbine blade weight is affected to a much smaller degree by the size of the blade chord.

Technical Note - National Advisory Committee for Aeronautics

Technical Note - National Advisory Committee for Aeronautics PDF Author: United States. National Advisory Committee for Aeronautics
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 1014

Book Description


Index of NACA Technical Publications

Index of NACA Technical Publications PDF Author: United States. National Advisory Committee for Aeronautics
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 388

Book Description


A Selected Listing of NASA Scientific and Technical Reports for ...

A Selected Listing of NASA Scientific and Technical Reports for ... PDF Author:
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 818

Book Description


An Experimental Investigation of Sting-support Effects on Drag and a Comparison with Jet Effects at Transonic Speeds

An Experimental Investigation of Sting-support Effects on Drag and a Comparison with Jet Effects at Transonic Speeds PDF Author: Charles L. Shuford
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 178

Book Description


Reports and Documents

Reports and Documents PDF Author: United States. Congress
Publisher:
ISBN:
Category :
Languages : en
Pages : 1564

Book Description


Effect of Propeller Location and Flap Deflection on the Aerodynamic Characteristics of a Wing-propeller Combination for Angles of Attack from 0 to 80 Degrees

Effect of Propeller Location and Flap Deflection on the Aerodynamic Characteristics of a Wing-propeller Combination for Angles of Attack from 0 to 80 Degrees PDF Author: William A. Newsom
Publisher:
ISBN:
Category : Airplanes
Languages : en
Pages : 714

Book Description
An investigation has been made to determine the effect of propeller location and flap deflection on the lift, drag, and pitching-moment characteristics of a wing-propeller combination over an angle-of-attack range from 0 to 80 degrees. The model had four propellers, the slipstream from which covered practically the entire span of the wing. The wing had a 30-percent-chord slotted flap and an 8.5-percent-chord slat. Data were obtained for flap deflections of 0, 20, 40, and 60 degrees with the slat off and on. For one propeller position the power input to the model was measured and tuft studies of the flow on the wing were made. The data are analyzed to assess the feasibility, from consideration of stability and control, of a tilting-wing vertical-take-off-and-landing airplane with the wing pivoted behind the primary wing structure to provide a desirable structural configuration. The main object of the investigation was to determine whether advantage might be taken of the forward shift of the center of gravity of the airplane, as the wing is tilted from an angle of attack of 90 to 0 degrees, to minimize the change in trim pitching moment throughout the transition speed range for such a configuration. The results indicate that with proper propeller position and programming of flap deflection, it is possible to design a configuration of this type in which essentially no change in trim is required throughout the transition from hovering to normal unstalled forward flight.

Semiannual Report to the Congress

Semiannual Report to the Congress PDF Author: United States. National Aeronautics and Space Administration
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 302

Book Description


Preliminary Survey of Possible Cooling Methods for Hypersonic Aircraft

Preliminary Survey of Possible Cooling Methods for Hypersonic Aircraft PDF Author: Jack B. Esgar
Publisher:
ISBN:
Category : Aerodynamics
Languages : en
Pages : 44

Book Description
Abstract: Many methods of cooling the structure of an aircraft capable of flight speeds up to 18,000 feet per second were studied. Water and hydrogen stored in the liquid state appear very promising as both coolants and heat sinks. The storage and circulation of hydrogen throughout the aircraft need not be a hazard. Cooling the outer skin of the aircraft in high-equilibrium-temperature regions could probably be avoided by using a material such as silicon carbide. The internal structure could be cooled by use of a thin layer of balsa wood saturated with water. In this way tanks for storage of coolant would be avoided.

Report

Report PDF Author:
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 1180

Book Description