Author: Robert B. Burditt
Publisher:
ISBN:
Category : Annealing of metals
Languages : en
Pages : 24
Book Description
Effect of Annealing Time and Working on Indicated Thickness of Uranium
Author: Robert B. Burditt
Publisher:
ISBN:
Category : Annealing of metals
Languages : en
Pages : 24
Book Description
Publisher:
ISBN:
Category : Annealing of metals
Languages : en
Pages : 24
Book Description
U.S. Government Research Reports
Recrystallization of Heavily Cold-rolled Uranium Sheet
Author: W. R. Yario
Publisher:
ISBN:
Category : Annealing of metals
Languages : en
Pages : 46
Book Description
Changes in mean expansion coefficients upon annealing uranium sheet that had been rolled to 80% reduction in thickness at room temperature indicated that three different preferred orientations could be developed upon recrystallization. One preferred orientation, which is essentially the same as that of the as-rolled material, resulted from annealing for long times at 360 deg C or at a lower temperature; a second type was created by annealing for moderate times between 400 and 600 deg C; and the third accompanied grain coarsening at 650 deg C. The microstructures of the as-rolled and annealed specimens were extremely heterogeneous because of the large grain size present prior to final fabrication at room temperature. The as-rolled structures consisted of heavily deformed areas and smaller quantities of lightly deformed material. The annealing of the former was characterized by initial creation of very fine recrystallized grains which were absorbed later by discontinuous growth of larger grains. Lightly deformed areas, upon annealing, first exhibited recovery by polygonization and then underwent normal recrystallization.
Publisher:
ISBN:
Category : Annealing of metals
Languages : en
Pages : 46
Book Description
Changes in mean expansion coefficients upon annealing uranium sheet that had been rolled to 80% reduction in thickness at room temperature indicated that three different preferred orientations could be developed upon recrystallization. One preferred orientation, which is essentially the same as that of the as-rolled material, resulted from annealing for long times at 360 deg C or at a lower temperature; a second type was created by annealing for moderate times between 400 and 600 deg C; and the third accompanied grain coarsening at 650 deg C. The microstructures of the as-rolled and annealed specimens were extremely heterogeneous because of the large grain size present prior to final fabrication at room temperature. The as-rolled structures consisted of heavily deformed areas and smaller quantities of lightly deformed material. The annealing of the former was characterized by initial creation of very fine recrystallized grains which were absorbed later by discontinuous growth of larger grains. Lightly deformed areas, upon annealing, first exhibited recovery by polygonization and then underwent normal recrystallization.
Nuclear Science Abstracts
Preferred Orientation of Cold-rolled and Recrystallized Uranium Plate
Author: William R. McDonell
Publisher:
ISBN:
Category : Recrystallization (Metallurgy)
Languages : en
Pages : 24
Book Description
Publisher:
ISBN:
Category : Recrystallization (Metallurgy)
Languages : en
Pages : 24
Book Description
Annealing Effects in Thorium-uranium Alloys
Author: Gordon G. Bentle
Publisher:
ISBN:
Category : Annealing of metals
Languages : en
Pages : 24
Book Description
Publisher:
ISBN:
Category : Annealing of metals
Languages : en
Pages : 24
Book Description
Review of Metal Literature
Author: American Society for Metals
Publisher:
ISBN:
Category : Metal-work
Languages : en
Pages : 1440
Book Description
An annotated survey of articles and technical papers appearing in the engineering, scientific and industrial journals and books here and abroad.
Publisher:
ISBN:
Category : Metal-work
Languages : en
Pages : 1440
Book Description
An annotated survey of articles and technical papers appearing in the engineering, scientific and industrial journals and books here and abroad.
Effects of Rolling and Heat Treatment on Anisotropic Irradiation Growth of Uranium
Author: J. H. Kittel
Publisher:
ISBN:
Category : Irradiation
Languages : en
Pages : 38
Book Description
An investigation was made to determine the effect of rolling temperature, roll pass design, amount of reduction, and heat treatment before and after rolling on the anisotropic growth rate of uranium under irradiation. The growth rate was found to increase with decreasing rolling temperature and with increasing reduction of area at 300 deg C. The rate of elongation was proportional to the amount of (010) component present or, where shortening occurred, to the amount of (100) component. Oval-edge-oval roll passes resulted in somewhat higher irradiation growth rates than did round roll passes. Recrystallization after rolling effectively reduced the irradiation growth rate of uranium rolled at temperatures of 500 deg C and lower. Irradiation caused length shortening in uranium which was beta quenched after being round-rolled at temperatures of 400 deg C and above, and which was beta quenched after being oval- rolled at temperatures of 300 deg C and above.
Publisher:
ISBN:
Category : Irradiation
Languages : en
Pages : 38
Book Description
An investigation was made to determine the effect of rolling temperature, roll pass design, amount of reduction, and heat treatment before and after rolling on the anisotropic growth rate of uranium under irradiation. The growth rate was found to increase with decreasing rolling temperature and with increasing reduction of area at 300 deg C. The rate of elongation was proportional to the amount of (010) component present or, where shortening occurred, to the amount of (100) component. Oval-edge-oval roll passes resulted in somewhat higher irradiation growth rates than did round roll passes. Recrystallization after rolling effectively reduced the irradiation growth rate of uranium rolled at temperatures of 500 deg C and lower. Irradiation caused length shortening in uranium which was beta quenched after being round-rolled at temperatures of 400 deg C and above, and which was beta quenched after being oval- rolled at temperatures of 300 deg C and above.
Rolling of Uranium
Author:
Publisher:
ISBN:
Category : Rolling (Metal-work)
Languages : en
Pages : 222
Book Description
Publisher:
ISBN:
Category : Rolling (Metal-work)
Languages : en
Pages : 222
Book Description