Author: B. RebbechiPublisher:
ISBN: 9781555896072
Category :
Languages : en
Pages : 11
Book Description
Dynamic Measurements of Gear Tooth Friction and Load
Author: B. RebbechiPublisher:
ISBN: 9781555896072
Category :
Languages : en
Pages : 11
Book Description
Measurement of Gear Tooth Dynamic Friction
Author: Brian RebbechiDynamic Loads on Gear Teeth
Author: American Society of Mechanical Engineers. Special research committee on the strength of gear teethPublisher:
ISBN:
Category : Gearing
Languages : en
Pages : 82
Book Description
A Study of Dynamic Loads on Straight Spur Gear Teeth
Author: Paul Jay UmbergerPublisher:
ISBN:
Category :
Languages : en
Pages : 74
Book Description
The dynamic loads acting on gear teeth are very complex. To better understand dynamic loads, this research was carried out with the objectives of measuring experimentally dynamic loads and the frictional forces between gear teeth in mesh. By using strain gages mounted on the sides of the teeth, the transverse component of the dynamic load was measured and is shown for all phases of contact. Using the transverse component at the pitch radius, the dynamic load ratios were computed and found to be substantially lower than predicted by the Buckingham equation. However, sufficient information for evaluating the frictional force was not obtained and further research will be required to evaluate the radial component of the dynamic load. (Author).
Scientific and Technical Aerospace Reports
Author: Dynamic Forces in Spur Gears - Measurement, Prediction, and Code Validation
Author: The Art of Gear Fabrication
Author: Prem H. DaryaniPublisher: Industrial Press Inc.
ISBN: 9780831131425
Category : Technology & Engineering
Languages : en
Pages : 224
Book Description
Provides beginners with sufficient information to independently process six typical gears step by step. Presents model numbers, capacity and addresses of gear machinery manufacturers and suppliers at the end of each process description. Offers gear designers practical and useful hints on reducing fabricating costs. Contains useful tables from commercial catalogs, including cross-references of different U.S. standards and American stainless steel materials with equivalent German, British, French and Italian materials. Discusses heat treatment in an easy-to-understand manner.
Analytical Mechanics of Gears
Author: Earle BuckinghamPublisher: Courier Corporation
ISBN: 0486657124
Category : Technology & Engineering
Languages : en
Pages : 578
Book Description
This volume provides a solid foundation for logical gear design practices and data. Topics include an analysis of conjugate gear-tooth action, nature of the contact, and resulting gear-tooth profiles of several types of gears, plus gear teeth in action. Indispensable guide for engineers concerned with tooth geometry, manufacturing accuracies, and general design. 1949 edition.
The Construction and Use of a Test Machine to Measure Dynamic Loads on Gear Teeth
Author: John Alvin Pethick (II.)Publisher:
ISBN:
Category :
Languages : en
Pages : 86
Book Description
The action of mating gear teeth is a very complex thing. Very little is known of the forces that act on gears as they mesh. It is with this in mind that a testing machine was designed, built, and used to investigate the feasibility of obtaining gear tooth load information, by the use of strain gages mounted on the teeth of a test gear. The construction and operation of the testing machine is descirbed, followed by the results of experiments conducted. The application of the experimental results to some design considerations in gears is then discussed. A great need exists for gear loading information, and gear testing machine has proved to be successful in the initial phases of its operation. (Author).
The Construction and Use of a Test Machine to Measure Dynamic Loads on Gear Teeth
Author: John Alvin PethickPublisher:
ISBN:
Category :
Languages : en
Pages : 86
Book Description
The action of mating gear teeth is a very complex thing. Very little is known of the forces that act on gears as they mesh. It is with this in mind that a testing machine was designed, built and used to investigate the feasability of obtaining gear tooth load information, by the use of strain gages mounted on the teeth of a test gear. The construction and operation of the testing machine is described, followed by the results of experiments conducted. The application of the experimental results to some design considerations in gears is then discussed. A great need exists for gear loading information, and the gear testing machine has proved to be successful in the initial phases of its operation.