Control of Horizontal Cracking in the Ends of Pretensioned Prestressed Concrete Girders PDF Download

Author: W.T. Marshall
Publisher:
ISBN:
Category :
Languages : en
Pages : 19

View

Book Description

Author: William Thomas Marshall
Publisher:
ISBN:
Category : Prestressed concrete beams
Languages : en
Pages : 19

View

Book Description

Author: Maher K. Tadros
Publisher: Transportation Research Board
ISBN: 0309118352
Category : Technology & Engineering
Languages : en
Pages : 76

View

Book Description
This report establishes a user's manual for the acceptance, repair, or rejection of precast/prestressed concrete girders with longitudinal web cracking. The report also proposes revisions to the AASHTO LRFD Bridge Design Specifications and provides recommendations to develop improved crack control reinforcement details for use in new girders. The material in this report will be of immediate interest to bridge engineers.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

View

Book Description
Hundreds of prestressed concrete girders are used each year for building bridges. Prestressed concrete girders are preferred due to their effective span to depth ratios, and higher durability characteristics. The prestress transfer from the prestressing strands to concrete takes place at the girder ends. Characteristic cracks form in this end region during or immediately after detensioning. These cracks are more severe for the heavily prestressed deep bulb tee girders with thin webs, creating durability concerns. The problem can be structurally hazardous if cracks form paths for corrosion agents to reach the steel strands. Cracks in the bottom flange closer to the strands can easily form such paths. This research primarily focused on the analyses of nonlinear prestressed girder end regions to understand and recommend control methods for girder end cracking. The behavior of the pretensioned girder ends was simulated using nonlinear finite element analysis. The accuracy of the models was ensured by including the concrete nonlinearity, strain softening and stress redistribution upon cracking. The finite element modeling techniques were verified by test data. The principal tensile strain patterns correlating with cracking were used to explain the reasons behind each type of crack. Potential solutions to control end cracking were examined via finite element models. The impact of end zone reinforcement pattern, debonding of strands, strand cutting order, draped strand pattern, and lifting of the girder on the cracks were evaluated. The reduction in principal tensile strains associated with cracking was quantified for each crack control method. The analysis results showed that debonding strands can effectively control cracking. Other methods improve the end zone strains however are not sufficient to eliminate cracking alone. Combining the solutions involving debonding, extra reinforcing in the web, and a controlled sequence of strand detensioning should lead to elimination of end cracking.

Author: Emre Kizilarslan
Publisher:
ISBN:
Category :
Languages : en
Pages : 202

View

Book Description
Wisconsin bulb tee pretensioned concrete girders have being used for bridges. Their effective spans to depth ratios and higher durability have made prestressed concrete girders desirable. However, cracks were observed at the anchorage zones of these girders because of the demand. To satisfy demand, these girders are heavily prestressed. Cracks initiate during detensioning of pretensioned strands and grow more while transporting them to the resting beds. These cracks create durability concerns as cracks lead aggressive salty water to the steel strands, endangering structures' stability. Especially, cracks in the bottom flange closer to the strands are main concerns in this research. This research primarily focused on the analyses of prestressed girder ends with modelling with nonlinear material properties to understand and recommend control methods for girder end cracking. The end zone behavior of the pretensioned girder was modelled using nonlinear material properties. The concrete nonlinearity, strain softening and stress redistribution upon cracking were also included in the behavior and the verification of tests were done by real tests on these girders. Finally, the reasons for cracks were explained by examining the principal tensile strain directions. The results of previous study showed that debonding strands can effectively control cracking. In this thesis, only debonding for cracking control method, therefore, was tested on 72W with 48 strands and 54W with 42 strands WI girders to see the real effect of debonding on anchorage zone cracks. After getting good results from tests and verifying them with Finite Element Analysis models, exact debonding percentages for other girders to eliminate cracks were presented by giving results of FEA models built for each of them.

Author: Rafik Y. Itani
Publisher:
ISBN:
Category : Concrete beams
Languages : en
Pages : 140

View

Book Description

Author: Michael G. Oliva
Publisher:
ISBN:
Category : Concrete bridges
Languages : en
Pages : 134

View

Book Description

Author: Chris P. Pantelides
Publisher:
ISBN:
Category : Concrete bridges
Languages : en
Pages : 68

View

Book Description
Fiber reinforced polymer composites are an increasingly popular material that can be used for bridge girder retrofit/repair. The purpose of this research, therefore, is to develop methods and design guidelines for repair and retrofit of bridge girders suffering (1) shear strength deficiencies related to end cracking and (2) flexural strength deficiencies related to vehicular collision. Scaled test specimens were fabricated and subjected to cyclic loading in order to instigate damage similar to that caused by end cracking and vehicular collision. Subsequently, the damaged specimens were repaired with external post-tensioned carbon fiber rods and re-tested to failure. This report presents the data from the tests and design guidelines for the use of external post-tensioned carbon fiber rods for repair applications.

Author: R. I. Gilbert
Publisher: CRC Press
ISBN: 9780044454038
Category : Architecture
Languages : en
Pages : 528

View

Book Description
Providing both an introduction to basic concepts and an in-depth treatment of the most up-to-date methods for the design and analysis of concrete of structures, "Design of Prestressed Concrete" will service the needs of both students and professional engineers.

Author: Jessica Lauren Salazar
Publisher:
ISBN:
Category :
Languages : en
Pages : 352

View

Book Description
Pretensioned concrete girders are currently fabricated using 0.5- or 0.6-in. diameter prestressing strands. In recent years, however, it has become of interest to employ larger-diameter 0.7-in. diameter strands to reduce the number of strands and improve the efficiency of pretensioned concrete members. Such a transition requires a considerable initial investment that needs to be justified based on the benefits obtained. Furthermore, the use of 0.7-in. strands would increase the stresses within the end-region of pretensioned elements, which could lead to undesirable cracking and impact the serviceability of the girders. The work presented in this thesis consists of 1) a comprehensive parametric investigation to evaluate the benefits and limitations of using 0.7-in. strands in pretensioned bridge girders, and 2) a full-scale experimental study to investigate the behavior of pretensioned concrete girders with 0.7-in. strands at the time of prestress transfer. The parametric investigation was accomplished by designing thousands of bridge girders with different span lengths, concrete release strengths, and transverse spacings. The results showed that the most noticeable benefit of 0.7-in. strands over 0.6-in. strands was a reduction of up to 35 percent in the number of strands. However, the difference in the total weight of prestressing steel was insignificant. Increasing the release strength of concrete, at least to 7.5 ksi, was found essential to observe benefits in design aspects other than the number of strands. The experimental investigation involved the fabrication of two Tx46 and two Tx70 specimens at the Ferguson Structural Engineering Laboratory. All specimens employed 0.7-in. strands on a 2- by 2-in. grid and the standard detailing currently used for girders with smaller-diameter strands. The observed crack widths in the specimens upon prestress transfer did not exceed those typically observed in Tx-girders with smaller-diameter strands. Therefore, the use of 0.7-in. strands does not seem to trigger a need to modify the end-region detailing in Tx-girders. However, noticeably greater bursting and spalling forces were observed in the end regions of the specimens compared to the demands predicted by AASHTO LRFD provisions. The measured 24-hour transfer length from the specimens also exceeded estimates by AASHTO LRFD and ACI 318-14 provisions.