Caustic-side Solvent Extraction Flowsheet for Optimized Solvent PDF Download

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 5

View

Book Description
Using cesium distribution ratio data from Oak Ridge National Laboratory (ORNL) on the candidates for the optimized solvent, calculations were made to determine how each solvent would perform in the caustic-side solvent extraction (CSSX) process. This report describes the effect that each solvent would have on the CSSX flowsheet for both the current solvent flow rate and the optimum solvent flow rate.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 5

View

Book Description
This work was undertaken to optimize the solvent used in the Caustic Side Solvent Extraction (CSSX) process and to measure key chemical and physical properties related to its performance in the removal of cesium from the alkaline high-level salt waste stored in tanks at the Savannah River Site. The need to adjust the solvent composition arose from the prior discovery that the previous baseline solvent was supersaturated with respect to the calixarene extractant. The following solvent-component concentrations in Isopar{reg_sign} L diluent are recommended: 0.007 M calix[4]arene-bis(tert-octylbenzo-crown-6) (BOBCalixC6) extractant, 0.75 M 1-(2,2,3,3-tetrafluoropropoxy)-3-(4-sec-butylphenoxy)-2-propanol (Cs-7SB) phase modifier, and 0.003 M tri-n-octylamine (TOA) stripping aid. Criteria for this selection included BOBCalixC6 solubility, batch cesium distribution ratios (D{sub Cs}), calculated flowsheet robustness, third-phase formation, coalescence rate (dispersion numbers), and solvent density. Although minor compromises within acceptable limits were made in flowsheet robustness and solvent density, significant benefits were gained in lower risk of third-phase formation and lower solvent cost. Data are also reported for the optimized solvent regarding the temperature dependence of D{sub Cs} in extraction, scrubbing, and stripping (ESS); ESS performance on recycle; partitioning of BOBCalixC6, Cs-7SB, and TOA to aqueous process solutions; partitioning of organic anions; distribution of metals; solvent phase separation at low temperatures; solvent stability to elevated temperatures; and solvent density and viscosity. Overall, the technical risk of the CSSX process has been reduced by resolving previously identified issues and raising no new issues.

Author: M. A. Norato
Publisher:
ISBN:
Category :
Languages : en
Pages : 5

View

Book Description
Researchers successfully demonstrated the chemistry of the Caustic-Side Solvent Extraction (CSSX) flow sheet with optimized solvent. This represents the third such process demonstration using actual Savannah River Site (SRS) high level waste (HLW). The present test differed from previous studies in the use of radioactive waste derived from Tank 37H dissolved salt cake, as opposed to supernate solutions used in previous demonstrations.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 5

View

Book Description
Researchers successfully demonstrated the chemistry and process equipment of the Caustic-Side Solvent Extraction (CSSX) flowsheet for the decontamination of high level waste using a 33-stage, 2-cm centrifugal contactor apparatus at the Savannah River Technology Center. This represents the first CSSX process demonstration using Savannah River Site (SRS) high level waste. Three tests lasting 6, 12, and 48 hours processed simulated average SRS waste, simulated Tank 37H/44F composite waste, and Tank 37H/44F high level waste, respectively.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :

View

Book Description
The purpose of this work is to examine the applicability of the Caustic-Side Solvent Extraction (CSSX) process for the removal of cesium from Hanford tank-waste supernatant solutions in support of the Hanford Interim Pretreatment System (IPS). The Hanford waste types are more challenging than those at the Savannah River Site (SRS) in that they contain significantly higher levels of potassium, the chief competing ion in the extraction of cesium. It was confirmed by use of the CSSX model that the higher levels of potassium depress the cesium distribution ratio (DCs), as validated by measurement of DCs values for four of eight specified Hanford waste-simulant compositions. The model predictions were good to an apparent standard error of ±11%. It is concluded from batch distribution experiments, physical-property measurements, equilibrium modeling, flowsheet calculations, and contactor sizing that the CSSX process as currently employed for cesium removal from alkaline salt waste at the SRS is capable of treating similar Hanford tank feeds. For the most challenging waste composition, 41 stages would be required to provide a cesium decontamination factor (DF) of 5000 and a concentration factor (CF) of 5. Commercial contacting equipment with rotor diameters of 10 in. for extraction and 5 in. for stripping should have the capacity to meet throughput requirements, but testing will be required to confirm that the needed efficiency and hydraulic performance are actually obtainable. Markedly improved flowsheet performance was calculated for a new solvent formulation employing the more soluble cesium extractant BEHBCalixC6 used with alternative scrub and strip solutions, respectively 0.1 M NaOH and 10 mM boric acid. The improved system can meet minimum requirements (DF = 5000 and CF = 5) with 17 stages or more ambitious goals (DF = 40,000 and CF = 15) with 19 stages. Potential benefits of further research and development are identified that would lead to reduced costs, greater adaptability of the process to DOE alkaline salt wastes, and greater readiness for implementation. Such benefits accrue from optimal sizing of centrifugal contactors for application of the CSSX process for the IPS; more accurate modeling of cesium extraction with greater flexibility and applicability to a variety of feeds and flowsheet conditions; and further improving and optimizing the alternative CSSX solvent and scrub/strip system.

Author: M. A. Norato
Publisher:
ISBN:
Category :
Languages : en
Pages : 5

View

Book Description
This report summarizes the results of tests at Savannah River Technology Center with radioactively spiked simulated Tank 37H/44F waste and actual Tank 37H/44F supernate composite waste. The spiked simulant tests demonstrated that stable hydraulic conditions could be maintained with the new solvent formulation and the radioactive feed could be decontaminated to background levels. The 24 hour actual Tank 37H/44F waste test demonstrated similar hydraulic stability and higher decontamination factors.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 39

View

Book Description
The U.S. Department of Energy has selected caustic-side solvent extraction as the preferred cesium removal technology for the treatment of high-level waste stored at the Savannah River Site. Data for the solubility of the extractant, calix[4]arene-bis(tert-octyl benzo-crown-6), acquired and reported for the Salt Processing Program down-select decision, showed the original solvent composition to be supersaturated with respect to the extractant. Although solvent samples have been observed for approximately 1 year without any solids formation, work was completed to define a new solvent composition that was thermodynamically stable with respect to solids formation and to expand the operating temperature with respect to third-phase formation. Chemical and physical data as a function of solvent component concentrations were collected. The data included calix[4]arene-bis(tert-octyl benzo-crown-6) solubility; cesium distribution ratio under extraction, scrub, and strip conditions; flow sheet robustness; temperature range of third-phase formation; dispersion numbers for the solvent against waste simulant, scrub and strip acids, and sodium hydroxide wash solutions; solvent density; viscosity; and surface and interfacial tension. These data were mapped against a set of predefined performance criteria. The composition of 0.007 M calix[4]arene-bis(tert-octyl benzo-crown-6), 0.75 M 1-(2,2,3,3-tetrafluoropropoxy)-3-(4-sec-butylphenoxy)-2-propanol, and 0.003 M tri-n-octylamine in the diluent Isopar{reg_sign} L provided the best match between the measured properties and the performance criteria. Therefore, it is recommended as the new baseline solvent composition.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 5

View

Book Description
The purpose of this work was to provide chemical- and physical-property data addressing the technical risks of the Caustic-Side Solvent Extraction (CSSX) process as applied specifically to the removal of cesium from alkaline high-level salt waste stored at the US Department of Energy Savannah River Site. As part of the overall Salt Processing Project, this effort supported decision-making in regards to selecting a preferred technology among three alternatives: (1) CSSX, (2) nonelutable ion-exchange with an inorganic silicotitanate material and (3) precipitation with tetraphenylborate. High risks, innate to CSSX, that needed specific attention included: (1) chemical stability of the solvent matrix, (2) radiolytic stability of the solvent matrix, (3) proof-of-concept performance of the proposed process flowsheet with simulated waste, and (4) performance of the CSSX flowsheet with actual SRS high-level waste. This body of work directly addressed the chemical-stability risk and additionally provided supporting information that served to plan, carry out, and evaluate experiments conducted by other CSSX investigators addressing the other high risks. Information on cesium distribution in extraction, scrubbing, and stripping served as input for flowsheet design, provided a baseline for evaluating solvent performance under numerous stresses, and contributed to a broad understanding of the effects of expected process variables. In parallel, other measurements were directed toward learning how other system components distribute in the flowsheet. Such components include the solvent components themselves, constituents of the waste, and solvent-degradation products. Upon understanding which components influence flowsheet performance, it was then possible to address in a rational fashion how to clean up the solvent and maintain its stable function.

Author: Lætitia H. Delmau
Publisher:
ISBN:
Category : Chemical engineering
Languages : en
Pages :

View

Book Description

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :

View

Book Description
Researchers successfully demonstrated the chemistry and process equipment of the Caustic-Side Solvent Extraction (CSSX) flowsheet using MaxCalix for the decontamination of high level waste (HLW). The demonstration was completed using a 12-stage, 2-cm centrifugal contactor apparatus at the Savannah River National Laboratory (SRNL). This represents the first CSSX process demonstration of the MaxCalix solvent system with Savannah River Site (SRS) HLW. Two tests lasting 24 and 27 hours processed non-radioactive simulated Tank 49H waste and actual Tank 49H HLW, respectively. A solvent extraction system for removal of cesium from alkaline solutions was developed utilizing a novel solvent invented at the Oak Ridge National Laboratory (ORNL). This solvent consists of a calix[4]arene-crown-6 extractant dissolved in an inert hydrocarbon matrix. A modifier is added to the solvent to enhance the extraction power of the calixarene and to prevent the formation of a third phase. An additional additive is used to improve stripping performance and to mitigate the effects of any surfactants present in the feed stream. The process that deploys this solvent system is known as Caustic Side Solvent Extraction (CSSX). The solvent system has been deployed at the Savannah River Site (SRS) in the Modular CSSX Unit (MCU) since 2008.