Analysis of Resonant Ultrasound Spectroscopy as a Technique to Evaluate Material Property Changes PDF Download

Author: Gautham Manoharan
Publisher:
ISBN:
Category :
Languages : en
Pages : 67

View

Book Description
The objective of this thesis is to validate Resonant Ultrasound Spectroscopy (RUS) as a non-destructive evaluation tool that can be used to study effects of radiation on the mechanical properties of a material, mainly its elastic constants. RUS involves experimentally measuring the resonant frequencies of a sample and calculating the elastic constants based on these measurements. Finite Element Method (FEM) is used to get the frequencies of the modes of free vibration for the sample model. This result depends on the elastic constant values used in the FEM simulation. Studies were conducted to confirm the accuracy of the FEM model, and determine the right configuration and parameters to use for the simulation. Assuming uniform and isotropic elastic property changes, the effects of radiation damage can be quantified by obtaining a set of matching resonant frequencies between the experimental and FEM simulation results, before and after irradiating the sample. This is done by adjusting the elastic constant values used in the simulation so that the results match with the experimentally obtained resonant frequencies. With powerful enough equipment, even real time monitoring is possible in harsh environments, thus pointing out imminent failure.

Author: Abu Rafi Mohammad Iasir
Publisher:
ISBN:
Category :
Languages : en
Pages : 71

View

Book Description
The purpose of this thesis is to study Resonance Ultrasound Spectroscopy(RUS) and it's potential to evaluate the change in interfacial thermal resistance due to irradiation. Resonant Ultrasound Spectroscopy is conventionally used to determine the material properties of elastic bodies. It is a nondestructive technique that is very capable of extracting the elastic constants for a complete anisotropic material. Finite Element Method(FEM) is used to determine the natural frequency of a hollow cylinder. FEM was used due to the shape of the object. An experimental system was developed to capture the resonant frequencies of a hollow cylinder which is similar to Molybdenum-99 target. After successfully determining the resonance frequencies from the spectra, the frequencies were inverted to the elastic constants using the finite element model. Radiation effects on elastic constants was also studied. An investigation was made to assess the usefulness of RUS in evaluating radiation damage of materials. An experimental study was also completed to analyze the differences in RUS spectra in a contact pressure analysis between two cylinders of Molybdenum-99 target.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 10

View

Book Description
All objects exhibit vibrational resonances when mechanically excited. These resonant frequencies are determined by density, geometry, and elastic moduli. Resonant ultrasound spectroscopy (RUS) takes advantage of the known relationship between the parameters. In particular, for a freely suspended object, with three of the four parameters (vibrational spectra, density, geometry, or elastic moduli) known the remaining one can be calculated. From a materials characterization standpoint it is straight-forward to measure density and geometry but less so to measure all the elastic moduli. It has recently become possible to quickly and accurately measure vibrational spectra, and using code written at Los Alamos, calculate all the elastic moduli simultaneously. This is done to an accuracy of better than one percent for compression and 0.1 percent for shear. RUS provides rapid acquisition of materials information here-to-fore obtainable only with difficulty. It will greatly facilitate the use of real materials properties in models and thus make possible more realistic modeling results. The technique is sensitive to phase changes and microstructure. This offers a change to input real data into microstructure and phase change models. It will also enable measurement of moduli at locations in and about a weld thus providing information for a validating coupled thermomechanical calculations.

Author: Albert Migliori
Publisher: Wiley-VCH
ISBN:
Category : Medical
Languages : en
Pages : 224

View

Book Description
This first procedural guide to RUS, Resonant Ultrasound Spectroscopy offers a clear step-by-step tutorial, from developing a preliminary set of resonances to final determination of moduli. The book also contains intermediate computer outputs showing where mistakes are made, how to spot them, and how to remeasure to correct problems. Also a complete reference to the language of RUS, this book is full of clear explanations of every variable, concept, and hard-to-find term currently in use.

Author: 鄭鴻輝
Publisher:
ISBN:
Category :
Languages : en
Pages : 95

View

Book Description

Author: Samantha McGuigan
Publisher:
ISBN:
Category :
Languages : en
Pages :

View

Book Description
Metal additive manufacturing (AM) has started to overshadow traditional manufacturing practices thanks to its ability to produce complex, high-performance and application-customized components. However, AM process parameters have not been optimized, leading to inconsistencies and imperfections such as cracks and pores in parts, as well as deviations from the original design. Nondestructive evaluation (NDE) methods used for part qualification such as x-ray computed tomography (CT) and conventional ultrasonic testing (UT) have limitations in their abilities. X-ray CT is costly, hazardous, and offers limited resolution for larger components while many UT methods have limited applicability for inspection of parts with complex geometries or rough surfaces. Here, we conduct an integrated numerical and experimental study to investigate the feasibility of resonance ultrasound spectroscopy (RUS) as an alternative NDE method to inspect complex AM lattice structures with a varying number of missing struts. The most encouraging results are obtained when test samples have traction-free boundary conditions. The results of numerical simulations including eigenfrequency and frequency domain analyses are promising, indicating that the pristine and defective lattice samples should theoretically be distinguishable. In addition, given a reference intact sample, characterizing the extent of the defect in terms of the number of missing struts appears feasible. We introduce a similarity metric to compare the spectra after being locally normalized. However, the experimental results are not as conclusive. Although pristine and defective lattices may be distinguished for some cases, the number of missing struts cannot be inferred. The discrepancies between the numerical and experimental results are likely due to our simplified assumptions about material properties in numerical simulations and/or the presence of other unaccounted defects and heterogeneities in test samples.

Author: Kevin Joseph Flynn
Publisher:
ISBN:
Category :
Languages : en
Pages :

View

Book Description
This thesis demonstrates the practicability of using Resonant Ultrasound Spectroscopy (RUS) in combination with Finite Element Analysis (FEA) to determine the size and location of a defect in a material of known geometry and physical constants. Defects were analyzed by comparing the actual change in frequency spectrum measured by RUS to the change in frequency spectrum calculated using FEA. FEA provides a means of determining acceptance/rejection criteria for Non-Destructive Testing (NDT). If FEA models of the object are analyzed with defects in probable locations; the resulting resonant frequency spectra will match the frequency spectra of actual objects with similar defects. By analyzing many FEA-generated frequency spectra, it is possible to identify patterns in behavior of the resonant frequencies of particular modes based on the nature of the defect (location, size, depth, etc.). Therefore, based on the analysis of sufficient FEA models, it should be possible to determine nature of defects in a particular object from the measured resonant frequency. Experiments were conducted on various materials and geometries comparing resonant frequency spectra measured using RUS to frequency spectra calculated using FEA. Measured frequency spectra matched calculated frequency spectra for steel specimens both before and after introduction of a thin cut. Location and depth of the cut were successfully identified based on comparison of measured to calculated resonant frequencies. However, analysis of steel specimens with thin cracks, and of ceramic specimens with thin cracks, showed significant divergence between measured and calculated frequency spectra. Therefore, it was not possible to predict crack depth or location for these specimens. This thesis demonstrates that RUS in combination with FEA can be used as an NDT method for detection and analysis of cracks in various materials, and for various geometries, but with some limitations. Experimental results verify that cracks can be detected, and their depth and location determined with reasonable accuracy. However, experimental results also indicate that there are limits to the applicability of such a method, the primary one being a lower limit to the size of crack - especially thickness of the crack - for which this method can be applied.

Author: Dale Ensminger
Publisher: CRC Press
ISBN: 1000994953
Category : Science
Languages : en
Pages : 904

View

Book Description
Updated, revised, and restructured to reflect the latest advances in science and applications, the fourth edition of this best-selling industry and research reference covers the fundamental physical acoustics of ultrasonics and transducers, with a focus on piezoelectric and magnetostrictive modalities. It then discusses the full breadth of ultrasonics applications involving low power (sensing) and high power (processing) for research, industrial, and medical use. This book includes new content covering computer modeling used for acoustic and elastic wave phenomena, including scattering, mode conversion, transmission through layered media, Rayleigh and Lamb waves and flexural plates, modern horn design tools, Langevin transducers, and material characterization. There is more attention on process monitoring and advanced nondestructive testing and evaluation (NDT/NDE), including phased array ultrasound (PAUT), long-range inspection, using guided ultrasonic waves (GUW), internally rotary inspection systems (IRIS), time-of-flight diffraction (TOFD), and acoustic emission (AE). These methods are discussed and applied to both metals and nonmetals using illustrations in various industries, including now additionally for food and beverage products. The topics of defect sizing, capabilities, and limitations, including the probability of detection (POD), are introduced. Three chapters provide a new treatment of high-power ultrasonics, for both fluids and solids, and again, with examples of industrial engineering, food and beverage, pharmaceuticals, petrochemicals, and other process applications. Expanded coverage is given to medical and biological applications, covering diagnostics, therapy, and, at the highest powers, surgery. Key Features Provides an overview of fundamental analysis and transducer technologies needed to design and develop both measurement and processing systems Considers applications in material characterization and metrology Covers ultrasonic nondestructive testing and evaluation and high-power ultrasonics, which involves interactions that change the state of material Highlights medical and biomedical applications of ultrasound, focusing on the physical acoustics and the technology employed for diagnosis, therapy, surgery, and research This book is intended for both the undergraduate and graduate scientists and engineers, as well as the working professional, who seeks to understand the fundamentals together with a holistic treatment of the field of ultrasonics and its diversity of applications.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 125

View

Book Description
The elastic properties of a solid are of considerable interest to both science and technology. Not only do they contain fundamental information about the nature of the inter-atomic bonding in the material, but they also determine the mechanical behavior of solids. In the past few years, considerable effort has been devoted to the study of elastic properties of bulk metallic glasses (BMGs), a relatively new class of metallic materials that display a unique combination of mechanical and physical properties. Our research has focused on Zr-based, Cu-based and Ca-based metallic glasses. Zr-based BMGs are known to have superior glass forming ability and high strength, but their ductility is too low for wide-spread practical applications. Cu-based BMGs recently received wide interest because of their low cost and good mechanical properties. Ca-based BMGs have low glass transition temperature T[subscript g], around 390 K, which make them very attractive to be studied near T[subscript g]. In this work, resonant ultrasound spectroscopy (RUS) has been applied to study the elastic properties of above mentioned BMGs from 5 K to their glass transition temperature T[subscript g]. RUS is a novel technique for determining the elastic moduli of solids, based on the measurement of the resonances of a freely vibrating body. In an RUS experiment, the mechanical resonances of a freely vibrating solid of known shape are measured, and an iteration procedure is used to "match" the measured lines with the calculated spectrum. This allows determination of all elastic constant of the solid from a single frequency scan. Below T[subscript g], the elastic constants of the BMGs under investigation show "normal" behavior, i.e. with increasing temperature, all moduli decrease and Poisson ratio increases. Above T[subscript g] changes in the trends occur due to structural relaxation and crystallization. We confirmed the suggested link between ductility and Poisson ratio: BMGs showing good ductility display high Poisson ratio. By increasing palladium content in Zr50Cu40-[subscript x]Al10Pd[subscript x] alloys, BMGs with high Poisson ratio and thus good ductility have been obtained. In addition, we developed a simple model to provide fast and good estimate of the temperature dependence of elastic constants of BMGs from room temperature measurements.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 4

View

Book Description
The use of mechanical resonances to test properties of materials is perhaps older than the industrial revolution. Early documented cases of British railroad engineers tapping the wheels of a train and using the sound to detect cracks perhaps mark the first real use of resonances to test the integrity of high-performance alloys. Attempts were made in the following years to understand the resonances of solids mathematically, based on the shape and composition. But Nobel Laureate Lord Rayleigh best summarized the state of affairs in 1894, stating {open_quotes}the problem has, for the most part, resisted attack{close_quotes}. More recently, modern computers and electronics have enabled Anderson and co-workers with their work on minerals, and our work at Los Alamos on new materials and manufactured components to advance the use of resonances to a precision non-destructive testing tool that makes anisotropic modulus measurements, defect detection and geometry error detection routine. The result is that resonances can achieve the highest absolute accuracy for any dynamic modulus measurement technique, can be used on the smallest samples, and can also enable detection of errors in certain classes of precision manufactured components faster and more accurately than any other technique.