AN INVESTIGATION OF VARIABLE VALVE TIMING EFFECTS ON HCCI ENGINE PERFORMANCE PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download AN INVESTIGATION OF VARIABLE VALVE TIMING EFFECTS ON HCCI ENGINE PERFORMANCE PDF full book. Access full book title AN INVESTIGATION OF VARIABLE VALVE TIMING EFFECTS ON HCCI ENGINE PERFORMANCE by . Download full books in PDF and EPUB format.
Author: Publisher: ISBN: Category : Languages : en Pages :
Book Description
Abstract : The Homogeneous Charge Compression Ignition (HCCI) engine is a promising combustion concept for reducing NOx and particulate matter (PM) emissions and providing a high thermal efficiency in internal combustion engines. This concept though has limitations in the areas of combustion control and achieving stable combustion at high loads. For HCCI to be a viable option for on-road vehicles, further understanding of its combustion phenomenon and its control are essential. Thus, this thesis has a focus on both the experimental setup of an HCCI engine at Michigan Technological University (MTU) and also developing a physical numerical simulation model called the Sequential Model for Residual Affected HCCI (SMRH) to investigate performance of HCCI engines. The primary focus is on understanding the effects of intake and exhaust valve timings on HCCI combustion. For the experimental studies, this thesis provided the contributions for development of HCCI setup at MTU. In particular, this thesis made contributions in the areas of measurement of valve profiles, measurement of piston to valve contact clearance for procuring new pistons for further studies of high geometric compression ratio HCCI engines. It also consists of developing and testing a supercharging station and the setup of an electrical air heater to extend the HCCI operating region. The HCCI engine setup is based on a GM 2.0 L LHU Gen 1 engine which is a direct injected engine with variable valve timing (VVT) capabilities. For the simulation studies, a computationally efficient modeling platform has been developed and validated against experimental data from a single cylinder HCCI engine. In-cylinder pressure trace, combustion phasing (CA10, CA50, BD) and performance metrics IMEP, thermal efficiency, and CO emission are found to be in good agreement with experimental data for different operating conditions. Effects of phasing intake and exhaust valves are analyzed using SMRH. In addition, a novel index called Fuel Efficiency and Emissions (FEE) index is defined and is used to determine the optimal valve timings for engine operation through the use of FEE contour maps.
Author: Publisher: ISBN: Category : Languages : en Pages :
Book Description
Abstract : The Homogeneous Charge Compression Ignition (HCCI) engine is a promising combustion concept for reducing NOx and particulate matter (PM) emissions and providing a high thermal efficiency in internal combustion engines. This concept though has limitations in the areas of combustion control and achieving stable combustion at high loads. For HCCI to be a viable option for on-road vehicles, further understanding of its combustion phenomenon and its control are essential. Thus, this thesis has a focus on both the experimental setup of an HCCI engine at Michigan Technological University (MTU) and also developing a physical numerical simulation model called the Sequential Model for Residual Affected HCCI (SMRH) to investigate performance of HCCI engines. The primary focus is on understanding the effects of intake and exhaust valve timings on HCCI combustion. For the experimental studies, this thesis provided the contributions for development of HCCI setup at MTU. In particular, this thesis made contributions in the areas of measurement of valve profiles, measurement of piston to valve contact clearance for procuring new pistons for further studies of high geometric compression ratio HCCI engines. It also consists of developing and testing a supercharging station and the setup of an electrical air heater to extend the HCCI operating region. The HCCI engine setup is based on a GM 2.0 L LHU Gen 1 engine which is a direct injected engine with variable valve timing (VVT) capabilities. For the simulation studies, a computationally efficient modeling platform has been developed and validated against experimental data from a single cylinder HCCI engine. In-cylinder pressure trace, combustion phasing (CA10, CA50, BD) and performance metrics IMEP, thermal efficiency, and CO emission are found to be in good agreement with experimental data for different operating conditions. Effects of phasing intake and exhaust valves are analyzed using SMRH. In addition, a novel index called Fuel Efficiency and Emissions (FEE) index is defined and is used to determine the optimal valve timings for engine operation through the use of FEE contour maps.
Author: Hrishikesh Abhay Saigaonkar Publisher: ISBN: Category : Automobiles Languages : en Pages : 141
Book Description
For the experimental studies, this thesis provided the contributions for development of HCCI setup at MTU. In particular, this thesis made contributions in the areas of measurement of valve profiles, measurement of piston to valve contact clearance for procuring new pistons for further studies of high geometric compression ratio HCCI engines. It also consists of developing and testing a supercharging station and the setup of an electrical air heater to extend the HCCI operating region. The HCCI engine setup is based on a GM 2.0 L LHU Gen 1 engine which is a direct injected engine with variable valve timing (VVT) capabilities.
Author: National Research Council Publisher: National Academies Press ISBN: 0309373913 Category : Science Languages : en Pages : 812
Book Description
The light-duty vehicle fleet is expected to undergo substantial technological changes over the next several decades. New powertrain designs, alternative fuels, advanced materials and significant changes to the vehicle body are being driven by increasingly stringent fuel economy and greenhouse gas emission standards. By the end of the next decade, cars and light-duty trucks will be more fuel efficient, weigh less, emit less air pollutants, have more safety features, and will be more expensive to purchase relative to current vehicles. Though the gasoline-powered spark ignition engine will continue to be the dominant powertrain configuration even through 2030, such vehicles will be equipped with advanced technologies, materials, electronics and controls, and aerodynamics. And by 2030, the deployment of alternative methods to propel and fuel vehicles and alternative modes of transportation, including autonomous vehicles, will be well underway. What are these new technologies - how will they work, and will some technologies be more effective than others? Written to inform The United States Department of Transportation's National Highway Traffic Safety Administration (NHTSA) and Environmental Protection Agency (EPA) Corporate Average Fuel Economy (CAFE) and greenhouse gas (GHG) emission standards, this new report from the National Research Council is a technical evaluation of costs, benefits, and implementation issues of fuel reduction technologies for next-generation light-duty vehicles. Cost, Effectiveness, and Deployment of Fuel Economy Technologies for Light-Duty Vehicles estimates the cost, potential efficiency improvements, and barriers to commercial deployment of technologies that might be employed from 2020 to 2030. This report describes these promising technologies and makes recommendations for their inclusion on the list of technologies applicable for the 2017-2025 CAFE standards.
Author: Alexander E. Schramm Publisher: ISBN: Category : Automobiles Languages : en Pages : 114
Book Description
Homogeneous charge compression ignition (HCCI) combustion can produce higher efficiencies and lower emissions when compared to tradition spark or compression ignition engines. This study reports an experimental investigation into the effects of valve timings on HCCI combustion conditions. Using a single cylinder engine with state-of-the-art electromagnetic variable valve timing (EVVT) fully independent valves, a series of tests are conducted with varying negative valve overlap (NVO). The in-cylinder residual trapped by the NVO causes an advance in combustion timing, a shortening of burn duration as well as increase in load and increase in brake specific fuel consumption. Asymmetric valve timings are also investigated and show complex behavior with high sensitivity of combustion timing in certain operating ranges. Finally, these strategies are implemented as a set of feedback controllers including a proportional-integral (PI) controller and a feedforward with integral action controller. Both controllers have good tracking for step changes in combustion timing setpoint with the feedforward controller providing a rise time of just four cycles.
Author: Hua Zhao Publisher: CRC Press ISBN: Category : Technology & Engineering Languages : en Pages : 562
Book Description
Homogeneous charge compression ignition (HCCI)/controlled auto-ignition (CAI) has emerged as one of the most promising engine technologies with the potential to combine fuel efficiency and improved emissions performance, offering reduced nitrous oxides and particulate matter alongside efficiency comparable with modern diesel engines. Despite the considerable advantages, its operational range is rather limited and controlling the combustion (timing of ignition and rate of energy release) is still an area of on-going research. Commercial applications are, however, close to reality. HCCI a.
Author: Krzysztof Jan Siczek Publisher: Butterworth-Heinemann ISBN: 0081009739 Category : Technology & Engineering Languages : en Pages : 299
Book Description
Tribological Processes in Valvetrain Systems with Lightweight Valves: New Research and Modelling provides readers with the latest methodologies to reduce friction and wear in valvetrain systems—a severe problem for designers and manufacturers. The solution is achieved by identifying the tribological processes and phenomena in the friction nodes of lightweight valves made of titanium alloys and ceramics, both cam and camless driven. The book provides a set of structured information on the current tribological problems in modern internal combustion engines—from an introduction to the valvetrain operation to the processes that produce wear in the components of the valvetrain. A valuable resource for teachers and students of mechanical or automotive engineering, as well as automotive manufacturers, automotive designers, and tuning engineers. Shows the tribological problems occurring in the guide-light valve-seat insert Combines numerical and experimental solutions of wear and friction processes in valvetrain systems Discusses various types of cam and camless drives the valves used in valve trains of internal combustion engines—both SI and CI Examines the materials used, protective layers and geometric parameters of lightweight valves, as well as mating guides and seat inserts
Author: Banh Tien Long Publisher: Springer Nature ISBN: 3030996662 Category : Technology & Engineering Languages : en Pages : 982
Book Description
This book presents selected, peer-reviewed proceedings of the International Conference on Advanced Mechanical Engineering, Automation and Sustainable Development 2021 (AMAS2021), held in the city of Ha Long, Vietnam, from November 4 to 7, 2021. AMAS2021 is a special meeting of the International Conference on Material, Machines and Methods for Sustainable Development (MMMS), with a strong focus on automation and fostering an overall approach to assist policy makers, industries, and researchers at various levels to position local technological development toward sustainable development. The contributions published in this book stem from a wide spectrum of research, ranging from micro- and nanomaterial design and processing, to special applications in mechanical technology, environmental protection, green development, and climate change mitigation. A large group of contributions selected for these proceedings also focus on modeling and manufacturing of ecomaterials.
Author: Li Kai Publisher: World Scientific ISBN: 9814295043 Category : Technology & Engineering Languages : en Pages : 546
Book Description
Held in Singapore from 9 to 11 October 2009, the 2009 International Conference on Chemical, Biological and Environmental Engineering (CBEE 2009) aims to provide a platform for researchers, engineers, academicians as well as industrial professionals from all over the world to present their research and development activities in chemical, biological and environmental engineering. Conference delegates will also have the opportunity to exchange new ideas and application experiences, establish business or research relations and find global partners for future collaboration. Sample Chapter(s). Chapter 1: The Future of Biopharmaceutics'' Production (92 KB). Contents: Study on Pyrolysis Characteristics of Electronic Waste (J Sun et al.); Application of Noise Mapping on Environmental Management (K-T Tsai et al.); Characteristics and Transport Properties of Two Modified Zero Valent Iron (Y-H Lin et al.); Synthesis of Visible Light Active N-Doped Titania Photocatalyst (C Kusumawardani et al.); CFD-PBM Modeling of Vertical Bubbly Flows (M R Rahimi & H Karimi); Hydrotalcite-Like Synthesis Using Magnesium from Brine Water (E Heraldy et al.); Cement/Activated-Carbon Solidification/Stabilization Treatment of Nitrobenzene (Z Su et al.); Investigation of Fish Species Biodiversity in Haraz River (I Piri et al.); Risk Assessment of Fluoride in Indian Context (V Chaudhary & M Kumar); Light Transmission In Fluidized Bed (E Shahbazali et al.); Drying of Mushroom Using a Solar Tunnel Dryer (M A Basunia et al.); and other papers. Readership: Researchers, engineers, academicians and industrial professionals in related fields of chemical, biological and environmental engineering.
Author: 
Author: 
Author: Hrishikesh Abhay Saigaonkar
Author: Brian Kenneth Bolton
Author: National Research Council
Author: Alexander E. Schramm
Author: Hua Zhao
Author: Krzysztof Jan Siczek
Author: Banh Tien Long
Author: Li Kai
Author: Dennis G. Nitz