Alternative Design of Low-tension Cable Barrier Adjacent to Steep Slopes PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Alternative Design of Low-tension Cable Barrier Adjacent to Steep Slopes PDF full book. Access full book title Alternative Design of Low-tension Cable Barrier Adjacent to Steep Slopes by Robert W. Bielenberg. Download full books in PDF and EPUB format.
Author: Robert W. Bielenberg Publisher: ISBN: Category : Roads Languages : en Pages : 124
Book Description
In the early 2000s, MwRSF conducted full-scale crash testing on low-tension cable barrier systems installed adjacent to 1.5H:1V slopes. A design was successfully tested according to NCHRP Report 350 criteria, but the tested and approved configuration utilized a 4-ft (1.2 m) post spacing and a 4-ft (1.2 m) offset from the slope break point (SBP). Therefore, NDOT funded this research study to investigate if revisions to the low-tension cable barrier system could be identified which were likely to satisfy MASH requirements and which would be more cost-effective. This research study was conducted to investigate alternative low-tension cable barrier designs and configurations which would be likely to satisfy MASH TL-3 impact conditions and which would improve cost-effectiveness and/or usability for NDOT. Test nos. LTCB-1 through LTCB-5 were conducted on S3x5.7 steel posts at varying offset distances from a 1.8H:1V slope. Test no. LTCB-6 was conducted to evaluate the propensity for S3x5.7 posts to penetrate a small car test vehicle's floor pan, and tearing was observed. Subsequent component tests of an HSS3x2x1/8 tubular post alternative in development for use with high-tension cable median barrier systems was found to provide acceptable performance while mitigating floor pan tearing. Computer simulations were performed to investigate alternative barrier configurations. Various combinations of post spacing, barrier offset, and cable heights were evaluated. It was determined that systems with 3-ft (0.9-m) offset from the slope with 4-ft (1.2-m) post spacing, or 4-ft (1.2-m) offset from the slope with 6-ft (1.8-m) post spacing, may perform acceptably according to MASH TL-3 test designation no. 3-11.
Author: Robert W. Bielenberg Publisher: ISBN: Category : Roads Languages : en Pages : 124
Book Description
In the early 2000s, MwRSF conducted full-scale crash testing on low-tension cable barrier systems installed adjacent to 1.5H:1V slopes. A design was successfully tested according to NCHRP Report 350 criteria, but the tested and approved configuration utilized a 4-ft (1.2 m) post spacing and a 4-ft (1.2 m) offset from the slope break point (SBP). Therefore, NDOT funded this research study to investigate if revisions to the low-tension cable barrier system could be identified which were likely to satisfy MASH requirements and which would be more cost-effective. This research study was conducted to investigate alternative low-tension cable barrier designs and configurations which would be likely to satisfy MASH TL-3 impact conditions and which would improve cost-effectiveness and/or usability for NDOT. Test nos. LTCB-1 through LTCB-5 were conducted on S3x5.7 steel posts at varying offset distances from a 1.8H:1V slope. Test no. LTCB-6 was conducted to evaluate the propensity for S3x5.7 posts to penetrate a small car test vehicle's floor pan, and tearing was observed. Subsequent component tests of an HSS3x2x1/8 tubular post alternative in development for use with high-tension cable median barrier systems was found to provide acceptable performance while mitigating floor pan tearing. Computer simulations were performed to investigate alternative barrier configurations. Various combinations of post spacing, barrier offset, and cable heights were evaluated. It was determined that systems with 3-ft (0.9-m) offset from the slope with 4-ft (1.2-m) post spacing, or 4-ft (1.2-m) offset from the slope with 6-ft (1.8-m) post spacing, may perform acceptably according to MASH TL-3 test designation no. 3-11.
Author: American Association of State Highway and Transportation Officials. Task Force for Roadside Safety Publisher: ISBN: Category : Roads Languages : en Pages : 560
Author: Malcolm H. Ray Publisher: ISBN: Category : Automobiles Languages : en Pages : 172
Book Description
This synthesis will be of interest to state department of transportation (DOT) roadway design, traffic, structural, maintenance, and research engineers and others concerned with highway safety issues. This synthesis describes the current state of the practice for the use of guardrails and median barriers and their crashworthiness. It includes information about the crashworthiness and typical applications of the most common, permanently installed, nonproprietary guardrail and median barrier systems used in the United States today. A significant amount of detail is included in the text to aid the design, selection, and locating processes for safe and effective guardrails and median barriers. The report presents data obtained from a review of the literature and a survey of state DOTs. The synthesis presents a description of the typical longitudinal barriers in use today, including drawings, the extent of their use, and the most recent testing on each guardrail and barrier system, with particular emphasis on NCHRP Report 230 and 350 requirements. In addition, it discusses the maintenance issues, cost constraints, and common problems with each type of barrier. The synthesis only discusses the crashworthiness of guardrails and median barriers; their transitions and terminals are not discussed.
Author: Publisher: ISBN: 9781523119592 Category : Highway engineering Languages : en Pages :
Book Description
Highway engineers, as designers, strive to meet the needs of highway users while maintaining the integrity of the environment. Unique combinations of design controls and constraints that are often conflicting call for unique design solutions. A Policy on Geometric Design of Highways and Streets provides guidance based on established practices that are supplemented by recent research. This document is also intended as a comprehensive reference manual to assist in administrative, planning, and educational efforts pertaining to design formulation
Author: Gordon Keller Publisher: ISBN: 9781998295333 Category : Languages : en Pages : 0
Book Description
This Low-Volume Roads Engineering Best Management Practices Field Guide is intended to provide an overview of the key planning, location, design, construction, and maintenance aspects of roads that can cause adverse environmental impacts and to list key ways to prevent those impacts. Best Management Practices are general techniques or design practices that, when applied and adapted to fit site-specific conditions, will prevent or reduce pollution and maintain water quality. BMPs for roads have been developed by many agencies since roads often have a major adverse impact on water quality, and most of those impacts are preventable with good engineering and management practices. Roads that are not well planned or located, not properly designed or constructed, not well maintained, or not made with durable materials often have negative effects on water quality and the environment.
Author: Marvin Denmark Publisher: ISBN: 9780615438139 Category : Languages : en Pages : 88
Book Description
Marvin Denmark, a builder and craftsman with 45+ years of experience, demonstrates the process he used to design and construct a small cable suspension bridge. This book includes some suspension bridge history along with engineering considerations, then explains and illustrates with diagrams and full-color photos the step by step process that was used to complete the project. His blog, wildcatman.wordpress.com, has excerpts from the book, a new cable locking system design, and a recent price list for parts for his bridge. A trailer for the cable locking system including video of the bridge building process is here:http://www.youtube.com/watch?v=cLXrzC9K5wQ Anyone who is looking for ideas for a footbridge that is relatively easy to build without the use of heavy equipment or difficult to replace components may benefit from the design in this book and by using the patented "cable locking system."
Author: Robert W. Bielenberg
Author: Robert W. Bielenberg
Author: 
Author: 
Author: American Association of State Highway and Transportation Officials. Task Force for Roadside Safety
Author: National Cooperative Highway Research Program
Author: Malcolm H. Ray
Author: 
Author: 
Author: Gordon Keller
Author: Marvin Denmark